• 한국태양에너지학회:학술대회논문집
• /
• 2008.11a
• /
• pp.172-177
• /
• 2008

This study was carry out evaluation of long-term performance for the decentralized desalination system with the solar thermal system and the photovoltaic power system. First operating demonstration system was set up in Cheju in 2006. These system comprises the desalination unit with designed daily fresh water capacity of $2m^3$ and is supplied by a $120m^2$ evacuated tubular solar collector, a $6m^3$ heat storage tank, and a 5kW photovoltaic power generation supply the electricity for hydraulic pumps to move the working fluids. In a clear day more than 400W/$m^2$, the daily fresh water showed to produce more than about 500liter, and from January, 2007 to October, 2008 for 2 years, solar irradiance daily averaged was measured 370W/$m^2$, the daily fresh water yield showed that can be produced about 330liter.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.832-837
• /
• 2006

This study describes thermal performance of heating and cooling demonstration system using ETSC(Evacuated tubular solar collector) installed at Seo-gu art center of Kwangju. For demonstration study, a reading room with about $331m^2$ was heated and cooled using that system. The demonstration system was consisted of ETSCs, storage tank, hot water supply tank, subsidiary boiler, and subsidiary tank. From January to March in 2006, demonstration test were performed with 4 control mode to find the optimum control condition for solar thermal system. After experiments and analysis, this study found that solar thermal system of control mode IV was corresponded to 78% for the hot water supply and 49% for space heating.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.198-201
• /
• 2004

Aluminum alloys have high potential for weight reduction in automotive and other applications. But aluminum alloys have relatively low tubular hydroformability which can be enhanced by conducting the hydroforming at elevated temperatures. Hot working processes are commonly used in bulk forming such as forging and rolling, but still is rare in sheet metal forming like hydroforming. In this study hydroforming test at elevated temperatures is performed by special designed induction heating system to investigate the hydroformability of aluminum alloys. The high temperature formability characteristrics are obtained by 1?fitting forming test and circular bulging test and the effects of the process parameters such as feeding amount, internal pressure and temperatures on the tubular forming limits are mainly investigated.

• Toxicological Research
• /
• v.11 no.2
• /
• pp.169-173
• /
• 1995

The effects of tumor necrosis factor alpha $(TNF-{\alpha})$ on growth and tubular formation of bovine aortic endothelial cells were examined using an in vitro angiogenesis model system. The growth of endothelial cells was enhanced in a dose-dependent manner when the cells were cultured with $TNF-{\alpha}$ for 3 days, but $TNF-{\alpha}$, at the concentration of 1 nM or higher, produced a growth inhibition of endothelial cells when the cells were cultured for 8 days. The endothelial cells incubated with $TNF-{\alpha}$ for 48-h exhibited a typical morphologic change. Then, they showed a fibroblastoid organization of overlapping, elongated, and spindle-shaped cells. $TNF-{\alpha}$, at the concentration of O. 1 nM or higher, inhibited the tubular formation of vascular endothelial cells in an in vitro anglogenesis model using a 3-dimensional culture system.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.564-569
• /
• 2007

This study describes thermal performance of solar cooling and hot water for demonstration system with ETSC(Evacuated tubular solar collector) installed at Seo-gu art center of Kwangju. For demonstration study, a reading room with about 350㎡ was heated and cooled with the solar system. The system was consisted of ETSCs, storage tank, hot water supply tank, subsidiary boiler, subsidiary tank, absorption chiller, chiller storage tank, and cooling tower. The results of the experimental study indicated that the total solar energy gain as daily performance on a sunny day (August 25, 2007) with total daily radiation of $606\;W/m^2$ was 671 kWh, the collecting efficiency of 55%. In the case of supplies to heat source more than $83^{\circ}C$, cooling time operated by solar was driven 8.8 hours, cooling energy generated by solar system was 179 kWh and the solar cooling fraction was 79.2%, and hot water supplied with surplus heat source by the solar system was 201 kWh.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1999.04a
• /
• pp.83-85
• /
• 1999

