• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.306-309
• /
• 1989

This paper describes the Manufacturing process and electrical properties of ac thick film electroluminescent lamps which made of the mixture of ZnS:Cu,Cl phosphor powder and polymer binding materials. The phosphor layer is sandwiched between two electrodes, one of which is transparent, and is supported by a substrate. The substrate may be glass or flexible plastic or it may be metallic. In this study we manufactured suspend layer which consists of ZnS:Cu,Cl powder suspended in a NBR. As yet our results are behind other commercial product in electrical properties and brightness. However they can be improved by selection of appropriate polymer binding materials, development of blending technology.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.3
• /
• pp.180-184
• /
• 2015

Stainless steel (SS) mesh was used to fabricate photoelectrode for flexible dye-seisitzed solar cells (DSSCs) in order to evaluate them as replacements for more expensive transparent conductive oxide(TCO). We fabricated the DSSCs with new type of photoelectrode, which consisted of flexible SS mesh coated with 100 nm thickness titanium (Ti) protective layer deposited using electron-beam deposition system. SS mesh DSSCs with protective layer showed higher efficiency than those without a protective layer. The best cell property in the present study showed the open circuit voltage (Voc) of 0.608 V, short-circuit current density (Jsc) of $5.73mA\;cm^{-2}$, fill factor (FF) of 65.13%, and efficiency (${\eta}$) of 2.44%. Compared with SS mesh based on DSSCs (1.66%), solar conversion of SS mesh based on DSSCs with protective layer improved about 47%.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.1
• /
• pp.39-44
• /
• 1999

The dielectric layers in AC plasma display panel(PDP) are essential to the discharge cell structure, because they protect metal electrodes from sputtering by positive ion bombarding in discharge plasma and form a sheath of wall charges which are essential to memory function of AC PDP. This layer should have high dielectric breakdown voltage, and also be transparent because the luminance of PDP is strongly correlated this layer. In this paper, we discussed the dielectric breakdown voltage and transparency of the dielectric layer under various conditions. As a result, on the $15\mum$ thickness, the minimum dielectric breakdown voltage was 435V and the transmission coefficient was about 80% after $570^{\circ}C$ firing process. It can be proposed that the resonable dielectric thickness in AC PDP is $15\mum$ because it has about 75V margin on the maximum applied voltage.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.287-287
• /
• 2010

We report a new direct patterning method, called liquid bridge-mediated nanotransfer molding (LB-nTM), for the formation of two- or three-dimensional structures with feature sizes between tens of nanometers and tens of micron over large areas. LB-nTM is based on the direct transfer of various materials from a mold to a substrate via a liquid bridge between them. This procedure can be adopted for automated direct printing machines that generate patterns of functional materials with a wide range of feature sizes on diverse substrates. Arrays of TIPS-PEN TFTs were fabricated on 4" polyethersulfone (PES) substrates by LB-nTM using PDMS molds. An inverted staggered structure was employed in the TFT device fabrication. A 150 nm-thick indium-tin oxide (ITO) gate electrode and a 200 nm-thick SiO2dielectric layer were formed on a PES substrate by sputter deposition. An array of TIPS-PEN patterns (thickness: 60 nm) as active channel layers was fabricated on the substrate by LB-nTM. The nominal channel length of the TIPS-PEN TFT was 10 mm, while the channel width was 135 mm. Finally, the source and drain electrodes of 200 nm-thick Ag were defined on the substrate by LB-nTM. The TIPS-PEN TFTs can endure strenuous bending and are also transparent in the visible range, and therefore potentially useful for flexible and invisible electronics.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.56-56
• /
• 2018

Transparent conductive oxides (TCOs) have attracted attention due to their high electrical conductivity and optical transparency in the visible region. Consequently, TCOs have been widely used as electrode materials in various electronic devices such as flat panel displays and solar cells. Previous studies on TCOs focused on their electrical and optical performances; there have been numerous attempts to improve these properties, such as chemical doping and crystallinity enhancement. Recently, due to rapidly increasing demand for flexible electronics, the academic interest in the mechanical stability of materials has come to the fore as a major issue. In particular, long-term stability under bending is a crucial requirement for flexible electrodes; however, research on this feature is still in the nascent stage. Hydrogen-incorporated amorphous In-Sn-O (a-ITO) thin films were fabricated by introducing hydrogen gas during deposition. The hydrogen concentration in the film was determined by secondary ion mass spectrometry and was found to vary from $4.7{\times}10^{20}$ to $8.1{\times}10^{20}cm^{-3}$ with increasing $H_2$ flow rate. The mechanical stability of the a-ITO thin films dramatically improved because of hydrogen incorporation, without any observable degradation in their electrical or optical properties. With increasing hydrogen concentration, the compressive residual stress gradually decreased and the subgap absorption at around 3.1 eV was suppressed. Considering that the residual stress and subgap absorption mainly originated from defects, hydrogen may be a promising candidate for defect passivation in flexible electronics.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.85-87
• /
• 2000

