• Journal of Korean Association for Spatial Structures
• /
• v.8 no.3
• /
• pp.91-99
• /
• 2008

As number of the buildings increases, it shows new trends such as twisted, tilted, taperer shape. As a structural solution for the new trend buildings, diagonal grid (Diagrid) structure was developed. Though a few buildings was built using diagird system, the structural performance of the corresponding node was not clearly identified. Therefore, experimental evaluation is needed to apply diagrid for higher buildings. In this study, the node was tested depending on the amounts of welding materials. As a result, the partial welding can provide enough strength for the node as required in the full penetration welding under monotonin compressive loadings.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.1
• /
• pp.85-93
• /
• 1988

Installation of the digital carrier system is increased rapidly in the telecommunication network, and most of systems are operating over a twisted pair conductor. Many systems are accommodated in multipair cable for their economical installation, therefore we must consider tha crosstalk interference between digital systesm. This paper considers the calculation method which determine crosstali interference between signals in multipair. And the transmission margin at a certain error rate is analyzed considering crosstalk power. Finally, this paper estimates the crosstalk noise susceptibility of 2.048Mbps relative to 1.544Mbps PCM system and 1.544Mbps relative to 2.048Mbps PCM system, and then considers the methos which both systems can operate together in a same cable.

• Journal of the Korean Ceramic Society
• /
• v.37 no.4
• /
• pp.345-353
• /
• 2000

Carbon nanofibers were prepared from the decomposition of various carbon-containing gases over pure Ni, pure Fe and their alloys with Cu. They yields, properties, and structure of carbon nanofibers obtained from the various reaction conditions were analyzed. Type of reacting gas, reaction temperature and catalyst composition were changed as the reaction variable. With Ni-Cu catalysts, the maximum yields of carbon nanofibers were obtained at temperatures between 550 and 650$^{\circ}C$ according to the reacting gas mixtures of C2H2-H2, C2H4-H2 and C3H8-H2, and the surface areas of the carbon nanofibers produced were 20∼350㎡/g. In the case of CO-H2 mixture, the rapid deposition of carbon nanofibers occurred with Fe-Cu catalyst and the maximum yield were obtained around 550$^{\circ}C$ with the range of surface areas of 140∼170㎡/g. The electrical resistivity of carbon nanofiber regarded as the key property of filler for the application of electromagnetic interference shielding was very sensitive to the type of reactant gas and the catalyst composition ranging 0.07∼1.5Ωcm at a pressure of 10000 psi, and the resistivity of carbon nanofibers produced over pure nickel catalyst were lower than those over alloy catalysts. SEM observation showed that the carbon nanofibers produced had the diameters ranging 20∼300 nm and the straight structure of carbon nanofibers changed into the twisted or helical conformation by the variation of reacting gas and catalyst composition.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37A no.12
• /
• pp.1115-1121
• /
• 2012

In this paper, the design of UTP LAN cable with enhanced alien crosstalk characteristic is proposed. Proposed LAN cable is made with jacket of the irregularly corrugation type. If necessary, it is possible to use the special cross-filler. The alien crosstalk characteristic is enhanced by using proposed cable with inner jacket of the irregularly corrugation type in wide frequency band. The design of the cable was based on parameters of the standard EIA/TIA 568-B.2-10.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.6
• /
• pp.622-632
• /
• 2004

We have studied how liquid crystal's rubbing direction and voltage driving method affect generation of disclination line. At first, generation of disclination line in vertical alignment(VA) cell and VA-twisted nematic(TN) cell has been examined. When liquid crystal's rubbing direction of bottom substrate was 0$^{\circ}$, the degree of generated disclination line was the smallest value. Further, the generation of disclination line above the electrode is less in the frame inversion than in the line inversion. Secondly, we have examined a generation of disclination line in reflective fringe-field switching cell. When the distance between common electrodes is over 3 ${\mu}{\textrm}{m}$ with on-state of one pixel and off-state of neighboring pixels, the reflectance appears only on-state pixel without generating reflectance in adjacent pixels.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.3
• /
• pp.241-246
• /
• 2000

We fabricated Bi-2223 multi-filaments superconductor tape and evaluated the effect of twisting on the microstructural evolution and critical current. Twist pitches of the tapes are in the range of 70- 8mm and uniformly deformed. It was observed that grain size and the degree of texture decreased as decreasing pitch probably due to the formation of the irregular interface between Ag and filaments. In addition critical current of the tapes decreased to 6.5 A with decreasing pitch to 8mm, showing 48% of degradation compared to the untwisted tapes decreased to 6.5 A with decreasing pitch to 8mm, showing 48% of degradation compared to the untwisted tape(12.5 A). These reduction of critical current may be related to the interface irregularity smaller grain size worse texture and the presence of cracks due to the induced strain during twisting processing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.400-400
• /
• 2007

In this study, we investigated liquid crystal (LC) alignment with ion beam (IB) that non contact alignment technique on polyimide and electro-optical characteristics of twisted nematic (TN)-liquid crystal display (LCD) on the polyimide under various ion beam angles. In this experiment, polyimide layer was coated on glass by spin-coating and Voltage-transmittance(VT) and response time characteristics of the TN cell were measured by a LCD evaluation system. The good characteristics of the nematic liquid crystal (NLC) alignment with the ion beam exposured polyimide surface was observed. In addition, it can be achieved the good EO properties, and residual DC property of the ion beam aligned TN cell on polyimide surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.62-65
• /
• 2005

We studied the nematic liquid crystal (NLC) alignment capability by the Ultraviolet (UV) alignment method on a-C:H thin-films, and investigated electro-optical performances of the UV aligned twisted nematic (TN)-liquid crystal display (LCD) with the UV exposure on a-C:H thin film surface. A good LC alignment by UV irradiation on a-C:H thin-film surfaces was achieved. Monodomain alignment of the UV aligned TN-LCD can be observed. The good electro-optical (EO) characteristics of the UV aligned TN-LCD was observed with oblique UV exposure on the a-C:H thin film surface for 1min.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.185-188
• /
• 2005

We synthesized the two types of photoalignment material of high thermal resistance with hydroxyl aromatic polyimide, and studied the liquid crystal (LC) aligning capabilities on the photopolymer layers. Also, electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure were investigated. A good LC alignment with UV exposure on the two types of photopolymer surface can be obtained. The Voltage-transmittance (V-T) curve in the photoaligned TN cell with UV exposure was different from two type. The response time of photoaligned TN cell was measured about 21 ms in two alkyl chain and about 15ms in four alkyl chain.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.5
• /
• pp.198-201
• /
• 2008

The electro-optical (EO) characteristics of the one-side rubbing twisted nematic (TN) - liquid crystal display (LCD) on the polyimide (PI) surface with one-side ion beam (IB) irradiation were successfully studied. The good LC alignment for the one-side rubbing TN-LCD on the PI surface with one-side IB irradiation was observed. The suitable transmittance-voltage curves for the one-side rubbing TN-LCD on the PI surface with one-side IB irradiation were measured. Also, the good response time characteristics of the one-side rubbing TN-LCD on the PI surface with one-side IB irradiation were measured. The fast response time can be achieved for the one-side rubbing TN-LCD on the PI surface with one-side IB irradiation.