• 한국기계가공학회지
• /
• 제11권2호
• /
• pp.79-84
• /
• 2012

This study consist of two parts. One is development of a self-propelling vinyl remover which was already reported at the previous paper. This is the second part of the study. For the study, an attached vinyl remover was developed. It was consisted of connecting tractor to bucket, removing bucket from tractor, and the process was the tractor's assistance hydraulics. In the case of an attached vinyl remover, the vinyl was twisted 0.5times per 30~85cm length. The bobbin's diameter was 190mm and it's stable travelling speed was 1m/s. The revolution of the remover wheel was 90rpm to maintain the wheel's linear velocity. As seen at performance test at the field which had 950mm ridge intervals and 10 a area, the average working speed was 1m/s and the turning time was 20seconds. Therefore, the working performance was 24.5min/10a. The efficiency of used vinyl remover was 97% and working conditions were good.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(II)
• /
• pp.857-862
• /
• 2002

철도차량의 주행장치는 비틀림 선로를 주행할 경우 윤중감소가 발생하게 되며 이 값은 모든 하중 조건 및 공기스프링의 충기/배기 상태에서 UIC/ORE 보고서에서 규정한 기준치 60% 이내를 준수하여야만 한다. 이 논문은 인도 DMRC 전동차를 대상으로 시험을 실시하여 DMRC 선로 중 최악의 조건에서 UIC / ORE 에서 규정하고 있는 차량의 윤중감소율( Wheel Off-loading)의 기준을 만족하는 지에 대한 평가한 것을 기술하였다.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.113-118
• /
• 2012

Mulching vinyl is used on field crops to reduce herbicides and this causes multiple effects. The mulching vinyl must be collected for the next crop season, but was left alone due to a shortage of labor. The used mulching vinyl that was left alone acted as one of the main sources of environmental pollution on farms. In order to solve these problems, a self-propelling vinyl remover was developed. The self-propelling vinyl remover consists of a travelling part and rotating of remover wheel. Each output device has a 1.5ps engine and a 2.5ps engine. The vinyl was twisted 17~47cm/times length. The bobbin's diameter was 160mm and it's stable travelling speed was 0.5m/s. The revolution of the remover wheel bobbin was 60rpm to maintain the wheel's linear velocity. As seen at performance test at the field which had 950mm ridge intervals and 10a area, the average working speed was 0.56m/s and the turning time was 15seconds. Therefore, the working performance was 40.1min/10a.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.299-307
• /
• 2005

The 180 km/h Korean Tilting Train(TTX) which is now developing as a part of the Korean National R&D project, was elaborately designed. As the tilting trains run curve track with the $30\%$ higher speed than normal trains, the higher centrifugal and dynamic force are expected. Furthermore the complex tilting system increase the probability of failure. Therefore it is very important for tilting train to ensure safety against derailment under the various kind of failed condition in the middle of running as well as normal operating condition. The TTX train have the relatively high roll stiffness to improve the lateral ride comfort and to limit the roll displacement on the curve. But the higher roll stiffness increase the risk of derailment on the twisted track. This paper describes the study to review the safety against derailment caused by the wheel unloading on the severely twisted track. The worst combination of maximum cant change with maximum twist defect was established by numerical simulation. And also it was assumed that the air bag deflated and still the train run its speed limit. Those kind of assumption might be the worst case from the view point of wheel unloading derailment on the twisted track. The dynamic simulation was done by means of VAMPIRE S/W and non-linear transient analysis. We found that derailment quotients Q/P was only slightly influenced by track twist but the wheel unloading was greatly influenced. And we ascertained that the higher roll stiffness the higher wheel unloading. In case of air bag deflated situation, the wheel unloading reached up to $100\%$ which means the wheel lift or jumped. Therefore it was concluded that the design need to be improved to ensure the safety against derailment on the maximum twisted track in case of air bag deflated and tilting train's speed limit.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.635-640
• /
• 2000

