• International Journal of Fluid Machinery and Systems
• /
• 제4권1호
• /
• pp.97-103
• /
• 2011

With the aim to increase blade loadings and stable operating range in highly loaded compressors, this article has been conducted to explore, through a numerical parametric study, the potential of passive control using slotted bladings in cascade configurations. The objective of this numerical investigation is to analyze the influence of location, width and slope of the slots and therefore identify the optimal configuration. The approach is based on two dimensional cascade geometry, low speed regime, steady state and turbulent RANS model. The results show the efficiency of this passive technique to delay separation and enhance aerodynamic performances of the compressor cascade. A maximum of 28.3% reduction in loss coefficient have been reached, the flow turning is increased with approximately $5^0$ and high loading over a wide range of angle of attack have been obtained for the optimized control parameter.

• 제어로봇시스템학회논문지
• /
• 제12권12호
• /
• pp.1197-1201
• /
• 2006

In order to improve the operability in a fully thermally coupled distillation column the main column is separated into an upper and a lower column, and its design method is explained. With a distillation experiment using a two-inch column the operability of the proposed column is examined. Readily available methanol, ethanol and propanol are used as the feed, and the experimental result is compared with that of the HYSYS simulation. It is found from the experiment that the recovery ranges between 58.8% and 68% and the distillation efficiency is lower than that of the simulation. consumes less energy than an original column, it is not widely implemented in practice due to its operational difficulty. However, it is proved that the proposed distillation column can be operated without compressors and it can be practically utilized.

• 설비공학논문집
• /
• 제11권6호
• /
• pp.716-724
• /
• 1999

In co-orbiting scroll compressor, the two scroll members are to orbit with independent radii, producing a relative orbit motion between them. One scroll member is driven by the crank mechanism while the motion of the other member is determined by geometrical constraints and reacting forces. This paper presents an analytical study on the performance of a co-orbiting scroll compressor. The following results have been obtained: Radial contact force between the scroll wraps is virtually free from the centrifugal force of the orbiting scroll member. The frictional losses are somewhat increased due to the complicated drive mechanism, yielding to a little lower EER compared to conventional radially compliant scroll compressors .

• 한국정밀공학회지
• /
• 제33권8호
• /
• pp.635-640
• /
• 2016

The shell body is the main exterior part of a compressor, and production of shell bodies has increased along with a growing demand for air conditioners, refrigerators, air compressors, and so on. Cracks frequently occur in the process of welding a shell body. In this study, a deep drawing process for creating a shell body from a blank is developed. The technique consists of a four-step deep drawing and a two-step trimming process. Analysis is performed by DEFORM software to examine the safety of the deep drawing and trimming processes. The deep drawing process for the shell body developed in this study would have wide application in many industrial fields.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.138-144
• /
• 1997

The analysis of lateral hydrodynamic forces from the compressor labyrinth seals is presented. The basic equations are derived using a two-control-volume model for compressible flow. Blasius' wall friction-factor formula and jet flow theory are used for the calculation of the wall shear stresses and the recirculation velocity in the cavity. Linearized zeroth-order and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. Integration of the resultant first-order pressure distribution along and around the seal defines the rotordynamic coefficients of the labyrinth seal. The rotordynamic analysis for the balance drum labyrinth seal of an ethylene refrigeration compressor is carried out. The results of rotordynamic characteristic of the labyrinth seal and comparisons with other types of seal, honeycomb seal and smooth seal, are presented.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.66-71
• /
• 2008

Two cases with circumferential grooves were designed for a transonic compressor, and 3-D numerical simulations were conducted for stall mechanism at three representative speeds. A conclusion can be drawn from the comparison between compressors with or without casing treatment that: with the rising of rotation speed, stall margin increases dramatically under the help of casing treatments, and the case with middle grooves has reasonable compromise between stall margin increment and efficiency cutting. At lower speed, the increment reduces, and grooves at the back of blade tip have more influence on stall margin. Further investigation shows there is a transition in mechanism of compressor stall with the decline of rotational speed: at high rotation speed, the expansion of stall margin mainly results from the suppression of tip leakage vortex by casing treatments, yet it benefits more from the depression of boundary layer separation from suction surface of blade tip.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.403-408
• /
• 2001

