• Applied Science and Convergence Technology
• /
• v.23 no.5
• /
• pp.279-283
• /
• 2014

Al doped ZnO thin films have been deposited by a RF magnetron sputtering technique from a ZnO (2 wt.% $Al_2O_3$) target onto glass substrates heated at temperature ranging from RT to $400^{\circ}C$. X-ray diffraction analysis shows that the deposits have a preferential growth along the c-axis of a hexagonal structure. The full with at half maximum decreases from 0.45 to $0.43^{\circ}$ in the studied temperature range. The root main square surface roughness increases with substrate temperature from 1.89 to 2.67 nm. All films are transparent up to 80% in the visible wavelength range and the adsorption edge is red-shifted with substrate temperature from RT to $400^{\circ}C$. The sheet resistance increases from 92 ohm/sq to 419 ohm/sq when the deposition temperature increases from RT to $400^{\circ}C$. The increment of sheet resistance is caused by lowered carrier concentration resulting from an increase in surface roughness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.323-324
• /
• 2007

Investigation of improving the properties of UV photodetector which uses the wide bandgap of ZnO are under active progress. In this paper, transparent conducting aluminum-doped Zinc oxide films(AZO) were prepared by rf magnetron sputtering on glass(corning 1737) and p-Si substrate, were then annealed at temperature $400^{\circ}C$ for 2hr. The AZO thin films were deposited by RF sputtering system. HF power and work pressure is 120 W and 15 mTorr, respectively, and the purity of AZO target is 5N. The AZO thin films were deposited at 300, 400, $500^{\circ}C$, and $600^{\circ}C$. For sample deposited at $400^{\circ}C$, we observed best $V_r-I_{ph}$ of 0.94 mA and good transmittance.

• The Journal of Health Technology Assessment
• /
• v.6 no.2
• /
• pp.156-161
• /
• 2018

Objectives: To evaluate results and workloads of the horizon scanning of the emerging health technology since 2014 to 2016. Methods: In order to analyze the results of the emerging health technology, we identified the number of research procedure between 2014 and 2016. The sixteen findings were calculated annual workload by person, and categorized by medical phase, classification of disease, and healthcare technology. Results: An average of 5.67 personnel were involved over three years, assessment of each emerging healthcare technology was performed for each person of identifying 54 cases, filtering 2.4 cases, prioritizing 0.9 cases were performed. According to the mapping by healthcare technologies, nine medical devices (56.3%), six drugs (37.5%), and one material of the medical treatment (6.3%) were assessed. Among sixteen findings, fifteen cases were health technologies for treatment and only one case for diagnosis. Conclusion: Future plans of the horizon scanning of the emerging health technology is required appropriate manpower in charge each target number of assessment. And a legal basis should be provided for policy reflection rate. Furthermore, an evaluation criteria and procedures should be transparent to avoid a conflict of interest.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.4
• /
• pp.32-36
• /
• 2018

For various oxygen($O_2$) to argon(Ar) gas ratio, aluminum-doped zinc oxide(AZO) films were deposited for 3 min at different duty ratio by changing reverse pulse times. As the duty ratio increased, the thickness of the AZO film decreased and the sheet resistance increased. It can be concluded that When sputtering AZO Thin film, oxygen interfered with sputtering. When the reverse time was increased, the thickness of AZO was proportional to the real sputtering time and decreased. From the optical transmittance and sheet resistance, it was possible to obtain a higher figure of merits of AZO at a lower reverse pulse time. Even at the short reversed pulse time, it can be concluded that the accumulated charges on the AZO target are completely cleared. At a lower reverse pulse time, pulsed-DC sputtering of AZO is expected to be used instead of DC sputtering in the deposition of transparent conductive oxide(TCO) films without any degradation in thickness and structural/electrical characteristics.

• Geomechanics and Engineering
• /
• v.24 no.1
• /
• pp.1-14
• /
• 2021

In this study, a new approach using electrical resistivity measurement was proposed to detect grout penetration and to evaluate the grouting performance for such as waterproof efficiency in single rock fracture. For this purpose, an electrical resistivity monitoring system was designed to collect multi-channel data in real time. This was applied to a system for grout injection/penetration using a transparent fracture replica with various aperture sizes and water-cement mix ratio. The electrical resistivity was measured under various grout penetration conditions in real time, which results were directly compared to the visual observation images of grout penetration/distribution. Moreover, the grouting success status after the curing process was evaluated by measuring the electrical resistivity in relation to changes in frequency in fracture cells where grout injection and penetration were completed. Consequently, it was determined that the electrical resistivity monitoring system could be applied effectively to the detection of successful penetration of grouting into a target area and to actual field evaluation of the grouting performance and long-term stability of underground rock structures.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.2
• /
• pp.169-174
• /
• 2024

In this study, the structural, electrical, and optical properties of AZO films of various thicknesses are compared. The AZO films were deposited on a glass substrate by FTS (Facing-Target-Sputtering) This research was conducted to find the optimal thickness for Transparent Conductive Oxide (TCO). AZO has suitable properties for TCO such as low resistivity, and high transmittance. Thin films of all thicknesses showed a transmittance of over 80% in the visible light region and electrical properties improved as thickness increased. It was confirmed that the film of 300 nm thick had the best performance due to its low resistivity, and uniform surface. This research is expected to help find optimal conditions in various fields where TCO is used, such as solar cells, displays, and sensors in the future.

