• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.2
• /
• pp.290-299
• /
• 2017

Reconfigurable flight control using various kinds of adaptive control methods has been studied since the 1970s to enhance the survivability of aircraft in case of severe in-flight failure. Early studies were mainly focused on the failure of actuators. Recently, studies of reconfigurable flight controls that can accommodate complex damage (partial wing and tail loss) in conventional aircraft were reported. However, the partial wing loss effects on the aerodynamics of conventional type aircraft are quite different to those of BWB(blended wing body) aircraft. In this paper, a reconfigurable flight control algorithm was designed using a direct model reference adaptive method to overcome the instability caused by a complex damage of a BWB aircraft. A model reference adaptive control was incorporated into the inner loop rate control system enhancing the performance of the baseline control to cope with abrupt loss of stability. Gains of the model reference adaptive control were polled out using the Liapunov's stability theorem. Outer loop attitude autopilot was designed to manage roll and pitch of the BWB UAV as well. A 6-DOF dynamic model was built-up, where the normal flight can be made to switch to the damaged state abruptly reflecting the possible real flight situation. 22% of right wing loss as well as 25% loss for both vertical tail and rudder control surface were considered in this study. Static aerodynamic coefficients were obtained via wind tunnel test. Numerical simulations were conducted to demonstrate the performance of the reconfigurable flight control system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.11
• /
• pp.999-1005
• /
• 2007

In case of an abnormal condition of control surface, the real-time estimation of aerodynamic derivatives are required for the reconfigurable control system to be flight for missions or return to the head office. The goal of this paper is to represent a technique of fault detection to the control surface as a base research to the fault tolerant control system for safety improvement of UAV. The real-time system identification for the fault detection to the control surface was applied with the recursive Fourier Transform and verified through the HILS and flight test. The failures of the control surface are detected by comparing the control derivatives in fault condition with the normal condition. As a result from the flight test, we have confirmed that the control derivatives of fault condition less than about 50% in the normal condition.

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.2
• /
• pp.531-536
• /
• 2024

Control drones, which are recently classified as smart agricultural machines in the agricultural field, are striving to build smart control and automatic control systems by combining hardware and software in order to shorten working hours and increase the effectiveness of control in the aging era of rural areas. In this paper, the characteristics of the nozzle dedicated to the control drone were analyzed as a basic study for the establishment of management control and automatic control systems. In order to consider various variables such as the type of various drone models, controller, wind, flight speed, flight altitude, weather conditions, and UAV pesticide types, related studies are needed to be able to present the drug spraying criteria in consideration of the characteristics and versatility of the nozzle. Therefore, to enable the consideration of various variables, flow analysis (CFD) simulation was conducted based on the self-designed nozzle, and the theoretical and experimental values of the droplet distribution were compared and analyzed through water reduction experiments. In the future, we intend to calculate accurate scattering in consideration of various variables according to drone operation and use it in management control and automatic control systems.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.12
• /
• pp.1181-1188
• /
• 2014

In this paper, we propose a novel concept foran unmanned delivery service using a cooperative heterogeneous unmanned system consisting of a self-driving car and an unmanned aerial vehicle (UAV). The proposed concept is suitable to deliver parcels in high-density and high-rise urban or residential areas. In order to achieve the proposed concept, we will develop acooperative heterogeneous unmanned system. Customers can order goods using a smartphone application and the order information, including the position of the customer and the order time, and the package is transported automatically by the unmanned systems. The system assigns the tasks suitable for each unmanned vehicle by analyzing it based on map information. Performance is validated by experiments consisting of autonomous driving and flight tests in a real environment. For more evaluation, the landing position error analysis is performed using circular error probability (CEP).