Structure-borne noise and vibration is one of the main complaints of home appliances such as refrigerators, washing machines, air conditioners, etc. There have been many efforts to reduce the emitting noise and vibration. Mostly the efforts have been concentrated to optimize the mounts shape and its material properties realizing that the vibration power is mainly transmitted to the structure via mounts. It is known that softer mounts have the better vibration isolation effect. But mounts have another important function in addition to the vibration isolation. That is to support the motor and compressor safely. Thus mounts should be stiff enough to resist the supporting items. But the two properties, stiff and soft, are contradict each other. So the designer should compromise the two complicity properties properly in between. Noticing that, motors and compressors themselves are very quite until they are connected to the base structure via mounts, wire connecting idea was proposed in this work. Instead of using conventional mounts, as shown in Fig 4, compressor was mounted using six wires as shown in Fig 5. Since wire is very flexible in bending but stiff in tension, we can realize the ideal mount design requirements, stiff enough to support and soft enough to isolate vibration power. The suggesting idea was tested with an air conditioner outdoor unit.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.1240-1246
• /
• 2006

일반적으로 전동차 보조전원장치의 출력전원 품질에 영향을 주는 주된 요인으로는 짧은 시간동안의 진폭변조로 인한 전압플리커 현상과 전동차 내부의 공기압축기 및 냉난방 환기장치 등 대용량 전동기의 반복적인 구동 등을 들 수 있다. 본 연구는 전동차내의 형광등의 전원과 관련된 플리커 현상에 대해 내장재 개조 후 형광등 32W와 개조 전 40W를 입력전원(AC220V)의 변동에 따른 광 출력(밝기) 로서 계측 비교하였다. 또한, 전압변동을 유발하는 부하변동의 주된 요인을 파악하기 위해 전동차 운행시간과 운행밀도를 고려하여 플리커 현상을 분석하였다. 연구결과, 개조 후 형광등 32W에 비해 40W 형광등이 입력전원의 변화에 대해 육안인식정도 측면에서는 20.26% 정도 덜 민감하게 반응함을 알 수 있었으며, 심한 플리커가 일어나는 전압의 경우도 19.9%로 더 낮게 측정되었다. 또한, 운행차량의 부하변동 영향에 있어서는 주로 영업차량의 운행밀도가 높고, 이용승객이 많은 혼합시간대에 보조전원장치(SIV)의 출력전압 변동으로 인한 객실형광등 플리커가 발생된다는 사실을 확인할 수 있었다. 더불어, 전동차 이용승객이 육안으로 형광등의 깜박임을 민감하게 느낄 수 있는 가능 주파수대역으로서 $8Hz{\sim}15Hz$ 임을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권1호
• /
• pp.46-52
• /
• 2010

본 논문에서는 천연가스 액화 플랜트 산업에서의 경쟁력 확보를 위한 핵심기술인 2단 압축 인터쿨러 방식을 적용한 액화공정에 대해 시뮬레이션을 수행하였다. 이 공정들은 기본 케스케이드 공정을 기초로 하였으며, 모든 공정에 2단 압축 방식을 적용하였다. 먼저 프로판, 에틸렌, 메탄 사이클에 각각 인터쿨러를 적용하였으며 성능 특성을 비교하였다. 모든 사이클에 인터쿨러를 적용한 공정의 COP가 13.7 ~ 20.5%로 가장 크게 증가하였고, LNG 단위 생산량 당 소요 에너지는 기본 케스케이드 공정에 비해 23.8% ~ 35%로 가장 크게 감소하였다.

• Journal of Mechanical Science and Technology
• /
• 제20권9호
• /
• pp.1390-1398
• /
• 2006

A gerotor pump is suitable for oil hydraulics of machine tools, automotive engines, compressors, constructions and other various applications. In particular the pump is an essential machine element that feeds lubricant oil in an automotive engine. The subject of this paper is the theoretical analysis of internal lobe pump whose the main components are the two rotors. Usually the outer one is characterized by lobes with a circular shape, while the inner rotor profile is determined as a conjugate to the other. For this reason the first topic presented here is the definition of the geometry of the rotors starting from the design parameters. The choice of these parameters is subject to some limitations in order to limit the pressure angle between the rotors. Now we will consider the design optimization. The first step is the determination of the instantaneous flow rate as a function of the design parameter. This allows us to calculate three performance indexes commonly used for the study of positive displacement pumps the flow rate irregularity, the specific flow rate, and the specific slipping. These indexes are used to optimize the design of the pump and to obtain the sets of optimum design parameter Results obtained from the analysis enable the designer and manufacturer of the oil pump to be more efficient in this field.