• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.2
• /
• pp.221-226
• /
• 2012

In this paper, wideband two-stage amplification stage was designed, fabricated and evaluated. The proposed amplification stage with a novel gain control method have a high gain, low noise and high linearity performance. It is consisted of common emitter amplifier as the first stage, cascode gain control amplifier as second stage and power detector which sense the received signal strength. The proposed amplification stage shows a total gain of 29 dB~37 dB, noise fiugre of 1.5 dB at operating band and high linearity performance as the IMD (third intermodulation distortion) level is below the noise level of the measurement equipment at the control voltage 2.0 V generated from power detector under the strong electric field condition.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.336-343
• /
• 2011

This paper introduces a simple variable gain amplifier (VGA) structure that shows an inherently dB-linear gain control property. Requiring no additional components for dB-linear control, the structure is compact and power efficient. The designed two-stage VGA shows a gain control range of 60dB with the gain error in the range of ${\pm}0.4$ dB. The power consumption including the output buffer is 20.4 mW from 1.2 V supply voltage with bandwidth of 630 MHz. The prototype was fabricated in a 0.13 ${\mu}m$ CMOS process and the VGA core occupies 0.06 $mm^2$.

• ETRI Journal
• /
• v.45 no.4
• /
• pp.690-703
• /
• 2023

Multistage amplifiers have become appropriate choices for high-speed electronics and data conversion. Because of the large number of high-impedance nodes, frequency compensation has become the biggest challenge in the design of multistage amplifiers. The new compensation technique in this study uses two differential stages to organize feedforward and feedback paths. Five Miller loops and a 500-pF load capacitor are driven by just two tiny compensating capacitors, each with a capacitance of less than 10 pF. The symbolic transfer function is calculated to estimate the circuit dynamics and HSPICE and TSMC 0.18 ㎛. CMOS technology is used to simulate the proposed five-stage amplifier. A straightforward iterative approach is also used to optimize the circuit parameters given a known cost function. According to simulation and mathematical results, the proposed structure has a DC gain of 190 dB, a gain bandwidth product of 15 MHz, a phase margin of 89°, and a power dissipation of 590 ㎼.

• 전기의세계
• /
• v.30 no.9
• /
• pp.582-588
• /
• 1981

The laser parameters such as a population inversion density, a stimulated emission cross section and loss factor in the glass laser amplifier medium were experimentally determined in order to analyse the properties of laser amplification. Using these parameters, the rate equations were approximately solved and the properties of laser amplification were analysed. An experiment of two-stage amplifier of Q-switching laser pulse was performed and the maximum output power was 1.1 GW, 33J. The several problems such as a laser solarization and a laser coupling in laser amplification were resolved.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.719-725
• /
• 2019

We propose a 2.4-GHz CMOS power amplifier (PA) with a bypass structure to improve the power-added efficiency (PAE) in the low-power region. The primary winding of the output transformer is split into two parts. One of the primary windings is connected to the output of the power stage for high-power mode. The other primary winding is connected to the output of the driver stage for low-power mode. Operation of the high power mode is similar to conventional PAs. On the other hand, the output power of the driver stage becomes the output power of the overall PA in the low power mode. Owing to a turning-off of the power stage, the power consumption is decreased in low-power mode. We designed the CMOS PA using a 180-nm RFCMOS process. The measured maximum output power is 27.78 dBm with a PAE of 20.5%. At a measured output power of 16 dBm, the PAE is improved from 2.5% to 12.7%.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.768-776
• /
• 2014

Using a simplified high-frequency small-signal equivalent circuit model for BSIM3 MOSFET, the fully differential two-stage folded-cascode CMOS operational amplifier is analyzed to obtain its small-signal voltage transfer function. As a result, the expressions for dc gain, five zero frequencies, five pole frequencies, unity-gain frequency, and phase margin are derived for op amp design using design equations. Then the analysis result is verified through the comparison with Spice simulations of both a high speed op amp and a low power op amp designed for the $0.13{\mu}m$ CMOS process.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.3
• /
• pp.232-238
• /
• 2008

In this paper, a wideband power efficient 2.2 GHz - 4.9 GHz Medium Power Amplifier (MPA), has been designed and fabricated using $0.8{\mu}m$ SiGe BiCMOS process technology. Passive elements such as parallel-branch spiral inductor, metal-insulator-metal (MIM) capacitor and three types of resistors are all integrated in this process. This MPA is a two stage amplifier with all matching components and bias circuits integrated on-chip. A P1dB of 17.7 dBm has been measured with a power gain of 8.7 dB at 3.4 GHz with a total current consumption of 30 mA from a 3 V supply voltage at $25^{\circ}C$. The measured 3 dB bandwidth is 2.7 GHz and the maximum Power Added Efficiency (PAE) is 41 %, which are very good results for a fully integrated Medium PA. The fabricated circuit occupies a die area of $1.7mm{\times}0.8mm$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.4
• /
• pp.403-409
• /
• 2013

In this work, a CMOS two stage differential power amplifier which includes Marchand balun, transformer and injection-locked buffer is presented. The power amplifier is targeted for 70 GHz frequency band and fabricated using 65 nm technology. The measurement results show 8.5 dB maximum voltage gain at 71.3 GHz and 7.3 GHz 3 dB bandwidth. The measured maximum output power is 8.2 dBm, input $P_{1dB}$ is -2.8 dBm, output $P_{1dB}$ is 4.6 dBm and maximum power added efficiency is 4.9 %. The power amplifier consumes 102 mW DC power from 1.2 V supply voltage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.8
• /
• pp.1465-1470
• /
• 2006

This paper presents a design of low power CMOS LNA(Low Noise Amplifier) for 2.4 GHz ZigBee applications that is a promising international standard for short area wireless communications. The proposed circuit has been designed using TSMC $0.18{\mu}m$ CMOS process technology and two stage cascade topology by current reuse technique. Two stage cascade amplifiers use the same bias current in the current reused stage which leads to the reduction of the power dissipation. LNA design procedures and the simulation results using ADS(Advanced Design System) are presented in this paper. Simulation results show that the LNA has a extremely low power dissipation of 1.38mW with a supply voltage of 1.0V. This is the lowest value among LNAs ever reported. The LNA also has a maximum gain of 13.38dB, input return loss of -20.37dB, output return loss of -22.48dB and minimum noise figure of 1.13dB.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.321-328
• /
• 2008

In this paper, variable gain amplifier(VGA) with a gain slope controller has been proposed and verified by circuit simulations and measurements. The proposed VGA has a gain control, gain slope switch and variable gain range. The input source coupled pair with diode connected load is used for VGA gain stage. The gain slope controller with switch can control VGA gain slope. The proposed VGA is fabricated in $0.18{\mu}m$ CMOS process for multi -standard wireless receiver. The proposed two stage VGA consumes min. 2.0 mW to max. 2.6 mW in gain control range and gives input IP3 of -3.77 dBm and NF of 28.7 dB at 1.8 V power supply under -25 dBm, 1 MHz input. The proposed VGA has 37 dB(-16 dB $\sim$ 21 dB) variable gain range, and 8 dB gain range control per 0.3 V control voltage, and can provide variable gain, positive and negative gain slope control, and gain range control. This VGA characteristics provide design flexibility in multi-standard wireless receiver.