• The Journal of Engineering Geology
• /
• v.21 no.1
• /
• pp.57-64
• /
• 2011

Three-dimensional slope stability analysis was applied to a failed dual-lithology slope containing both granite and an andesitic dyke, taking account of the differences in shear strength of the different lithologies. A direct shear test of the soil-rock boundary was performed to examine the shear strength of two different types of failure surfaces within different lithologies, and a laboratory test was performed on an upper, weathered soil layer. The test results indicate that shear strength was lower at the soil-rock boundary than within the weathered soil layer. A representative geological section was subjected to two-dimensional slope stability analysis using a limit equilibrium method to assess whether the distribution of lithologies upon the slope influences the results of stability analysis. The results were then compared with those of three-dimensional slope stability analysis, for which input parameters can be varied according to the distribution of lithologies upon the slope. The three-dimensional analysis yielded safety factors of 1.26 under dry conditions and 0.55 under wet conditions, whereas the two-dimensional analysis yielded unstable safety factors of 0.92 and 0.32, respectively. These findings show that the results of stability analysis are affected by the distribution of different lithologies upon the slope. Given that the studied slope collapsed immediately after rainfall, it is likely that the results of the three-dimensional analysis are more reliable.

• Geomechanics and Engineering
• /
• v.17 no.2
• /
• pp.181-194
• /
• 2019

Due to the seepage of groundwater, the resisting force of slopes decreases and the sliding force increases, resulting in significantly reduced slope stability. The instability of most natural slopes is closely related to the influence of groundwater. Therefore, it is important to study slope stability under groundwater seepage conditions. Thus, using a simplified seepage model of groundwater combined with the analysis of stresses on the slip surface, the limit equilibrium (LE) analytical solutions for two- and three-dimensional slope stability under groundwater seepage are deduced in this work. Meanwhile, the general nonlinear Mohr-Coulomb (M-C) strength criterion is adopted to describe the shear failure of a slope. By comparing the results with the traditional LE methods on slope examples, the feasibility of the proposed method is verified. In contrast to traditional LE methods, the proposed method is more suitable for analyzing slope stability under complex conditions. In addition, to facilitate the optimization of drainage design in the slope, stability charts are drawn for slopes with different groundwater tables. Furthermore, the study concluded that: (1) when the hydraulic gradient of groundwater is small, the effect on slope stability is also small for a change in the groundwater table; and (2) compared with a slope without a groundwater table, a slope with a groundwater table has a larger failure range under groundwater seepage.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.620-625
• /
• 2009

The seismic slope stability is most often evaluated by the pseudo-static limit analysis, in which the earthquake loading is simplified as static inertial loads acting in horizontal and/or vertical directions. The transient loading is represented by constant acceleration via the pseudostatic coefficients. The result of a pseudostatic analysis is governed by the selection of the value of the pseudostatic coefficient. However, selection of the value is very difficult and often done in an ad hoc manner without a sound physical reasoning. In addition, the maximum acceleration is commonly estimated from the design guideline, which cannot accurately estimate the dynamic response of a slope. There is a need to perform a 2D dynamic analysis to properly define the dynamic response characteristics. This paper develops the modified one-dimensional seismic site response analysis. The modified site response analysis adjusts the density of the layers to simulate the change in mass and weight of the layers of the slope with depth. Multiple analyses are performed at various locations within the slope to estimate the change in seismic response of the slope. The calculated peak acceleration profiles with depth from the developed procedure are compared to those by the two-dimensional analyses. Comparisons show that the two methods result in remarkable match.

• Geomechanics and Engineering
• /
• v.14 no.1
• /
• pp.71-81
• /
• 2018

Soils are mostly nonhomogeneous and anisotropic in nature. In this study, nonhomogeneity and anisotropy of soil are taken into consideration by assuming that the cohesion increases with depth linearly and also varies with respect to direction at a particular point. A three-dimensional rotational failure mechanism is adopted, and then a three-dimensional stability analysis of slope is carried out with the failure surface in the shape of a curvilinear cone in virtue of the limit analysis method. A quasistatic approach is used to develop stability charts in nonhomogeneous and anisotropic soils. One can easily read the safety factors from the charts without the need for iterative procedures for safety factors calculation. The charts are of practical importance to prevent a plane failure in excavation slope whether it is physically constrained or not. Then the most suitable location of piles within the reinforced slope in nonhomogeneous and anisotropic soils is explored, as well as the interactions of nonhomogeneous and anisotropic coefficients on pile reinforcement effects. The results indicate that piles are more effective when they are located between the middle and the crest of the slope, and the nonhomogeneous coefficient as well as the anisotropic coefficient will not only influence the most suitable location for piles but also affect the calculated safety factor of existing reinforced slope. In addition, the two coefficients will interact with each other on the effect on slope reinforcement.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.34-34
• /
• 2012

