• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.201-202
• /
• 2006

• 한국기계가공학회지
• /
• 제3권2호
• /
• pp.46-52
• /
• 2004

The most of reducers consist of many gear parts, but a ball reducer never contains a gear. As the ball reducer with gearless has no back lash, it is necessary more and more to precision machine. The reducing of ball reducer happens by cycloid curves and all instant relative velocity centers always pass on a given constant position when rotational running. Then, it is difficult to calculate cycloid curve for design and machining. So, this paper studied a software for the design of the ball reducer design and machined all parts included among cycloid curve. By using the developed software, this study has large benefit to design every ball reducer.

• 한국정밀공학회지
• /
• 제27권11호
• /
• pp.78-83
• /
• 2010

Since a tower crane is too high for a worker to ascend and by the wind in the high altitude, the possibility of a safety accident is very high, a lift assist is used. In this study, the hydraulic fall prevention device using the pressure generation device by Seok, et al. was developed. For this, the effects on the fall prevention performances of factors such as gear clearance, oil viscosity, rotative velocity and so on were evaluated by the analysis of fluid flow using FEM and the prototype was producted and a function test was performed.

• 한국기계가공학회지
• /
• 제9권6호
• /
• pp.66-70
• /
• 2010

Using two piezoelectric materials orthogonally arranged, 2-dimensional(2D) vibration in a excitation workpiece table was generated. In this study, micro milling using high frequency 2D vibration was proposed, whose locus of cutting tool is combined with original trochoid locus of milling tool and 2D elliptical locus of excitation table. From the cutting results of 2D vibrational micro milling of nickel alloy, it was observed that the machining quality and the roughness of machined surface were enhanced compared to conventional milling in a side cutting whose immersion ration is relatively low, whereas there was little betterment in a slot cutting.

• 한국생산제조학회지
• /
• 제26권3호
• /
• pp.299-305
• /
• 2017

Gate-lifting devices in small- to mid-sized sluice gates mostly employ the mechanical roller rack pinion (RRP) system. This RRP system, which consists of a rack-bar and a pinion, transforms a rotation motion into a linear one. The rack-bar has a series of roller trains that mesh with the pinion. In this study, we adopt an exact involute-trochoid tooth profile of the pinion to obtain a higher contact fatigue strength using the profile modification coefficient. Further, we determine the contact forces and investigate Hertz contact stresses to predict the pitting life of the pinion according to varying the shape design parameters. The results indicate that the design fatigue life of an RRP system for sluice gate can be achieved only when the design value of the profile modification coefficient reaches or exceeds a certain level.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.433-434
• /
• 2006

The limited slip differential(LSD) is a device which enables the driving force to be transmitted from one slipping wheel to another wheel in such case that the car is stuck in clay or snow. When the unwanted slipping occurs on one wheel, the LSD temporarily restraints the differential motion to transmit the driving force in the other wheel. So far, many types of LSD were developed such as mechanical lock type, disk clutch type, viscous coupling type, torsion type and multiple clutch type. we designed a new type of the hydraulic LSD which uses the principle of trochoid gear pump.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.453-459
• /
• 2002

In this paper. the correlation among vibration. wear and temperature are experimentally investigated when rubbing is caused by static and dynamic forces. Each measurement reflects the characteristics of the system and is useful in detecting and diagnosing the current status of rotating machinery. For experiment, the rotor system with lubricating equipment such as trochoid pump, oil tank and wear detecting sensor is implemented to simulate the rubbing condition. Experimental results show that significant change in wear quantity can be notified when vibration signal is changed by rubbing. The results can be applied to system monitoring and fault diagnosis in rotating machinery.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1142-1147
• /
• 2004

The tooth profile of helical gear that is manufactured by the rack cutter consists of the involute curve and the trochoid curve. However, gear designers are very hard to calculate the exact profile because it needs very complex information about the gear manufacturing. Therefore, the purpose of this study is to develop the automatic generation program for the helical gear using the Solid Works API. First, involute and trochoide coordinates by the rack cutter are calculated. Using the data, Visual Basic program for the helical gear model is coded. This work gives us the quick helical gear modeling and can be used as the modeling for the finite element analysis.

• Tribology and Lubricants
• /
• 제22권2호
• /
• pp.79-86
• /
• 2006

As the gerotor set with ideal profile meshes too tight, the reduction in the size of the rotor is generally adopted for a smooth operation. In this paper, a method of the profile modification for providing clearances was proposed. The meshing properties of the gerotor were analyzed and the non-boundary section of the inner rotor was identified, which denoted that the adjacent chambers were in the same pressure state. Clearances were imposed on the non-boundary section of the inner rotor, and then the profile of that section was modified as a composite curve of arcs. The other sections of the inner rotor were also interpolated as arcs. Thus, the whole profile of the inner rotor was designed as a composite curve of arcs.

• 드라이브 ㆍ 컨트롤
• /
• 제16권4호
• /
• pp.80-86
• /
• 2019

The gerotor type device is mainly used in low-speed, high-torque hydraulic motors, and is also applied as a small priming hydraulic pump. For this reason, many studies have been conducted to increase the efficiency of the gerotor pump. In this paper, we propose a new tooth profile design method different from the existing method. The new tooth design is made by modifying the tooth surface using the amplification function of the trajectories, created along the inner and outer rolling circles around the base circle. The shape of the mate rotor is then created using rotation simulation techniques. Such shapes are described as hypercloid. The designed hypercloid rotor is compared with the existing trochoid rotor, and the characteristics of the parameters and volumetric displacements are analyzed. Through this process, the optimum design with larger volumetric displacement than the existing rotor is achieved.