• Applied Chemistry for Engineering
• /
• v.16 no.6
• /
• pp.742-748
• /
• 2005

Transparent conductive indium-tin oxide (ITO) films are widely used as transparent electrodes for flat panel displays. Many of the ITO films for practical use have been prepared by magnetron sputtering, chemical vapor deposition, electron beam evaporation, etc. An oxide target composed of 10 wt% $SnO_2$ and 90 wt% $In_2O_3$ has been deposited onto polycyclic olefin polymer (POP) substrate by electron beam evaporation. POP has a higher glass transition temperature ($Tg=330^{\circ}C$) than other conventional polymers. In this study, the effects of substrate temperature and the $O_2$ introduction flow rate were investigated in terms of physical, electrical and optical properties of deposited ITO films. We investigated the effects of processing variables such as substrate temperature and the oxygen introduction flow rate. The best electrical and optical properties of deposited ITO films obtained from this study were electrical resistivity value of ${\rho}=1.78{\times}10^{-3}{\Omega}{\cdot}cm$ and optical transmittance of about 85% at 8 sccm (Standard Cubic Centimeter per Minute) $O_2$ introduction flow rate, $5{\AA}/sec$ deposition rate, $1000{\AA}$ deposited ITO thickness and $200^{\circ}C$ substrate temperature.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.49.2-49.2
• /
• 2009

투명전극은 디스플레이, 태양전지와 같은 광전자 소자에 필수적이며, 지금까지 개발된 재료 중에는 ITO가 가장 투명하면서 전기전도도가 높고 생산성도 좋기 때문에 투명전극의 재료로 사용하고 있다. ITO는 낮은 비저항(${\sim}10^{-4}{\Omega}cm$) 과 높은 투과율 (~85 %), 상대적으로 넓은 밴드갭 에너지 (3.5 eV) 의특성과 같이 뛰어난 전기적 광학적 특성에 반해서 높은 원자재 가격, 불안정한 공급량 등으로 인한 문제점이꾸준히 제기되고 있다. 따라서 $In_2O_3$:Sn, ZnO:Al, ZnO:Ga, ZnO:F, ZnO:B, TiN 등과 같은 물질들로대체하려는 연구가 활발하게 진행되고 있다. ZnO는 ITO보다원자재의 수급이 원활하기 때문에 원가가 낮으며, 상대적으로 낮은 온도에서도 제작이 가능하다. 또한 화학적으로 안정적이므로 ZnO에 Al, Ga 등의 3족 원소를 도핑함으로써 낮은 비저항의 박막 제작이 가능하고, ITO 박막과 비교하여 etching이 쉬우며 기판과의 접착성이 좋으며, sputtering 공정시 plasma 분위기에서의 안정성이 뛰어나고 박막증착율이 높기 때문에 투명전극으로 적합한 재료이다. 본 연구에서는 cylindrical type의 Aldoping된 ZnO single target을 사용하여 박막 증착 압력의 변화를 주어 유리기판 위에 DC sputtering을 하였다. Fieldemission scanning electron microscope (FESEM)을 통해 ZnO:Al 박막의 표면의 형상과 두께를 확인하였으며, X-ray diffraction (XRD) 분석을 통해 박막의 결정학적 특성을 관찰하였다. 투명전극용 물질로서 ZnO:Al 박막의 적합성 여부를 확인하기 위하여 Van der Pauw 방법을 이용하여 박막의 비저항, 전자 이동도, 캐리어 농도를 측정하였으며, 박막의 기계적 성질 및 표면 접착성을 확인하기 위하여 nano-indentaion 분석을 하였다. 또한 UV-vis spectrophotometer를 이용하여 ZnO:Al 박막의 투과율을 분석하여 투명전극으로의 응용 가능성을 확인하였다.

• Journal of the Korean Ceramic Society
• /
• v.41 no.6
• /
• pp.476-480
• /
• 2004

AZO (Al-doped ZnO) thin films were deposited on glass by pulsed magnetron sputtering method, and their structural, electrical and optical properties were investigated. XRD patterns showed that a highly c-axis preferred AZO film was grown in perpendicular to the substrate when pulse frequency of 30 ㎑ was applied to the target. Microstructure of thin films showed that the fibrous grain of tight dome shape was grown. The deposition rate decreased linearly with increase of pulse frequency, and the lowest resistivity was 8.67${\times}$10$\^$-4/ $\Omega$-cm for the film prepared at pulse frequency of 30 ㎑. The optical transmittance spectra of the films showed a very high transmittance of 85∼90%, within visible wavelength region and exhibited the absorption edge of about 350 nm. The characteristics of the low electrical resistivity and high optical transmittance of AXO films suggested a possibility for the application to transparent conducting oxides.

• Tribology and Lubricants
• /
• v.36 no.1
• /
• pp.1-10
• /
• 2020

Large-area two-dimensional (2D) materials synthesized by chemical vapor deposition on donor substrates are promising functional materials for conductors, semiconductors, and insulators in flexible and transparent devices. In most cases, 2D materials should be transferred from a donor substrate to a target substrate; however, 2D materials are prone to damage during the transfer process. The damages to 2D materials during transfer are caused by contamination, tearing, and chemical doping. For the commercialization of 2D materials, a damage-free, large-area, and productive transfer process is needed. However, a transfer process that meets all three requirements has yet to be developed. In this paper, we review the recent progress in the development of transfer processes for 2D materials, and discuss the principles, advantages, and limitations of each process. The future prospects of transfer processes are also discussed. To simplify the discussion, the transfer processes are classified into four categories: wet transfer, dry transfer, mechanical transfer, and electro-chemical transfer. Finally, the "roll-to-roll" and "roll-to-plate" dry transfer process is proposed as the most promising method for the commercialization of 2D materials. Moreover, for successful dry transfer of 2D materials, it is necessary to clearly understand the adhesion properties, viscoelastic behaviors, and mechanical deformation of the transfer film used as a medium in the transfer process.