Heavy storms rainfall has caused many landslides and slope failures especially in the mountainous area of the world. Landslides and slope failures are common geologic hazards and posed serious threats and globally cause billions in monetary losses and thousands of casualies each year so that studies on slope stability and its failure mechanism under rainfall are being increasing attention of these days. Rainfall-induced slope failures are generally caused by the rise in ground water level, and increase in pore water pressures and seepage forces during periods of intense rainfall. The effective stress in the soil will be decreased due to the increased pore pressure, which thus reduces the soil shear strength, eventually resulting in slope failure. During the rainfall, a wetting front goes downward into the slope, resulting in a gradual increase of the water content and a decrease of the negative pore-water pressure. This negative pore-water pressure is referred to as matric suction when referenced to the pore air pressure that contributes to the stability of unsaturated soil slopes. Therefore, the importance is the study of saturated unsaturated soil behaviors in evaluation of slope stability under heavy rainfall condition. In an actual field, a series of failures may occur in a slope due to a rainfall event. So, this study attempts to develop a numerical model to investigate this failure mechanism. A two-dimensional seepage flow model coupled with a one-dimensional surface flow and erosion/deposition model is used for seepage analysis. It is necessary to identify either there is surface runoff produced or not in a soil slope during a rainfall event, while analyzing the seepage and stability of such slopes. Runoff produced by rainfall may result erosion/deposition process on the surface of the slope. The depth of runoff has vital role in the seepage process within the soil domain so that surface flow and erosion/deposition model computes the surface water head of the runoff produced by the rainfall, and erosion/deposition on the surface of the model slope. Pore water pressure and moisture content data obtained by the seepage flow model are then used to analyze the stability of the slope. Spencer method of slope stability analysis is incorporated into dynamic programming to locate the critical slip surface of a general slope.

• Journal of Industrial Technology
• /
• v.1
• /
• pp.17-25
• /
• 1981

Past research has concentrated on refining two-dimensional analysis techniques. Rather extensive comparisons of various two-dimensional methods have been made. This paper described a general three-dimensional method of analysis by which any geometrical condition and any c, phi soil can be analyzed. The results are as follows; 1. Factors of safety computed for 3-dimensional geometry differ considerably from ordinary 2-dimensional factors of safety. 2. 3-dimensional factors of safety are generally much higher than 2-dimensional factors of safety. However, situations appear to exist where the 3-dimensional factor of safety can be lower than the 2-dimensional factor of safety. 3. The F3/F2 ration appears to be quite sensitive to c, phi and to the slope.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.1
• /
• pp.47-52
• /
• 2015

In the slope stability analysis and design, Limit Equilibrium Method (LEM) and Shear Strength Reduction technique (SSR) are mainly used. Both methods are able to perform two and three dimensional analysis. SSR is considered to be more sensitive and more reasonable than LEM by many researchers. However, in practice LEM is still widely used because of the increase of analysis time and complexity of the model in SSR. In this study, three dimensional analysis of the protruding rock slope is performed by SSR in order to study the effects of protruding length using rock slope FLAC 3D. In this study, as results of analysis variations of the safety factor have been studied according to slope angle, slope height, the soil strength, protruding slope length projected variables. The results show that the factor of safety as more affected by the shapes of the protruding rock slope than the rock strength.

• Journal of the Korean Professional Engineers Association
• /
• v.18 no.3
• /
• pp.21-27
• /
• 1985

Earthen mass located beneth a sloping group surface, whether natural or manmade, have a tendency to move downward and outward under the influence of gravity. Unless this tendency is suitably counteracted by the Shearing resistances within the mass, a landslide occurs. Avoiding such instabilities is a major concern of the geotechnical engineer. The shearing behavior of a soil is determined empirically, i.e., by field tests or laboratory tests. This results are applied to the slope stability analysis. The factor of safety for slope stability analysis is much more sensitive to the choice of strength parameters as interpreted from soil tests than to the choice of the computational method of analysis. This paper was investigated the influence of the change in the factor of safety due to a change in one of the parameters, relative to the total change in the factor of safety due to change in all parameters. A conclusion may be reached with respect to the required precision definition of the different variables to limit uncertainties in the factor of safety to tolerable levels.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.399-404
• /
• 2008

The influence of gas hydrate dissociation on submarine slope stability was studied in this paper. Gas hydrates are stable under high pressure and low temperature conditions. Once gas hydrate dissociates due to natural or human activities, it generates large amount of gas and water. During gas hydrate dissociation, a pore pressure between soil particles increases and results in the loss of an effective stress and degradation of soil stiffness. A pore pressures model was proposed to calculated excess pore pressures generated by gas hydrate dissociation at the Storegga Slide. A slope stability analysis for the Storegga Slide using a two dimensional finite difference method was carried out by considering excess pore pressures due to gas hydrate dissociation. Since the excess pore pressure calculated by the proposed method resulted in the considerable loss of stiffness and strength in slope, a submarine slope failure occurred at the Storegga slide was well simulated.

• Tunnel and Underground Space
• /
• v.8 no.1
• /
• pp.37-45
• /
• 1998

In this study, two dimensional and three dimensional numerical analysis were performed with a finite difference code for the safe maintenance of the spillway slope of the Boryeong dam. Results of the geological survey and the stereographic projection analysis on the discontinuities were used as input data for the numerical analysis. As a result, several suggestions were given such as the reinforcement of the local tension zone, the decrease in the angle of the slope, the drawdown of the pore pressure in the slope and the removal of the upper benches. A systematic and long-term monitoring system was also suggested.