This paper presents the analysis method of the instantaneous screw axis using line geometry in bump and rebound motion of 5-SS multi-link suspensions. Instantaneous screw axis is based on screw motion, and screw motion of zero pitch can be expressed as $Pl{\ddot{u}}cker$ line coordinates of line geometry instead of screw coordinates. In screw coordinates, twist and wrench are described by components of instantaneous screw axis. For instantaneous motion of wheel assembly, the principle of virtual work with twist and wrench is applied to 5-SS multi-link suspension, and it makes 5 linear equations. Therefore, it is possible to find instantaneous screw axis by solving these equations. This analysis by line geometry demands geometric values only, such as the locations of spherical joints in the case of multi-link suspensions.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1643-1653
• /
• 1994

To facilitate the manufacturing of dull using CNC grinding machine, the simulation of helical groove machining with given wheel profile and setting condition is necessary. Considering the wheel as a collection of thin disks, the flute configuration is predicted in a cross section perpendicular to the axis and the grinding wheel profile is also predicted to machine the desired helical groove with given setting conditions. Two programs for these processes are developed. Using programs interactively, the helical groove machining process can be predicted more accurately. By clarifying the geometrical relation between the shape of cutting edge and the flute configuration in the cross section which is perpendicular to drill axis, it becomes possible to predict the necessary cross sectional shape of wheel for desired drill cutting edge shape. Some factors for the software are considered concerning prediction of accuracy and computing time.

• 한국철도학회논문집
• /
• 제20권3호
• /
• pp.320-328
• /
• 2017

철도차량에 폭 넓게 적용되고 있는 축상고무스프링의 노화에 따른 탈선안전도 영향을 분석하고자 노화 축상고무스프링 시료를 대상으로 특성시험을 수행하였다. 그리고 축상고무스프링 노화가 탈선 안전에 미치는 영향을 분석하기 위하여 주행 동특성 해석을 수행하였다. 사용연수 17년이 지난 롤고무 축상스프링 시료를 대상으로 한 상하방향 특성시험결과, 고무 노화로 인하여 변위 복원기능이 저하되었고 스프링강성이 현저히 증가하였다. 그리고 EN14363규격 적용 twist궤도 주행 시를 모사한 주행동특성 해석결과, 정상 차량모델(Case1)에 비하여 노화 축상스프링 특성을 적용한 차량모델(Case2)의 탈선계수와 윤중감소가 증가하여 탈선안전도는 저하하였다. 특히 급격한 선형 변동이 발생하는 천이구간 주행 시 윤중감소로 인한 탈선안전도는 취약하게 나타났다.

• 한국철도학회논문집
• /
• 제14권1호
• /
• pp.57-65
• /
• 2011

교량을 주행하는 열차의 주행안전성과 승차감의 확보를 위해 Eurocode, 신간선 기준, 호남고속철도 설계지침 등에서는 교량의 연직변위, 연직가속도, 면틀림 등의 항목으로 제한하고 있다. 그러나 이와 같은 제한 기준은 교량 설계자의 편의를 위한 간접적인 방법이다. 또한 이와 같은 기준은 일반적인 경간(Eurocode의 경우 120m 이하)에 대한 제한 기준으로서, 이 이상의 장경간 교량의 경우에는 교량/열차 상호작용 해석 등에 의한 면밀한 검토를 제안하고 있다. 본 연구에서는 교량/열차 상호작용 해석을 수행하여 열차에서의 응답을 통해 교량 상을 주행하는 열차의 주행안전성 및 승차감을 직접적으로 평가하고자 하였다. 즉, 중앙경간 300m의 현수교를 주행하는 KTX 열차에 대하여 열차 내부의 가속도와 윤중감소율을 구해 평가하는 방법을 취하였다. 또한, 이동 열차하중과 지진하중이 동시에 작용할 경우를 고려한 교량/열차/지진 상호작용해석을 수행하여 지진 시의 응답을 평가하였다.