In this study, high-density plasma etching characteristics of ITO(indium tin oxide) films used for transparent electrodes in display devices have been investigated. The etch characteristics of ITO as a function of $Ar/CH_4$ gas mixtures were analyzed using QMS(quadrupole mass spectrometry), OES(optical emission spectroscopy), and ESP(electrostatic probe). ITO etch rates were increased with the addition of moderate amount of $CH_4$ to Ar due to the increased chemical reaction between $CH_3$ or H and ITO in addition to the physical sputtering of ITO by Ar ion bombardment. However, the addition of excess amount of $CH_4$ decreased the ITO etch rates possibly due to the increased polymer formation on the ITO surface. Also, the measurement data obtained by QMS and OES suggested that $CH_3$ radicals are more activity involved in the etching of ITO compared to H radicals.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.192-192
• /
• 2013

본 연구에서는 RF/DC 마그네트론 스퍼터링 시스템을 이용하여co-sputtering 방법으로 성장시킨 고이동도를 갖는Ge-doped $In_2O_3$In2O3 (IGO) 박막의 전기적, 광학적, 구조적 특성을 평가하고, 이를 유기태양전지와 유기발광다이오드에 적용함으로써 고이동도 IGO 투명전극의 소자 적용가능성을 타진하였다. GeO2 타겟에 인가되는 도핑 Power와 급속열처리 온도가 30 W, $500^{\circ}C$일 때, 최적화 된 IGO 박막으로부터 $2.8{\times}10^{-4}$ Ohm-cm의 낮은 비저항과 86.9% (550 nm)의 높은 투과도를 확보하였다. 뿐만 아니라 Near Infra-red (750~1,200 nm) 영역에서의 IGO투명전극의 광투과율이 결정질의 ITO보다 높은(약15%) 투과도를 보이는 것을 통해 IGO박막의 높은 LAS (Lewis Acid Strength) 값을 가지는 Ge 원소의 도핑이 NIR 영역의 광투과율 향상에 미치는 영향을 확인할 수 있었다. 최적 조건의 IGO 박막을 적용하여 Fill Factor 67.38%, Short circuit current density 8.43 mA/cm2, open circuit voltage 0.60 V, efficiency 3.44%의 유기태양전지 및 19.24%의 외부양자효율을 갖는 유기발광다이오드를 제작함으로써 결정질 ITO 전극(20.05%)을 대체할 수 있는 고투과, 고이동도 IGO 투명 전극 및 이를 이용한 광전소자 적용 가능성을 타진하였다.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.4
• /
• pp.13-18
• /
• 2019

Superconducting junctions of topological insulator (TI) are expected to host Majorana bound state, which is essential for developing topological quantum information devices. In this study, we fabricated Josephson junctions (JJs) made of Sb-doped Bi2Se3 TI nanoribbon and PbIn superconducting electrodes. In the normal state, the axial magnetoresistance data exhibit periodic oscillations, so-called Aharonov-Bohm oscillations, due to a metallic surface state of TI nanoribbon. At low temperature of 1.5 K, the TI JJ reveals the superconducting proximity effects, such as the critical current and multiple Andreev reflections. Under the application of microwave, integer Shapiro steps are observed with satisfying the ac Josephson relation. Our observations indicate that highly-transparent superconducting contacts are formed at the interface between TI nanoribbon and conventional superconductor, which would be useful to explore Majorana bound state in TI.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.1
• /
• pp.47-51
• /
• 2008

The Al:Au double-layer metal electrode for use in transparent, dual emission of organic light-emitting diode (OLED) was fabricated. The electrode of Al:Au metals with various thicknesses was deposited by the vacuum thermal evaporation technique. For Al thickness of 1 nm, a bottom luminance of $4880\;cd/m^2$ was observed at 8 V. Otherwise, top luminance of $2020\;cd/m^2$ were observed at 8 V. In addition, the threshold voltages of the electrodes were 2.2 V. It was forward that the inserting 1 nm Al between LiF and Au enhanced electron injection with tunneling effect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.379-379
• /
• 2007

The characteristics of indium-zinc-tin-oxide (IZTO)-Ag-IZTO multilayer grown on a PET substrate were investigated for flexible organic light-emitting diodes. The IZTO-Ag-IZTO (IAI) multilayer anode exhibited a remarkably reduced sheet resistance of 4 ohm/sq and a high transmittance of 84%, despite the very thin thickness of the IZTO (30 nm) layer. In addition, it was shown that electrical and optical properties of IAI anodes are critically dependent on the thickness of the Ag layer, due to the transition of Ag atoms from distinct islands to continuous films at a critical thickness (14 nm). Moreover, the IAI/PET sample showed more stable mechanical properties than an amorphous ITO/PET sample during the bending test due to the existence of a ductile Ag layer. The current density voltage-luminance characteristics of flexible OLEDs fabricated on an IAI/PET substrate was better than those of flexible OLEDs fabricated on an ITO/PET substrate. This indicates that IAI multilayer anodes are promising flexible and transparent electrodes for flexible OLEDs.