• Restorative Dentistry and Endodontics
• /
• v.24 no.2
• /
• pp.322-329
• /
• 1999

The hydrodynamic theory of dentin sensitivity states that movement of tubular contents or tubular fluid, in either direction of dentinal tubule, causes dentin sensitivity. A corollary of that theory is that anything that can decrease dentinal fluid movement or dentin permeability should decrease dentin sensitivity. A wide variety of physicochemical methods have been used to reduce the permeability and sensitivity of exposed dentin. The purpose of this study was to evaluate the ability of 4 kinds of clinical desensitizing agents(2% NaF, 30% Potassium oxalate, MS Coat$^{(R)}$, Tubulitec system$^{(R)}$) to reduce the rate of fluid flow through dentin in vitro. Sixty coronal dentin discs, 1mm in thickness, were prepared from extracted third molars, free from decay and wear. Dentin discs were treated with 3% EDTA(Tubulicid Plus$^{(R)}$(Dental Therapeutics AB, Sweden)) to remove the smear layer and debris occluding the tubular orifices. After placing the discs in a split chamber device, the rate at which physiologic saline solution could filter across dentin under 150cm $H_2O$ hydrostatic pressure was measured. The occlusal side of the discs were then treated with MS Coat$^{(R)}$, 2% NaF, Tubulitec system$^{(R)}$, and 30% Potassium oxalate, and the filter ratio of the saline solution was measured again. The following conclusions were drawn : 1. Hydraulic conductance which was measured after the application of desensitizing agents was decreased in all the groups(p<0.05). 2. % change of hydraulic conductance was compared but no significant difference was found among the four desensitizing agents(p>0.05). 2% NaF, 30% Potassium oxalate, MS Coat$^{(R)}$ and Tubulitec system$^{(R)}$ decreased the permeability of dentin. It is considered that above four agents can be used in treating the hypersensitive teeth.

• Membrane Journal
• /
• v.23 no.2
• /
• pp.185-188
• /
• 2013

This study was carried out for microfiltration tubular membrane module equipped with self-designed air injection nozzle in order to determine the permeate flux due to the effect of membrane fouling reduction. The 0.1 wt% yeast particle solution was used as a feed solution and permeation tests were performed for the cases with and without air injection. Permeation fluxes were measured and analyzed to examine the effect of membrane fouling reduction. While the permeation flux without air injection decreased continuously, that with air injection was improved more than 30 percent than that of no air injection case.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.3B no.4
• /
• pp.179-187
• /
• 2003

In the machine tool industry, direct drive linear motor technology is of increasing interest as a means to achieve high acceleration and to increase reliability. This paper analyzes and compares the characteristics of the tubular linear actuator with the cylindrical Halbach and radial array, respectively. A tubular linear actuator with cylindrical Halbach array, consisting of parallel magnetized arc segments instead of ideal radial and axial magnetized rings, is manufactured. The magnetic field solutions due to the PMs and to the currents are established analytically in terms of vector potential, using the 2-D cylindrical coordinate system. Motor thrust, flux linkage and back emf are then derived. Thrust characteristics according to such design parameters as magnet height and air gap length are also given. The results are validated extensively by comparison with finite element analysis (FEA). Test results such as thrust measurements are also given to confirm the analysis.

• Journal of Magnetics
• /
• v.20 no.1
• /
• pp.79-85
• /
• 2015

This paper presents a comparative study of a Tubular Linear Machine (TLM) with an Axially Magnetized Single-sided Permanent Magnet (AMSPM) and an Axially Magnetized Double-sided Permanent Magnet (AMDPM) based on analytical field calculations. Using a two-dimensional (2-D) polar coordinate system and a magnetic vector potential, analytical solutions for the flux density produced by the stator windings are derived. This technique is significant for the design and control implementation of electromagnetic machines. The field solution is obtained by solving Maxwell's equations in the simplified boundary value problem consisting of the air gap and coil. These analytical solutions are then used to estimate the self and mutual inductances. Two different types of machine are used to verify the validity of these model simplifications, and the analytical results are compared to results obtained using the finite element method (FEM) and experimental measurement.