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.2
• /
• pp.314-324
• /
• 2018

This paper proposes a linear distributed target tracking filter for multiple unmanned aerial vehicles(UAVs) sharing their passive sensor measurements through communication channels. Different from the conventional nonlinear filtering schemes, the distributed passive target tracking problem is newly formulated within the framework of a linear robust state estimation theory incorporated with a linear uncertain measurement equation including the coordinate transform uncertainty. To effectively cope with the performance degradation due to the coordinate transform uncertainty, a linear consistent robust Kalman filter(CRKF) theory is devised and applied for designing a distributed passive target tracking filter. Through the simulations for typical UAV surveillance mission, the superior performance of the proposed method over the existing schemes of distributed passive target tracking are demonstrated.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.6
• /
• pp.618-638
• /
• 2020

An unmanned aerial vehicle(UAV) refers to an aircraft that has all or part of its functions to autonomously fly by grasping the surrounding environment by remote control on the ground without a pilot on board. With the development of unmanned aerial technology, civil/military forces are developing unmanned aerial vehicles for various purposes. In order to control unmanned aerial vehicles from the ground, communication protocols between unmanned aerial vehicles and ground control equipment are required, and civil/military forces have developed and used a photocall for different purposes. In this study, the characteristics of the MAVLink protocol used in the private sector and the STANAG 4586 protocol used in the military are compared/analyzed in detail to find elements to complement each other and to draw improvement measures for protocol unification.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.11
• /
• pp.1042-1051
• /
• 2011

In this paper, a total operating environment equipped with onboard wireless communication systems and ground-based mission control systems is proposed for simultaneous operation of multiple UAVs. A variety of operating structures are studied and classified systematically based on types and usages of the components. For each operating system, the strength, weakness and reliability aspects are investigated. Based on these results, a proper operating system configuration is determined and components are developed for mission formation flight. Proposed system can make a formation flight of various UAVs, execute complex missions decentralizing mission to several UAVs and cooperate several missions.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.6
• /
• pp.99-107
• /
• 2019

With the development of various types of military Unmanned Aircraft(UA)s, the need for interworking and integration between different platforms gradually increased. In order to ensure interoperability at each military UA System(UAS) level, North Atlantic Treaty Organization(NATO) has established STANAG-4586 "Standard Interfaces of Unmanned Aircraft(UA) Control Systems(UCS) for NATO UA Interoperability-Interface Control Document". This paper looks at the basic design structure of STANAG-4586 and the changes on Edition 4 to enhance joint operational capability through reflecting and updating the interoperability design of the military UAS. In particular, we analyze the enhanced Datalink Transition/Handover Procedure and Autonomous functions, one of the biggest features added to the edition. Through this, we propose a modification of UA data link exclusive control using UA Bypass structure, which was impossible in the one-to-one communication structure between existing UA and Core UCS(CUCS). We also suggest ways to improve UA operational reliability by applying Autonomous Functions that directly decides how to deal with emergency situations, rather than by a remote operator over CUCS.

• Journal of Platform Technology
• /
• v.8 no.1
• /
• pp.3-9
• /
• 2020

In Korea, 63% of the nation's land is made up of forests, and the average temperature of the earth has been increasing. Forest service has been operating a proactive control system for preventing the spread of forest pests such as Pine wilt disease. but there were some hurdles in timely control due to weather, topography and manpower management difficulties. In this paper, we propose a model for building fast, accurate and efficient control system by categorizing the damage and dead wood automatically based on the images acquired using small unmanned aerial vehicles based on information and communication technology. In particular, the proposed model establishes an effective response system for government affairs through cooperation in the private sector. It can also create new jobs in the unmanned aerial vehicle business and service industries.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.4
• /
• pp.662-674
• /
• 2017

This paper describes the multidisciplinary design optimization (MDO) process of a tailless unmanned combat aerial vehicle (UCAV) using global variable fidelity aerodynamic analysis. The developed tailless UAV design framework combines multiple disciplines that are based on low-fidelity and empirical analysis methods. An automated high-fidelity aerodynamic analysis is efficiently integrated into the MDO framework. Global variable fidelity modeling algorithm manages the use of the high-fidelity analysis to enhance the overall accuracy of the MDO by providing the initial sampling of the design space with iterative refinement of the approximation model in the neighborhood of the optimum solution. A design formulation was established considering a specific aerodynamic, stability and control design features of a tailless aircraft configuration with a UCAV specific mission profile. Design optimization problems with low-fidelity and variable fidelity analyses were successfully solved. The objective function improvement is 14.5% and 15.9% with low and variable fidelity optimization respectively. Results also indicate that low-fidelity analysis overestimates the value of lift-to-drag ratio by 3-5%, while the variable fidelity results are equal to the high-fidelity analysis results by algorithm definition.