• 소성∙가공
• /
• 제28권3호
• /
• pp.145-153
• /
• 2019

The objective of this study is to analyze the mechanical splicing characteristic of the threaded bar according to the contact conditions of the transverse rib. In order to consider the contact conditions of the rib, selection of the main variables including the gap of the core diameter ($l_c$), rib angle (${\theta}$), and the number of contacts ($C_N$) of transverse rib was done. So as to analyze the splicing characteristic of the D51 threaded bar, a finite element (FE) simulation of the tensile test was conducted using the designed D51 threaded bar and coupler. Through FE simulation results, it was verified that the mechanical slicing characteristics varied based on the main design variables ($l_c$, ${\theta}$, and $C_N$). It was further confirmed that it was important to determine the $C_N$ in consideration of $l_c$. Additionally, the tensile test results of the D25 and D51 threaded bar combined with the couplers were similar to FE simulation results. Furthermore, to quantitatively evaluate FE simulation and test results, the calculation equation for the contacted projection area ratio (R) of the transverse rib was proposed. To secure a mechanical splicing joint of the threaded bar, it was established that the R calculated using the proposed equation had to be greater or equal to 40%.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.277-280
• /
• 2006

This paper deals with the shear deformation charateristics of concrete beams strengthened with steel/FRP Bar. Applying the shear behavioral model based on shear deformation compatibility to RC beams tested by Ahmed K. El-Sayed et al.(2006), their transverse deformation in the web are calculated at ultimated loads after decoupling the shear carried by arch action in each beams. The calculated transverse deformation at ultimated loads are nearly same for the different reinforcement ratio. From these results, the temporary transverse deformation limit criterion is deduced. Using the proposed temporary limit criterion, the shear strength of concrete beams strengthen with FRP Bar tested by Ahmed K. El-Sayed et al.(2006) is predicted. These predicted values are compared with the measured values and the results are also compared with the current ACI and JSCE equation. The proposed method predicts the ultimate shear capacities more accurately than the equation of ACI and JSCE code. The predictions by the ACI and JSCE code are founded to be very conservative.

• 콘크리트학회논문집
• /
• 제21권4호
• /
• pp.389-400
• /
• 2009

현행 기준식에 따르면 초고강도 콘크리트에서는 철근 인장이음길이보다 압축이음길이가 더 길어지는 현상 이 발생된다. 횡보강근의 영향을 반영하면 이러한 경향은 더욱 심화된다. 실제 구조물에서 반드시 존재하는 횡보강근과 철근 지름의 영향을 40, 60 MPa 콘크리트에 대한 압축이음 실험을 통해 강도와 거동 특성을 분석하였다. 지름 22, 29 mm 에 대한 실험 결과 철근 지름의 영향은 없는 것으로 나타났다. 가는 지름의 철근에서는 이음강도의 증진이 기대될 수 있으나, 압축철근에는 주로 큰 지름의 철근이 사용되므로 압축이음에서는 철근 지름의 효과를 고려할 필요가 없을 것 으로 판단된다. 횡보강근이 있는 압축이음강도는 현행 설계기준과 비교할 때 100% 이상 크므로 횡보강근을 고려한 새 로운 설계기준식의 정립이 필요하다. 지압은 이음 단부에 배근된 횡보강근에 의해서만 강도가 향상되며, 이음구간에 배 근된 횡보강근에는 무관하다. 횡보강근량이 많을수록 부착에 의해 발현되는 강도는 거의 선형적으로 증가하며, 이음단 부에만 횡보강근을 배근해도 부착강도가 6% 향상되었다. 횡보강근이 배근된 경우 부착에 의해 발현되는 강도는 인장이 음에 비해 동등하거나 더 낮아지므로, 인장이음에 비해 압축이음의 강도 증진은 단부 지압 효과로만 설명될 수 있다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.454-457
• /
• 2006

This study presents a strut-and-tie model for the development of headed bars in an exterior beam-column joint with transverse reinforcements. The tensile force of a headed bar is considered to be developed by head bearing together with bond along a bonded length as a partial embedment length. The model requires construction of struts with biaxially compressed nodal zones for head bearing and fan-shaped stress fields against neighboring nodal zones for bond stresses along the bonded length. Due to the existence of transverse reinforcements, the fan-shaped stress fields are divided into direct and indirect fan-shaped stress fields. A required development length and head size of a headed bar can be optimally designed by adjusting a proportion between a bond contribution and bearing contribution.

• 동력기계공학회지
• /
• 제4권4호
• /
• pp.70-77
• /
• 2000

On the dynamic behavior of a simple beam the influences of the velocities and distance of two moving masses have been studied by numerical method. The instant amplitude of a simple beam is calculated and analyzed for each position of the moving masses represented by the time functions. As increasing the velocties of two moving masses on the simple beam, the amplitude of the transverse vibration of the simple beam is decreased and the frequency of the transverse vibration of the simple beam is increased. As the distance between two moving masses increase, the transverse displacement of the simple beam is decrease. The simple beam is very stable in second mode at $\bar{a}=0.5$ and in third mode at $\bar{a}=0.3$.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권5호
• /
• pp.40-47
• /
• 2021

