• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.72-73
• /
• 2021

For the development of high-fluidity concrete using low-binder, The effect of the use of the developed acrylic viscosity agent on the physical properties of concrete evaluated. The amount acrylic viscosity agent used was 1.5%, 1.7%, and 2.0% based on the binder amount of 400kg/m3, and slump flow test, slump flow 500mm arrival time measurement, air volume measurement, and U-Box passing test were conducted to determine the effect of the physical properties of concrete. it was judged that 1.5% of the acrylic viscosity agent used in high-fluidity concrete using low-binder was most suitable.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.129-130
• /
• 2021

For the development of high-fluidity concrete using low-binder, The effect of the use of the developed acrylic viscosity agent on the physical properties of concrete evaluated. The amount acrylic viscosity agent used was 0.28%, 0.29% and 0.30% based on the binder amount of 350kg/m³, and slump flow test, air volume measurement, U-Box passing test and strength compressive were conducted to determine the effect of the physical properties of concrete. it was judged that 0.29% of the cellulose type viscosity agent used in high-fluidity concrete using low-binder was most suitable.

• Wind and Structures
• /
• v.20 no.2
• /
• pp.349-361
• /
• 2015

Higher-mode vertical vortex-induced vibrations (VIV) have been observed on several steel box-girder suspension bridges where different vertical modes are selectively excited in turn with wind velocity in accordance with the Strouhal law. Understanding the relationship of VIV amplitudes for different modes of vibration is very important for wind-resistant design of long-span box-girder suspension bridges. In this study, the basic rectangular cross-section with side ratio of B/D=6 is used to investigate the effect of different modes on VIV amplitudes by section model tests. The section model is flexibly mounted in wind tunnel with a variety of spring constants for simulating different modes of vibration and the non-dimensional vertical amplitudes are determined as a function of reduced velocity U/fD. Two 'lock-in' ranges are observed at the same onset reduced velocities of approximately 4.8 and 9.4 for all cases. The second 'lock-in' range, which is induced by the conventional vortex shedding, consistently gives larger responses than the first one and the Sc-normalized maximum non-dimensional responses are almost the same for different spring constants. The first 'lock-in' range where the vibration frequency is approximately two times the vortex shedding frequency is probably a result of super-harmonic resonance or the "frequency demultiplication". The main conclusion drawn from the section model study, central to the higher-mode VIV of suspension bridges, is that the VIV amplitude for different modes is the same provided that the Sc number for these modes is identical.

• Journal of the Korea Convergence Society
• /
• v.10 no.12
• /
• pp.1-6
• /
• 2019

In this paper, we have developed an app that can control IPTV - Miracast and the Internet with Android 7.0 on the embedded board. The app can be controlled by the remote control of IPTV and can receive TV when using IPTV. And Miracast and Embedded board are put into the power saving mode. When one mode is selected in this way, the other two modes enter the power saving mode and the power saving control technology is applied to reduce energy consumption. The board used in this paper was Android version 7.1.2 version of Raspberry pie 3B / B + and Asus Tinker board s, and Android Studio program was used to make the app and a synchronization control program was also developed to operate with IPTV remote control. The operation of the Android start program using the power saving power control technology and the remote control synchronization control program developed in this way is confirmed to be normal operation as a result of applying to the actual IPTV.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.3
• /
• pp.107-115
• /
• 1995

A simple estimation system of ultimate and residual strength for ship structures is developed on the Open-Window system of SUN4 engineering workstation. System development consists of three stages. Firstly, various ultimate longitudinal strength estimation methods are investigated and some rational estimation methods are adopted based on the parametric comparison of various hulls or box girders. Secondly, these selected and newly formulated methods are linked with elastic & perfectly plastic section modulus calculation procedure. Therefore, the longitudinal hull girder strength can be calculated in the intact and damaged conditions due to the grounding or collision of hull structure. Finally, an exclusive system is developed such that whole procedures are proceeded under the window management system using mouse button and elastic and perfect plastic stress conditions. Also longitudinal members are plotted automatically under three dimensional graphic circumstances. These established program is tested for various actual ships, and some examples are illustrated.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.114.2-114.2
• /
• 2017

Transparent film heaters (TFHs) based on Joule heating are currently an active research area. However, TFHs based on an indium tin oxide (ITO) monolayer have a number of problems. For example, heating is concentrated in part of the device. Also, heating efficiency is low because it has high sheet resistance ($R_S$). Resistance of indium zinc oxide (IZO) is similar to ITO and it can be used to flexible applications due to its amorphous structure. To solve these problems, our study introduced hybrid layers of IZO/Ag/IZO deposited by magnetron sputtering, and the electrical, optical, and thermal properties were estimated for various thickness of the metal interlayer. It was found that the sheet resistance of the multilayer was mainly dependent on the thickness of the Ag layers. The $R_S$ of IZO(40)/Ag/IZO(40nm) multilayer was 5.33, 3.29, $2.15{\Omega}/{\Box}$ for Ag thickness of 10, 15, and 20nm, respectively, while the $R_S$ of an IZO monolayer(95nm) was $59.58{\Omega}/{\Box}$. The optical transmittance at 550nm for the IZO(95nm) monolayer is 81.6%, and for the IZO(40)/Ag/IZO(40nm) multilayers with Ag thickness 10, 15 and 20nm, is for 72.8, 78.6, and 63.9%, respectively. The defrost test showed that the film with the lowest RS had the highest heat generation rate (HGR) for the same applied voltage. The results indicated that IZO(40)/Ag(15)/IZO(40nm) multilayer has the best suitable property, which is a promising thin film heater for the application in vehicle windshield.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.4
• /
• pp.439-447
• /
• 2011

Longitudinal cracks due to traffic truck loadings that are caused by local deformations of steel orthotropic bridge decks are sometimes observed in the wearing surface. So, underlying causes of the longitudinal pavement crack induced by structural behaviors of steel decks are investigated in this study. For this purpose, The rational finite element model of the steel deck and the pavement having the box girder is developed and a parametric study is performed by varying thickness or elastic modulus ratios of both the steel deck plate and the pavement. As a result, a large tensile strain above the webs of the u-rib and the box girder, which becomes the main cause of the cracks of the pavement, is detected from variation of the normal strain component of the wearing surface in the transverse direction.

