• 한국항만학회지
• /
• 제4권1호
• /
• pp.3-20
• /
• 1990

The Port of Pusan, the largest port in Korea, handled 23% of total sea borne cargo movement, 14% of imported cargo, 58% of exported cargo and 95% of container cargo in 1989. Also the port of Pusan has been played a key role in handing container cargo throughout the last 10 years. The paper is aimed to survey the effect of sea borne cargo movement to urban transportation, that is, to find traffic volume arising by general/bulk cargoes through the port and to estimate vehicle rated of container tractor tailer on the roads between terminal including conventional piers and ODCY, and finally the following results are obtained. (1) AADV of truck to transport general/bulk cargoes are 6,322 units in 1989,and routes penetrate into the center of city and pass through the most of urban arterials. (2) In the container transport, if HVEF is adopted to 3 of tractor trailer, AVR in each transport freeway 13.7%. (3) IF HVEF is adopted to 6 of tractor trailer. AVR are as follows: BooDoo-Ro 44.1%, WooAm-Ro 39.3%, SooYoung-Ro 17.8%, Urban freeway 20.3%. Based upon these results, the following suggestions were drawn : o ODCY scattered around the city should be unified in a few groups to raise port productivity. o Rail service for inland container transportation should be escalated to relieve urban traffic congestion. o Coastal feeder service between terminal and hinterland should be studied to restrict the penetration of container tractor trailer into the central parts in the urban areas. o Exclusive freeway system for effective container transportation should be implemented to reduce urban traffic delay.

• 한국경영과학회:학술대회논문집
• /
• 한국경영과학회 2006년도 추계학술대회
• /
• pp.284-287
• /
• 2006

We consider the transportation problem of optimizing the use of trailers and tractors. Several variants with fixed loading and unloading time are discussed. We show that the variant requiring on-time delivery can be solved in polynomial time, whereas the other variant requiring time-window delivery is NP-hard. We also discuss that if the number of loading and unloading operations assigned to each trailer or tractor is limited, even the variant requiring on-time delivery becomes NP-hard.

• Journal of Biosystems Engineering
• /
• 제30권3호
• /
• pp.147-154
• /
• 2005

The improved hitch device, which connecting the trailer to power tiller, was developed. This device, composed with spring and rubber, could reduce the vibration and shock levels during driven on off-road. The vertical vibration accelerations for the improved hitch device were measured at 6 positions, i.e. engine, hitch, seat, and three points in trailer (front, middle, and rear) for not driving but at low engine speed of 500 rpm, and compared with the existing hitch device. The results of this study could be summarized as follows; The average vibration acceleration up to 120 Hz was $0.4m/s^2$ at engine part, but it was 0.08 and $0.05m/s^2$ at trailer for existing and improved hitch device, respectively. About $38\%$ of average acceleration level could be absorbed for the improved hitch device compared with existing hitch device. The average vibration acceleration up to 40 Hz was reduced to 0.12 and $0.06m/s^2$ at trailer for existing and improved hitch device respectively, showing the reduction effect of $50\%$. The maximum acceleration occurred at up to 20 Hz of low frequency was much higher than total acceleration occurred at up to 120 Hz, which means that much loss or damage could be occurred during transporting of agricultural products on off-road. The portions of average acceleration occurred at up to 20 Hz of low frequency were $27\%\;and\;21\%$ for the existing and improved hitch device, respectively.

• Journal of Biosystems Engineering
• /
• 제33권4호
• /
• pp.224-229
• /
• 2008

This study was aimed to minimize the impact force and vibration transmitted to the transporting materials from the trailer and wheel shaft by installing the leaf spring suspension device at the space between the wheel shaft and frame of power tiller trailer. The developed trailer equipped with leaf spring suspension device was compared to the existing trailer without suspension device, in order to identify the vibration absorption effect of the leaf spring. The results of this study could be summarized as follows; (1) The length and the maximum bending amount of the leaf spring were designed as 1,000 mm and 42 mm, respectively, considering the possible space for installing at below the trailer. When 4 leaf springs were installed on both wheel shafts, the allowable maximum load was identified as 9,418 N. (2) The average vibration accelerations for the frequency less than 20 Hz, where the severe transporting loss could be represented, were $0.017\;m/s^2$ and $0.133\;m/s^2$ for the developed and the existing trailer, respectively, showing the vibration absorption effect of about 87%. And the average vibration accelerations on the driver's seat for the frequency less than 20 Hz were $0.01\;m/s^2$ and $0.20\;m/s^2$ for the developed and the existing trailer, respectively, which showed the similar vibration absorption effect. (3) The change of the average vibration accelerations for the frequency from 20 Hz to 80 Hz showed the similar tendency with the result for the frequency less than 20 Hz, but the effect for developed trailer was reduced slightly. And the effect of vibration absorption for the above 80 Hz was reduced highly. However, by installing the leaf spring suspension device at the trailer, the low frequency below 40 Hz, which could affect on transporting loss severely, could be reduced highly. (4) The maximum vibration acceleration for the frequency less than 20 Hz were $0.027\;m/s^2$ and $1.267\;m/s^2$ for the developed and the existing trailer, respectively. And the change of maximum acceleration between 20 Hz and 120 Hz was showed similar tendency with the result for the frequency less than 20 Hz, but the width of change was reduced highly.