본 연구에서는 확대머리 정착이음을 갖는 연결부의 상세에 따른 구조거동을 유한요소해석을 통해 분석하였다. 복잡한 접촉조건과 비선형 거동을 나타내는 연결부의 유한요소해석을 위하여 외연적 동해석을 활용한 준정적 해석 기법을 적용하였다. 기존 실험결과와 해석결과를 비교하여 유한요소모델의 정확성을 검토하였으며, 준정적 해석 기법은 확대머리 연결부의 비선형성을 잘 반영하는 것을 확인하였다. 다양한 정착길이, 횡방향 철근지수를 갖는 21가지 유한요소모델을 활용하여 구조해석을 수행한 결과 정착길이와 횡방향 철근지수의 증가는 강도와 연성도를 증가 시키는 것을 확인하였으나, 충분한 구조성능을 확보하기 위해서는 두 가지 설계변수 모두 일정수준을 확보해야 함을 확인하였다. 최근 개정된 확대머리 정착이음 설계기준에서는 정착길이와 횡방향 철근지수를 모두 고려하는 설계식을 제시하고 있으며, 본 연구의 결과에서도 정착길이 뿐만 아니라 횡방향 보강철근이 매우 중요한 영향을 미치는 것을 확인하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.617-620
• /
• 2003

This paper presents the confinement effect of transverse reinforcement and cross-tie in hollow rectangular sectional columns. 20 analytical models with different amounts of transverse reinforcement and cross-tie in a plastic hinge region were analyzed by 3D nonlinear FEM. The analytical results show that the higher ductility can be achieved by the resonable combination of transverse re-bar and cross-tie providing sufficient lateral confinement.

• 한국도로학회논문집
• /
• 제16권4호
• /
• pp.1-9
• /
• 2014

PURPOSES: The objective of this study is to evaluate construction issues and design for transverse steel in continuously reinforced concrete pavement(CRCP). METHODS : The first continuously reinforced concrete pavement(CRCP) design procedure appeared in the 1972 edition of the "AASHTO Interim Guide for Design of Pavement Structures", which was published in 1981 with Chapter 3 "Guide for the Design of Rigid Pavement" revised. A theory that was accepted at that time for the analysis of steel stress in concrete pavement, called subgrade drag theory(SGDT), was utilized for the design of reinforcement of CRCP - tie bar design and transverse steel design - in the aforementioned AASHTO Interim Guide. However SGDT has severe limitations due to simple assumptions made in the development of the theory. As a result, any design procedures for reinforcement utilizing SGDT may have intrinsic flaws and limitations. In this paper, CRCP design procedure for transverse steel was introduced and the limitations of assumptions for SGDT were evaluated based on various field testing. RESULTS: Various field tests were conducted to evaluate whether the assumptions of SGDT are reasonable or not. Test results show that 1) temperature variations exist along the concrete slab depth, 2) very little stress in transverse steel, and 3) warping and curling in concrete slab from the field test results. As a result, it is clearly revealed out that the assumptions of SGDT are not valid, and transverse steel and tie bar designs should be based on more reasonable theories. CONCLUSIONS : Since longitudinal joint is provided at 4.1-m spacing in Korea, as long as joint saw-cut is made in accordance with specification requirements, the probability of full-depth longitudinal cracking is extremely small. Hence, for transverse steel, the design should be based on the premise that its function is to keep the longitudinal steel at the correct locations. If longitudinal steel can be placed at the correct locations within tolerance limits, transverse steel is no longer needed.

• 대한기계학회논문집A
• /
• 제21권11호
• /
• pp.1896-1911
• /
• 1997

Effects of fiber-matrix interphases on the micro-and macro-mechanical behaviors of unidirectionally fiber-reinforced composites subjected to transverse shear loading at remote distance have been studied. The interphases between fibers and matrix have been modeled by the spring-layer which accounts for continuity of tractions, but allows radial and circumferential displacement jumps across the interphase that are linearly related to the normal and tangential tractions. Numerical calculations for basic cells of the composites have been carried out using the boundary element method. For an undamaged composite the micro-level stresses at the matrix side of the interphase and effective shear stiffness have been computed as functions of fiber volume ratio $V_f$ and interphase stiffness k. Results are presented for various interphase stiffnesses from the perfect bonding to the case of total debonding. For a square array composite the results show that for a high interphase stiffness k>10, an increase of $V_f$ increases the effective transverse shear modulus G over bar of the composite. For a relatively low interphase stiffness k<1, it is shwon that an increase of $V_f$ slightly decreases the effective transverse shear modulus. For the perfect bonding case, G over bar for a hexagonal array composite is slightly larger than that for a square array composite. Also for a damaged composite partially debonded at the interphase, local stress fields and effective shear modulus are calculated and a decrease in G over bar has been observed.

• Journal of Chest Surgery
• /
• 제19권3호
• /
• pp.391-398
• /
• 1986

From Jan. 1983 to Dec. 1985, seven cases of pectus excavatum, six were male and one female, were underwent an operation at the Department of Thoracic and Cardiovascular Surgery, Kyungpook National University Hospital. The ages of patients ranged from 6 to 27 years. They all had symptoms of feeling inferiority about chest deformity. The concavity on the funnel chest varied in its extent, and the severity, which was measured by water volume filled into it, varied from 59.5cc/m2 to 129.9cc/m2. All but one patients were approached through a bilateral transverse submammary incision and one approached through a vertical midline incision. Successful surgical correction required resection of all deformed costal cartilages with transverse anterior osteotomy and internal fixation using retrosternal metal bar. No serious complication have followed the use of this technique, but minor complications such as serous accumulation, pneumothorax and strut migration have been experienced. All patients were satisfactory about the surgical results.