• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1182-1183
• /
• 2008

In this paper, we develop PCS for doubly-fed induction-type wind generator(DFIG). PCS consists of a converter set and a controller. PCS controls the active power of wind generator and the reactive power of wind turbine system according to rotating speed, instantaneous power, grid quality, and order by transmission system operator.

• 조명전기설비학회논문지
• /
• 제29권4호
• /
• pp.102-107
• /
• 2015

In this paper, the generator control system by using PSCAD/EMTDC was modeled and several faults simulation were performed. The generator control system is composed of generator, turbine, exciter and governor. The parameters of generator control system model were obtained from field power plant. And then, the various transient phenomena through obtained several signal of developed modeling were analyzed.

• 동력기계공학회지
• /
• 제13권6호
• /
• pp.95-101
• /
• 2009

The generator for gas turbine power generation consists of the rotor which generates magnetic field, the winding coil which is the path for the field current and the wedge and retaining ring which prevents the radial movement of the coil. Relatively severe deformation was observed at the coil end section during the inspection of the generator for peaking-load operation, and the thermal-electricity and the centrifugal force were evaluated by the simple modeling of the windings to find the cause. But the simulation stress was not sufficient to induce the coil plastic deformation. The analysis result seems to be applicable to the base-load generators which runs continuously without shut down up to a year, but there had been more deformation than simulated for the generator which is started up and shut down frequently. The cause of the coil deformation was the restriction of the expansion and shrinkage. The restriction occurs when the winding coil shrinks, and the stress overwhelms the yield stress and cause the plastic deformation. The deformation is accumulated during the start-ups and shut-downs and the thermal growth occurs. The factors which induce the coil restriction during the expansion and shrinkage should be reduced to prevent the unallowable deformation. The resolutions are cutting off the field current earlier during the generator shut-down, modifying the coil end section to remove the stress concentration and making the insulation plate inserted between the coil end section and the retaining ring have the constant thickness.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제14권3호
• /
• pp.176-181
• /
• 2014

In these days, new and renewable energy is getting popular around globe and wind power generator is one of the renewable energy. In this study, we conducted a study on defect detection of composite material blade for wind power generator by applying active infrared thermography and produced a defect test piece by applying composite material used for blade of wind power generator. An infrared thermal camera and 2 kW halogen lamp are used for the purpose of research as equipments. Also, we analyzed temperature characteristic by using infrared thermal camera after checking a heat source on a test piece and found effectiveness of infrared thermography to blade of wind power generator by detecting defects resulting from temperature difference of a test piece, which eventually improve the safety and reliability of the composite material blade.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권3호
• /
• pp.192-199
• /
• 1999

During start up and shut down, the generator is rotating at a low speed and copper dusts cause arcing between the turns in the slot. Shorted turns occurred primarily by the movement of these copper dusts between individual windings in the generator rotor. Detection of shorted turns was performed in five gas turbine generators in two combined cycle power plants. Two types of permanent and temporary flux probes were used in this paper. These flux probes have been used to develop a methodology for detecting shorted turns in an operating generator's rotor. The flux probes sense the rotor winding slot leakage flux and produce a voltage proportional to the rate of change of the flux. This pattern of flux variation is the signature unique to each rotor winding. An appropriate waveform analysis technique canidentify the pole location, the slot number, and the number of shorted turns within each slot. Shorted turns in field winding of gas turbine generator(125.7 MVA) were detected to twelve turns on al total 190 turns.

• 한국유체기계학회 논문집
• /
• 제18권5호
• /
• pp.42-48
• /
• 2015

To improve the core technology of the micro gas turbine, the performance test facility was developed. This paper is focusing on the explanation of the characteristics of micro gas turbine and its assist devices. Major part of micro gas turbine were radial type of compressor, annular type of combustor, radial type of turbine, thrust foil bearing, radial foil bearing and generator. The assist devices were consist of exhaust duct, inverter, data acquisition system, load bank and test cell. Before building up the test facility, the component test was previously conducted to confirm the component performance. After the test facility was prepared, the motoring test was conducted to investigate the rotor dynamic characteristics of the micro gas turbine. Also, the part load performance test was performed. With a developed micro gas turbine test facility, the improved core technology about the micro gas turbine can be suggested to the related industries.

• 열병합발전
• /
• 통권76호
• /
• pp.11-19
• /
• 2010

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 A
• /
• pp.295-297
• /
• 2001

This paper deals with dynamic study of co-generator system with derived dynamic models of generator, excitation system, and turbine/governor from field tests. Mainly this study concentrates on frequency control of demand users that have co-generator by under-frequency relay. We simulates dynamic study of co-generator system using EMTDC.

• 한국지진공학회논문집
• /
• 제12권2호
• /
• pp.33-44
• /
• 2008

교량, 항만 및 각종 구조물과 산업설비에 대한 설계는 주로 결정론적 해석방법(Deterministic Analysis)에 의해 수행되고 있다. 그러나 구조물에 내재된 확률변수의 불확실성에 대한 영향을 보다 명확하게 평가할 뿐만 아니라 경제적인 설계를 위해서는 보다 개선된 평가방안이 요구된다. 이 연구에서는 터빈발전기 기초를 대상으로 합리적인 설계를 위해 확률유한요소법을 이용한 구조신뢰성해석을 수행하였다. 이를 위해 확률유한요소법을 신뢰성이론에 적합하도록 정식화하였으며, 대상 구조물의 부재강성 및 지진하중 등을 확률변수로 고려하여 동적응답해석 및 구조신뢰성해석을 효율적으로 수행할 수 있는 개선된 해석프로그램을 작성하였다. 작성된 해석프로그램을 이용하여 주요부재의 변위 및 부재력 응답에 대한 분산특성을 검토하였다. 아울러, 구조신뢰성해석에 따른 신뢰성지수 및 파괴확률을 제시함으로써, 대상 구조물의 구조 안전성을 정량적으로 평가하였다. 이 연구결과는 향후, 터빈발전기 기초의 개선된 설계방안을 설정함에 있어 기초자료를 제공할 것으로 기대된다.

• 한국경영과학회:학술대회논문집
• /
• 대한산업공학회/한국경영과학회 2000년도 춘계공동학술대회 논문집
• /
• pp.193-196
• /
• 2000

In the turbine-blade manufacturing industry, turbine-blades are machined and then are assembled to form a circular roll of blades. The roll of blades should be balanced as much as possible, since otherwise the efficiency of the turbine generator might degrade. We propose a heuristic method for balancing blades based on the number partitioning algorithm. The proposed method outperformed existing methods remarkably in terms of the accuracy with a negligible increase in the running time.