• 한국항해항만학회지
• /
• 제34권2호
• /
• pp.137-144
• /
• 2010

In light of the growing traffic congestion problem and congestion cost, the container transport by railway has to be increased. The freight transport by railway can have decided advantages over trucks in terms of energy efficiency, emissions and cost for certain freight movements, just as transportation in the metropolitan region can have great advantages over driving truck. But the freight transport by truck should gain significant mobility benefits from a freight railway system. Thus, the DMT(Dual Mode Trailer) transport system which is coupled railway transport advantages with load transport advantages has been developed and used in the european countries. The DMT transport will therefore serve the areas required by transport organizers. The purpose of this paper is to estimate economical feasibility analysis for development of DMT transport system. Consequently, this study analyzed the characteristics of the DMT system. The horizontal load.unload system is being considered as an adoptable DMT system in consideration of the situation in Korea.

• 센서학회지
• /
• 제32권3호
• /
• pp.174-179
• /
• 2023

Bulk trailers, used for the transportation of powdered materials, such as cement and fly ash, are crucial in the construction industry. The speedy exhaustion of powdered materials stored in the tank of bulk trailers is relevant to improving transportation efficiency and reducing transportation costs. The exhaust time can be reduced by developing an automatic control system to replace the manual exhaust operation. The instantaneous or accumulated exhausts of powdered materials must be measured for automatic control of the bulk trailer exhaust system. Accordingly, we previously proposed a recurrent neural network (RNN) model that estimated the instantaneous exhaust based on low-cost pressure sensor signals without an expensive flowmeter for powders. Although our previous study utilized only an RNN model, models such as multilayer perceptron (MLP) and convolutional neural network (CNN) are also widely utilized for time-series estimation. This study compares the performance of three neural network models (MLP, CNN, and RNN) in estimating instantaneous and accumulated exhausts. In terms of the instantaneous exhaust estimation, the difference in the performance of neural network models was insignificant (that is, 8.64, 8.62, and 8.56% for the MLP, CNN, and RNN, respectively, in terms of the normalized root mean squared error). However, in the case of the accumulated exhaust, the performance was excellent in the order of CNN (1.67%), MLP (2.03%), and RNN (2.20%).

• 대한기계학회논문집A
• /
• 제34권3호
• /
• pp.353-359
• /
• 2010

최근 환경문제로 인한 차량의 연료절감이 중요해지면서 수송산업에서도 대형 수송기계의 경량설계에 대한 필요성이 지속적으로 커지고 있다. 본 연구에서는, 고강도강으로 대체된 대형 평판 트레일러 프레임의 경량모델을 개발하기 위하여 구조해석을 수행하였다. 이를 위하여, 트레일러 프레임의 주요 설계변수들을 선정하고 다구찌 기법을 적용하여 응력, 처짐량 그리고 비틀림 강성에 대하여 최적화된 결과를 도출하였다. 또한, 도출된 경량설계안의 타당성을 검토하기 위하여 시작품을 제작하여 실제 내구시험을 수행하였다.

• 한국산학기술학회논문지
• /
• 제15권3호
• /
• pp.1279-1287
• /
• 2014

한국 정부는 부산신항을 세계 2위의 환적중심 항만으로 육성하기 위한 정책 목표를 수립하고 있다. 본 논문은 이와 같은 정책 목표 달성의 한 가지 방법으로 타부두 환적의 효율적인 처리방안 제시를 목적으로 한다. 본 논문에서는 먼저 부산신항의 타부두 환적 물동량에 대한 장기 예측결과를 제시한다. 다음 부산신항의 타부두 환적을 처리할 수 있는 시스템적 대안으로 Double stack Multiple Trailer System(DMTS)와 궤도식 시스템 대안을 제시한다. 각 시스템 대안의 부산신항에 적용방법을 소개하고, 예측된 타부두 환적 물동량을 처리하기 위한 대안별 시스템 소요량 및 도입비용을 산출한다. 특히, DMTS의 경제성 분석결과 B/C = 3.7을 확보할 것으로 예상되고, 재무성 분석결과 현행 톤${\cdot}km$ 당 요금을 현행 대비 67%까지 인하할 수 있어 부산신항 타부두 환적을 효율적으로 처리할 수 있는 유력한 대안으로 판단된다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2022년도 봄 학술논문 발표대회
• /
• pp.200-201
• /
• 2022

Off-Site Construction is being widely adopted as an alternative to solve endemic problems in construction industry such as low productivity and efficiency. However, it is strongly recommended to examine the transportation process to be optimized because it determines the size of a modular and influences the cost of the construction. Therefore, in this study simulation model for optimization of modular construction transportation plan was developed using AnyLogic. As a result of the study, the influence of trailer transport capacity and transport time increases as the number of modular which should be transported from factory to site increases.

• 동력기계공학회지
• /
• 제12권6호
• /
• pp.56-63
• /
• 2008

Many advanced nations have been developing the next generation logistic systems to effectively deal with gradually increased logistic flows over the world. Particularly, dual mode trailer(DMT) systems are significantly focused as a new alternative transportation which basically provides integrating of the land and railroad services. This paper presents new driving mechanism for DMT systems using the hydraulic pressure cylinder systems. Such is mechanically composed of supporting and rotating parts independently, which are mostly important for whole system performance. We analyze feasible operational problem occurred in driving mechanism from the conventional DMT systems and compare our proposed deign specification with the Modalohr DMT system to demonstrate its reliability and practicability.