• 소성∙가공
• /
• 제19권7호
• /
• pp.416-422
• /
• 2010

The $\{10\bar{1}2\}$ twinning characteristics, such as active twin variants, volume fraction of twins with strain, twin morphology, twin texture and angle relationship between twins, were dependent on the activation mode (i.e., tension parallel to the caxis or compression perpendicular to the c-axis). The selection criterion of active twin variants was governed by the Schmid law. This activation of selected twin variants depending on the activation mode consequently caused a totally different plastic deformation behavior in two activation modes. The differences in the deformation characteristics, such as flow stress and work hardening rate, between both activation modes were explained in relation with activation stresses for slips and twinning, relative activities of twinning and slips during plastic deformation, grain refining effect by twin boundaries (Hall-Petch effect), and twinning-induced change in activities of slips.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.1057-1060
• /
• 2001

By comparison of the experimental results in two systems of ZnO varistors, its appear that Sb$_2$O$_3$is the indispensable element for twinning in ZnO varistors, and the Zn$_{7}$Sb$_2$O$_{12}$ spinel acts as the nucleus to form twins. A1$_2$O$_3$is not the origin of twinning in ZnO varistor, but it was found that A1$_2$O$_3$could strengthen the twinning and form a deformation twinning by ZnA$_{12}$O$_4$-dragging and pinning effect. The inhibition ratios of grain growth and nonuniformity of two systems ZnO varistors increase with the increase of A1$_2$O$_3$content. The twins affect the inhibition of grain growth, the mechanism could be explained follow as : twins increase the mobility viscosity of ZnO grain and grain boundary, and drag ZnO grain and liquid grain boundary during the sintering, then the grain growth is inhibited, and the microstructure becomes more uniform.orm.m.

• 대한소아치과학회지
• /
• 제24권4호
• /
• pp.788-794
• /
• 1997

As one of the developmental disturbance in shape of teeth, a twinning has very rare frequency in permanent teeth. Because it is possible to diagnose the twinning by use of the radiograph, it is very important to detect this anomaly early by careful examining the radiographs. The twinning produces several orthodontic problem such as crowding, protrusion, ectopic eruption of adjacent teeth. Therefore it is necessary, in proper time, the extraction and orthodontic treatment should perform.

• 열처리공학회지
• /
• 제15권1호
• /
• pp.9-15
• /
• 2002

Deformation behavior of nickel-rich Ti-51.5at.%Ni single crystals was investigated over a wide range of temperatures(77 to 440K) and strain levels(up to 9%) in compression. These alloys combined superior strength with wide range of pseudoelasticity temperature interval(~200K). The slip deformation in [001] orientation did not occur due to the prevailing slip system, and consequently, exhibited pseudoelastic deformation at temperatures ranging from 77 to 283K and 273 to 440K for the solutionized and over-aged cases, respectively. The critical transformation stress levels were in the range of 800 to 1800MPa for the solutionized case, and 200 to 1000MPa for the over-aged case depending on the temperature and specimen orientation. These stress levels are considerably higher compared to these class of alloys having lower Ni contents. The maximum transformation strains, measured from incremental straining experiments in compression, were lower compared to the phenomenological theory with Type II twinning. A compound twinning model depending on the successive austenite(B2) to intermediate phase(R) to martensite(B19') transformation predicts lower transformation strains compared to the Type II twinning case.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.114-117
• /
• 2007

In the present study, the effects of initial texture on the twinning formation of AZ31 Mg rolled sheet was investigated. Uniaxial compression tests were performed on samples cut along the normal direction and rolling direction of rolled AZ31 Mg alloy sheet at various temperatures (RT, 200, 250, 300, 350, $400^{\circ}C$) with the 0.01/s strain rate. Pole figure of rolling planes showed that basal planes of most gain were located parallel to the rolling direction. After compression test, microstructures and stress-strain curves results indicated that active deformation twining occurred only at the specimen cut along the rolling direction. The slip-twin transition with the increase of temperature was also investigated.

• 소성∙가공
• /
• 제16권6호
• /
• pp.467-472
• /
• 2007

In this study, the effects of initial texture on the twinning formation of AZ31 Mg rolled sheet was investigated. Uniaxial compression tests were carried out on samples cut along the normal direction(ND) and roiling direction(RD), respectively, of rolled AZ31 Mg alloy sheet at various temperatures (RT, 200, 250, 300, 350, $400^{\circ}C$) with the fixed strain rate($10^{-2}/s$). The results showed that deformation twining occurred actively only in the RD specimens, which promoted homogeneous deformation as compared to the ND specimens. The effect of temperature on the formation of deformation twins was also investigated, and the slip/twin transition temperature was found to be approximately $250^{\circ}C$.

