• 한국정보통신설비학회:학술대회논문집
• /
• 2008.08a
• /
• pp.93-96
• /
• 2008

A transmitter (TX) leakage cancellation scheme using a Micro Controller Unit (MCU) is introduced. This paper highlights an adaptive anti-leakage signal generation via an MCU, which plays the key role in reducing the TX leakage signal level. High transmitter-to-receiver (TX-to-RX) isolation is verified with measurement results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.862-865
• /
• 2007

Rx and Tx signal use same band in RFID. Then RFID system is not used duplexer and used coupler. RFID system have problem about Rx part to Tx leakage signal because that Rx signal port is Tx signal port's Isolation port. We proposal using phase shifter Tx leakage signal decrease than other RFID system. It is same signal Tx signal port's coupling port and isolation port signal except amplitude and phase. So if make coupling signal and isolation signal is in all same signal. We cancel Tx leakage signal used coupling port. And verification about ADS2006.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.2
• /
• pp.43-49
• /
• 2008

In this paper, new directional couplers for T/R switch of UHF RFID applications are proposed to overcome TX-to-RX leakage problem. The proposed method can remove TX-to-RX leakage caused by both imperfect isolation characteristic of the conventional directional coupler and the mismatch of antenna impedance. Two directional couplers are implemented using distributed elements and lumped elements respectively for the verification. The varactor tuneable circuits for compensation of the antenna mismatch is also proposed. The measurement result shows excellent TX-to-RX leakage suppression, more than 45dB in 910MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.8
• /
• pp.784-789
• /
• 2011

In this paper, a tunable integrated transmitter leakage canceller based on an autotransformer for ultra-high-frequency (UHF) RFID readers is presented. The proposed TX leakage canceller consists of an autotransformer, a digital tuning capacitor, a voltage controlled tuning resistor, and a compensating amplifier, and it is designed using 0.13 ${\mu}m$ 1-poly 6-metal RF CMOS process. The simulation results show that the proposed structure has over 55 dB rejection characteristic between a transmitter and a receiver and a 2.5 dB of the RX insertion loss. The TX leakage canceller can be digitally tuned from 825 MHz to 985 MHz with the tuning capacitor and it can be fully integrated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.5A
• /
• pp.543-550
• /
• 2011

In order to improve readability, a leakage-signal canceller has been proposed in UHF-band RFID readers. The proposed canceller is composed of two blocks: an environment monitoring block for detection of Tx and RX power levels and a leakage cancellation block. The leakage canceller consists of directional-couplers, digital attenuators and phase shifters based on the feed-forward scheme. The leakage canceller is located between antenna and reader. An improved experimental characterization of the scheme is presented with results from the reader operating in the Korean RFID frequency band, conforming the validity of the approach with more than 29 dB of leakage cancellation.

• 한국ITS학회:학술대회논문집
• /
• v.2006 no.10
• /
• pp.321-324
• /
• 2006

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.370-375
• /
• 2011

In this paper, we propose an antenna module with high isolation between Tx and Rx in RFID reader module. The proposed module consists of a quadrafilar antenna and a directional coupler with a switchable dummy load to improve the directivity. The proposed module achieves the isolation higher than 20 dB between Tx and Rx. To show the validity of the proposed scheme, we have performed the measurement of tagging range and multi-tagging ability. The experiment results show that the detecting range and multi-tagging ability are enhanced by 81% and 200%, respectively.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.206-209
• /
• 2016

This letter proposes a reconfigurable directional coupler that uses a variable impedance mismatch reflector to achieve high isolation characteristics in the antenna front end. The reconfigurable coupler consists of a directional coupler and a single-pole four-throw (SP4T) switch with different load impedances as a variable load mismatch reflector. Selection of the load impedance by the reflector allows cancellation of the reflected signal due to antenna load mismatch and the leakage from the input to isolation port of the directional coupler, resulting in high isolation characteristics. The performance of the proposed architecture in separating the received (Rx) signal from the transmitted (Tx) signal in the antenna front end was verified by implementing and testing the reconfigurable coupler at 917 MHz for UHF radio-frequency identification (RFID) applications. The proposed reconfigurable directional coupler showed an improvement in the isolation characteristics of more than 20 dB at the operation frequency band.

• Journal of Satellite, Information and Communications
• /
• v.9 no.1
• /
• pp.90-96
• /
• 2014

This paper is about increasing transfer efficiency of wireless power transmission. The new method is proposed to detect the alignment of transmitter and receiver of wireless charger and so smart phone can display the position of wireless charging receiver on its LCD panel for the maximum charging efficiency. The previous method is only to show the transfer efficiency, but this method is to show not only the efficiency but also coordinates of receiver. The apparatus of the wireless charger is based on WPC(Wireless Power Consortium) standard and has planar air coil combined with magnet shield in Tx and Rx device so that the leakage flux is minimized on condition of under hundreds of kHz operating frequency. In this paper, it's showed that relation of magnet field and distance of each coils can be linearized and position information of Tx and Rx device is calculated thru trigonometry. Through the experiment, the obstacles of linearity are discovered and also showed that it can be optimized. and so the presented method is suitable for alignment detection method of Tx and Rx device in WPC wireless charger.

• Journal of electromagnetic engineering and science
• /
• v.9 no.1
• /
• pp.39-45
• /
• 2009

In this paper, we discuss hardware design and deployment issues in current passive UHF RFID systems. Using the link budget concept, the methodology to calculate forward- and reverse-link interrogation range is shown. Then, we consider hardware issues: phase diversity, phase noise with range correlation, and TX leakage problems. Finally, three interference problems when deploying RFID systems are presented.