• The KIPS Transactions:PartD
• /
• v.8D no.6
• /
• pp.681-690
• /
• 2001

In this paper, we propose a steering concept that considers overall aspects in the CBSD (Component-Based Software Development) environments. While many researches which are concentrated on using components, market promotion and component development itself seem to be insufficient. To overcome this problem, we introduce a brokerage concept called“Value-Added Brokerage Concept”that provides the following three services：1) domain architecture-based component promotion, 2) intelligent component search, and 3) white-box service. Domain architecture-based component promotion facilitates balancing component production and promoting architecture-level large scale reuse. Intelligent component search enables to overcome the long time search and selection problem. Finally, white-box service is for solving maintenance problems, which is one of the most critical problem in the CBSD environments. Especially, we expect this proposed concept would be well adapted to our national environments.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.3
• /
• pp.50-57
• /
• 1997

The presence of slime in paper mills is practically universal. Many researches have been performed for many years to resolve the problem caused by the slime in pulp and paper mill. Many papers have been published to show the bacteria is a major cause of paper mill slime. Now that the recycling of the water has been increased and the regulations of a toxic chemical dosage have become more strengthen, the importance of the control of slime in pulp and paper mill recently has been more recognized. Therefore, to produce quality products at the lowest economic and environmental costs, a through study of the microbial ecology and the indentification of troublesome slime-forming bacteria is a quite necessary. The purpose of this paper is to indentify slime~forming bacteria isolated from the papermaking process. The samples were taken from four parts of making fine paper : machine chest, head box, wire part, white water tank. Machine chest showed the most numbers of bacteria, numbering $2.55{\times}10^7$. The different colony types were taken from the 105 dilution plate. Nine bacteria were identified u sing the Biolog system and the vitek system: 6 gram-negative bacteria, 3 gram-positive bacteria. They are Pseudomonas paucimobilis B., Staphylococcus sp., Acinetobacter calcoaceticus., Pseudomonas cepacia, Actinobaci1lus capsulatus, Acidovorax sp., Flavobacterium sp., and Staphylococcus auricularis in addition to one unidentified sp., Among them. Pseudomonas paucimobillis was found in all places where the samples were taken. And, each parts had the different predominant bacteria in it : Pseudomonas paucimobilis B. in machine chest, Acinetobactor calcoaceticus. in Wire Part and Staphylococcus sp. in head box.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.120-120
• /
• 2010

최근 투명전도성 산화물(Transparent Conductive Oxide, TCO) 박막은 액정 표시소자(LCD), 플라즈마 디스플레이 패널(PDP), 압전소자 및 태양전지의 투명소자로 사용되어지고 있다. 현재 가장 널리 사용되어지고 있는 투명전극물질인 인듐주석산화물(indium tin oxide, ITO)은 낮은 비저항과 높은 투과율을 가지고 있지만, 높은 원자재의 가격 및 수소플라즈마 처리시 In과 Sn이 환원되어 전기적, 광학적으로 불안정한 문제점들이 지적되고 있다. 이러한 문제점들을 해결하기 위해 최근 적외선 및 가시광선 영역에서 높은 투과도 및 전기 전도성과 수소플라즈마에 대한 화학적 안정성을 갖는 ZnO를 기반으로 3족 원소를 첨가한 새로운 투명 전도막에 대한 연구가 활발하다. 본 연구에서는 RF-Magnetron Sputtering법을 이용하여 $Ga_2O_3$ 혼합비에 따라 제작된 ZnO(GZO) 박막들의 전기적, 광학적, 구조적인 특성들을 분석하였다. 측정결과, $Ga_2O_3$의 첨가량이 7 wt.%인 GZO 박막이 가시광선영역에서 80%이상의 높은 투과율과 $50.5\;\Omega/\Box$의 가장 낮은 면저항을 나타내었다. 이는 Ga원소가 다른 3족 원소와 격자결합을 비교할 때, 이온의 크기가 Zn원소와 비슷하여 최적화된 혼합율을 가지는 경우 격자결합을 최소화시켜 캐리어 밀도의 증가로 인해 높은 전도성을 가지며, 고온에서도 전기적 특성 및 내구성이 향상되기 때문이다. 또한 기판온도에 따른 열처리 특성으로서 기판의 온도를 $100^{\circ}{\sim}400^{\circ}C$까지 변화를 주어 실험하였다. X-선 회절패턴 분석결과 기판온도가 증가함에 따라 ZnO (002) 방향이 감소하는 반면 ZnO(103) 방향이 증가하였으며, 기판온도가 $300^{\circ}C$ 일 때 $17.1\;\Omega/\Box$의로 가장 낮은 면저항이 나타났다. 이는 SEM 이미지를 분석한 결과, 실온에서 제작된 박막과 비교해 300 에서 증착된 GZO 박막이 결정립의 크기가 크고 밀도도 조밀해져 전하의 이동도가 향상되었기 때문이다.