• 대한금속재료학회지
• /
• 제48권4호
• /
• pp.305-314
• /
• 2010

The development of textures and microstructures during plastic deformation in a hot-extruded AZ 31 Mg alloy was investigated using a compression test with such parameters as deformation temperature, strain rate. It was observed from true stress-strain curves that twinning involves changes of the flow stresses. In the early stages of deformation at temperatures lower than $200^{\circ}C$, the occurrence of twins resulted in a decrease of the work-hardening rate, which increased drastically at a true strain of -0.05. The evolution of the deformation textures were assessed with the aid of EBSD analyses in terms of the competition between twinning and slip activity.

• Applied Microscopy
• /
• 제45권2호
• /
• pp.37-43
• /
• 2015

In present work, work-hardening behavior of TiCu-based bulk metallic glass composite with B2 particles has been studied by systemic structural and mechanical investigations. After yield, pronounced work-hardening of the alloy was clearly exhibited, which was mainly related to the martensitic transformation as well as the deformation twinning in B2 particles during deformation. At the early plastic deformation stage (work-hardening stage), the stress-induced martensitic transformation from B2 phase to B19' phase and deformation-induced twinning of B19' phase was preferentially occurred in the around interface areas between B2 phase and amorphous matrix by stress concentration. The higher hardness value was observed in vicinity of interface within the B2 particles which are probably connected with martensitic transformation and deformation twinning. This reveals that the work-hardening phenomenon of this bulk metallic glass composite is a result of the hardening of B2 particles embedded in amorphous matrix.

• 한국임상수의학회지
• /
• 제29권1호
• /
• pp.33-37
• /
• 2012

This study was performed to evaluate the rate of twin pregnancy and parturition in dairy cows. Calving records of Holstein dairy cows from 1998 to 2009 comprising Goyang and Paju cities herd with 20,990 calving events representing 820 twin births were used to evaluate twinning rate, calf sex ratio, periods of pregnancy and complication after parturition in single and twin births. Overall, the reported twinning rate was 3.9% in Holstein dairy cows. Rate of bicornual pregnancy (75%) was larger than that of unicornual pregnancy (25%) among cows having twin. Regardless of parity, the greatest twinning rate was observed in fall season from September to November. Calf sex ratios (male, M; female, F) were 48.0% FM, 28.9% MM, 21.5% FF and 0.9% mummifications for twin calves. Parturition type among cows having twins included normal (4.7%), premature (66.9%), delayed (9.2%), abortion (18.4%) and mummification (0.8%). The period of pregnancy in twin pregnancy (mean 272.6 days) was shorter than single pregnancy (mean 278.1 days). The retained placenta after parturition was over fourth times such as twin parturition (34.8%) higher than single parturition (8.5%) and the abomasal displacement was over two times such as twin parturition (10.2%) higher than single parturition (4.9%). The distribution of twin pregnancy with parities was high rate during the 2~3 parities. The prevalence of complication such as retained placenta and abomasal displacement with twin parturition revealed higher than single parturition.

• 한국재료학회지
• /
• 제27권12호
• /
• pp.643-651
• /
• 2017

Four types of high Mn TWIP(Twinning Induced Plasticity) steels were fabricated by varying the Mn and Al content, and the tensile properties were measured at various strain rates and temperatures. An examination of the tensile properties at room temperature revealed an increase in strength with increasing strain rate because mobile dislocations interacted rapidly with the dislocations in localized regions, whereas elongation and the number of serrations decreased. The strength decreased with increasing temperature, whereas the elongation increased. A martensitic transformation occurred in the 18Mn, 22Mn and 18Mn1.6Al steels tested at $-196^{\circ}C$ due to a decrease in the stacking fault energies with decreasing temperature. An examination of the tensile properties at $-196^{\circ}C$ showed that the strength of the non-Al added high Mn TWIP steels was high, whereas the elongation was low because of the martensitic transformation and brittle fracture mode. Although a martensitic transformation did not occur in the 18Mn1.9Al steel, the strength increased with decreasing temperature because many twins formed in the early stages of the tensile test and interacted rapidly with the dislocations.