• Journal of Biomedical Engineering Research
• /
• v.21 no.4
• /
• pp.363-372
• /
• 2000

The present study investigated flow dynamics of a straight elastic blood vessel under sinusoidal flow conditions in order to understand influence of wall motion and impedance phase angle(time delay between pressure and flow waveforms) on wall shear stress distribution using computational fluid dynamics. For the straight elastic tube model considered in the our method of computation. The results showed that wall motion induced additional terms in the axial velocity profile and the pressure gradient. These additional terms due to wall motion reduced the amplitude of wall shear stress and also changed the mean wall shear stress. Te trend of the changes was very different depending on the impedance phase angle. As the wall shear stress increased. As the phase angle was reduced from 0$^{\circ}$to -90$^{\circ}$for ${\pm}$4% wall motion case, the mean wall shear stress decreased by 10.5% and the amplitude of wasll shear stress increased by 17.5%. Therefore, for hypertensive patients vulnerable state to atherosclerosis according to low and oscillatory shear stress theory.

• Horticultural Science & Technology
• /
• v.28 no.3
• /
• pp.456-461
• /
• 2010

A study was conducted to investigate the effect of topophysis, and uniting method of rootstock and scion on rooting and subsequent growth of stenting-propagated cut rose ($Rosa$ $hybrida$ Hort.) in an effort to develop an efficient stenting propagation method for domestic rose cultivars. Four cultivars used in this study were two standard type cultivars 'Sweet Yellow' and 'Hanmaum', and two spray type cultivars 'Chelsi' and 'May'. Scions were grafted on cuttings of a rootstock $Rosa$ $indica$ 'Major'. The stenting-propagated scion-rootstock unions were planted in rockwool cubes ($50{\times}50{\times}50mm$, Delta, Grodan, Denmark) and were placed in a graft-take chamber for five days before being placed on misted greenhouse beds. The rootstock was removed of all leaves and nodes. Both the base of scions and top of stocks were simultaneously cut at a $45^{\circ}$ angle for grafting. Scions were prepared as single node cuttings, each with a five-leaflet leaf. Three positions of topophysis used were 7-9th (top), 4-6th (middle), and 1st-3rd (bottom) nodes from the stem base. Four uniting materials used were tube, tube + parafilm wrap, tube + clothespin, and clothespin. Rooting and growth were affected by the topophysis and cultivar. The best topophysis for rooting was 7-9th (top) nodes in all cultivars. Topophysis affected percent rooting, and number of roots, length of the longest root, and but not weight, shoot length and graft-take. Rooting and growth were affected by the uniting method and cultivar. Tube uniting method generally showed higher percentage graft-take, percent rooting, and number of roots than other methods. However, rootstock and scion union was not complete in this treatment. On the whole, the greatest rooting and subsequent growth of stenting-propagated plants were found in the tube + clothespin method. Except 'Sweet Yellow', rooting and growth were not adequate in the clothespin method. The results suggested that a tube + clothespin method was the most effective, and this method may be used as a substitute to save labor compared to a tube + parafilm wrap method which is currently being used in commercial nurseries.

• Journal of the Korean Society of Radiology
• /
• v.5 no.5
• /
• pp.223-229
• /
• 2011

When negative electron in x-ray tube is accelerated in to a high speed and then the currency of the electron is blocked by the target, x-ray happens by the conversion of the energy. The real area where the fast accelerated electron collides to a target area is called actual focal spot. When the string focused size is observed at the central ray side, where the direction x-ray comes out, the size seems to be reduced. This focus is called effective focal spot. According to radiation angle of x-rays tube, the degree of the negative pole side presents higher value than inclination, the amount of exposed radiation that patient receives differs by the angle of positive pole, which means effective focal spot is the variable. This paper presents the correlation between size of effective focal spot and amount of exposed radiation to the patient by it, and effective research for homogenized dose dispersion by the size of effective focal spot. In conclusion, following the focal size, effective range which was -8cm ~ 0 cm on average, was found and average dose rate was 0.019 R/min. Through this range, for patients with small radiation exposure, image with good density and resolution in aspect of diagnosing will be able to be obtained.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.6
• /
• pp.513-523
• /
• 2012

The objective of this research is to examine how the lateral resisting system of selected prototypes are affected by seismic zone effect and shape irregularity on its seismic performance. The lateral resisting systems are divided into the three types, diagrid, braced tube, and outrigger system. The prototype models were assumed to be located in LA, a high-seismicity region, and in Boston, a low-seismicity region. The shape irregularity was classified with rotated angle of plane, $0^{\circ}$, $1^{\circ}$, $2^{\circ}$. This study performed two parts of analyses, Linear Response and Non-Linear Response History(NLRH) analysis. The Linear Response analysis was used to check the displacement at the top and natural period of models. NLRH analysis was conducted to invest base shear and story drift ratio of buildings. As results, the displacement of roof and natural period of three structural systems increase as the building stiffness reduces due to the changes in rotation angle of the plane. Also, the base shear is diminished by the same reason. The result of NLRH, the story drift ratio, that was subject to Maximum Considered Earthquake(MCE) satisfied 0.045, a recommended limit according to Tall Building Initiative(TBI).

• Journal of the Korea Convergence Society
• /
• v.11 no.2
• /
• pp.53-60
• /
• 2020

The purpose of this paper is to evaluate the image of the Styrofoam Wedge that can minimize the position change by supporting the wrist during the True PA and lateral examination of the wrist. In 50 people, the gap between the distal radius joint facet and the wrist bone was measured after the wrist True PA and lateral images were obtained using a general examination(vertical), tube angle(vertical:10°, lateral:20°) and Styrofoam Wedge(vertical). When joint spacing was measured in the True PA and lateral images of the wrist, general examination(5.54mm, 9.42mm), tube angle(2.05mm, 5.07mm) and Styrofoam Wedge(1.79mm, 5.46mm) were shown to be small. The smaller the joint spacing, the easier it is to observe that is open. Therefore, True PA and lateral imaging of the wrist Styrofoam Wedge can reduce the distortion of the image and thus acquire images of high diagnostic value. In addition, it may be possible to reduce the deviation caused by the change of patient's position during re-projection.

• Journal of the Korean Society of Radiology
• /
• v.7 no.4
• /
• pp.277-284
• /
• 2013

This study aims to find out geometric parameters which practitioner adjustable to reduce dose in coronary angiography. We take fluoroscopy and cine exposure by use of phantom, and got dose use the dose-area product(DAP) meter of angiography device, than convert DAP to effective dose. As results, Cine exposure shows higher dose measurement about 6-7 times than fluoroscopy. Dose in frame per second(FPS) mode could be decrease down to 70%, as lower FPS. In view of X-ray tube angle, LAO $45^{\circ}$+Caudal $30^{\circ}$ shows highest dose measurement. More use of Collimator, lower dose measurement. Source-image intensifier distance(SID) get longer to 10cm, dose of each fluoroscopy and cine exposure increase up to 25-30%. Image magnification of field of view(FOV) could increase dose up to 1.21-2 times. Also table-image intensifier distance get longer to 10cm, dose increased 1.11-1.25 times. Practitioner can adjust several geometric parameters, as FPS mode, tube angle, Collimation, SID, table-image intensifier distance, FOV. And each factors can reduce radiation dose in coronary angiography.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.3
• /
• pp.44-51
• /
• 2016

This paper presents the characteristics of the energy absorption in an expansion tube type impact absorber that is applied to a high weight drop tester and the use of a response surface methodology to predict the impact energy absorption. In order to identify the characteristics of the energy absorption, a set of finite element analysis was conducted with Abaqus Explicit. Moreover, the ISCD-II sampling method and a first order polynomial were used to build a response surface. As a result, we demonstrated that the impact energy could be controlled by four main design variables, namely an expansion pipe's thickness, inner radius, pressing die's expansion angle and expansion ratio. Additionally, we observed the relationship between the four main design variables and the impact energy absorbing time, displacement, and maximum impact force.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.3
• /
• pp.191-199
• /
• 2000

In this paper, a numerical analysis using the finite element method (FEM) is presented which models the eddy current testing (ECT) of tubes with 3-dimensional defects. For the description of 3-dimensional eddy current problems, the governing equation is derived from the Maxwell's equations. The 3-dimensional FEM formulation with hexahedral elements is carried out using the Galerkin weighted residual method. The INCONEL 600 steam generator tube with inner and outer diameter defects is adopted for the numerical analysis, and the ECT signal, which is the trajectory of the probe impedance, is calculated. For the verification of the numerical analysis method, results of numerical calculations and experiments are compared and they show good agreements. Based on this verification, several defect signals are predicted and their characteristics are investigated with the variation in the defect depth and the circumferential angle of the defect.

• Journal for History of Mathematics
• /
• v.21 no.3
• /
• pp.1-30
• /
• 2008

The success of Newton's Gravitational Theory has influenced the theory of capillarity, beginning in the early nineteenth century, by providing a major model of molecular attraction. He used the equation of the attraction of spheroids, which is expressed by second order partial differential equations, to utilize this analogy as the same kind of a particle's force, between gravitational, refractive force of light, and capillarity. The solution of the differential equation corresponds to the geometrical figure of the vessel and the contact angle which is made by the fluid. Unknown abstract functions $\varphi(f)$ represent interaction forces between molecules, giving their potential functions. By conducting several kinds of experimental conditions, it was found that the height of the ascending fluid in the tube is inversely proportional to the rayon of the tube or the distance of the plate. This model is an essential element in the theory of capillarity. Laplace has brought Newtonian mechanics to completion, which relates to the standard model of gravitational theory. Laplace-Young's equation of capillarity is applicable to minimal surfaces in mathematics, to surface tensional phenomena in physics, and to soap bubble experiments.

• Transactions of Materials Processing
• /
• v.23 no.7
• /
• pp.405-412
• /
• 2014

As a major type of heat exchanger, the steam generator (SG) produces steam from heat energy of a nuclear power plant reactor. The steam produced by the steam generator flows into a turbine, and plays an important role in electric power generation. The heat transfer tubes in the steam generator consist of approximately 10,000 U-shaped tubes, which perform a structural role and act as thermal boundaries. The heat transfer tubes conduct the thermal energy between the primary coolant (about $320^{\circ}C$, $157kgf/cm^2$) obtained from the reactor and the secondary coolant (about $260^{\circ}C$, $60kgf/cm^2$) as part of the secondary system. Recently, the heat transfer tubes in the steam generator of the pressurized water reactor (PWR) are primarily produced from Alloy 600 and Alloy 690 seamless tubes. As a pilot study to find process parameters for the cold U-bending process using rotary draw bending, numerical and experimental investigations were conducted to produce U-shaped tubes from long straight SUS304L seamless tubes. 3D finite element simulations were run using ABAQUS Explicit with consideration of the elastic recovery. The process parameters studied were the angular speed, the operation period and the bending angle. Experimental verifications were conducted to insure the suitability of the final U-shaped configurations with respect to both ovality and wall thickness.