• 한국소음진동공학회논문집
• /
• 제22권11호
• /
• pp.1106-1112
• /
• 2012

This paper deal with a technique for monitoring machining conditions by measuring the vibration of cutting forces at milling machining. The vibrations of cutting forces in milling process were measured and analyzed to be related with processing parameters. The magnitude of cutting force is linearly proportional to the feed rate and cutting depth, and frequency of cutting force is linearly proportional to the rotating speed. Wired and wireless communication methods were applied in transmitting the measured vibration signals and the two methods were compared. The magnitude of the vibration signals transmitted by the wireless communication method was similar to that transmitted by the wired communication method.

• 한국소음진동공학회논문집
• /
• 제16권6호
• /
• pp.602-608
• /
• 2006

In order to evaluate performance of anti-vibration gloves, it is necessary to measure the transmitted vibration to the hand and the applied forces at the same time while gripping the vibrating handle. In the study a system was developed to measure both the vibration and the forces. The system consists of a measurement handle with eight strain gauges and two accelerometers and a PC-based system with a software for signal processing and evaluation of the hand-transmitted vibration and for control of applied forces in the pre-determined range. The handle was installed on the vibration shaker which is strong enough so as not to be affected by dynamic coupling with the hand-arm system. Whole procedure of ISO 10819 to determine the vibration transmissibility of anti-vibration gloves was programmed into the system. As an example of the application, three subjects joined the test to get vibration transmissibilities of anti-vibration gloves where each glove was tested twice a subject. Average and standard deviation of vibration transmissibility were also calculated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.792-796
• /
• 2013

A practical process to optimize engine mounts on construction equipment is presented in this research. Transmitted force from the engine is estimated by using stiffness of the mount rubber which varies with frequency, amplitude and pre-load, and by the engine excitation force that comes from piston mass and gas pressure and so on. The transmitted force is measured through TPA(Transfer Path Analysis) and is then compared with the estimated force. The optimum mount position and stiffness are solved using MATLAB. The result shows the improvement on engine mount vibration.

• International Journal of Automotive Technology
• /
• 제8권4호
• /
• pp.521-531
• /
• 2007

Measurement of the vibration transmitted through rotating shafts such as half shafts in vehicles is of interest in applications such as noise transfer analysis and the study of operating deflections. Vibration signals transmitted through a rotating shaft usually include six degree-of-freedom components, thus making the measurement of vibration a challenging task. In the present work, a new measurement method is presented, one that resolves the minimum of only two one-axis accelerometer signals into all components of vibration with reasonable accuracy. The method utilizes the Dopplerized signals obtained from accelerometers attached to a rotating shaft and a Void-Kalman order tracking filter to decompose signals into orders of different vibration components. The new method proposed in the present work is verified by simulated run-up test data and applied to an experimentally obtained data set.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.109-119
• /
• 1995

A driveline incorporating universal joints when driving through an angle can excite various components in a vehicle with second order excitation of torsional and bending vibrations, being transmitted either audibly(noise), or physically(vibration). For a certain range of vehicle dpeed noises can be radiated from the cab wall, in which resonances occur by the excitations transmitted from the driveline as a vibration source. In this paper, the excitation mechanism of cab noises is studied especially for the vehicle speed range of 65 .approx. 75 km/h through the simulation for torsional vibrations of the driveline and for bending vibrations of the cab of an 11 Ton grade Cargo Truck, and verified additionally by vibration and noise measurements. As a result, it is found that the uncomfortable noises in the cab are caused mainly by the abrupt increase of the joint angle of driveline near the axle differential resulted from the excessive clearance alignment of the leaf spring gate.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.127-132
• /
• 2001

In this paper, transmitted sound reduction performance of smart panels is studied according to different piezoelectric materials with piezoelectric shunt damping. Peizo-damping is implemented by using a newly proposed tuning method. This method is based on electrical impedance model and maximizing the dissipated energy at the shunt circuit. By measuring the electrical impedance at the piezoelectric patch bonded on a structure, an equivalent electrical model is constructed near the system resonance frequency. After shunting elements are connected to the equivalent circuit, the shunt parameters are optimally searched based on the criterion of maximizing the dissipated energy at the shunt circuit. Transmitted sound reduction performance is compared according to different piezoelectric materials with peizo-damping. Two piezoelectric materials are selected: PZT-5 and QuickPack IDE actuator. When resonant shunt circuit is considered, the use of PZT-5 exhibited the good sound reduction performance.

• Wind and Structures
• /
• 제29권1호
• /
• pp.33-41
• /
• 2019

The interaction of head waves with an infinite row of identical, equally spaced, rectangular breakwaters is investigated in the presence of uneven bottom topography. Using linear water wave theory and matched eigenfunction expansion method, the boundary value problem is transformed into a system of linear algebraic equations which are numerically solved to know the velocity potentials completely. Utilizing this method, reflected and transmitted wave energy are computed for different physical parameters along with the wave field in the vicinity of breakwaters. It is observed that the wave field becomes more complicated when the incoming wavelength becomes smaller than the channel width. A critical ratio of the gap width to the channel width, corresponding to the inflection point of the transmitted energy variation, is identified for which 1/3 of the total energy is transmitted. Similarly, depending on the incident wavelength, there is a critical breakwater width for which a minimum energy is transmitted. Further, the accuracy of the computed results is verified by using the derived energy relation.

• 한국소음진동공학회논문집
• /
• 제15권8호
• /
• pp.988-995
• /
• 2005

Vibration has been severly increased at the branch pipe of main steam header since the commercial operation of nuclear power plant. Intense broad band disturbance flow at the discontinuous region such as elbow, valve, and header generates the acoustical pulsation which is propagated through the piping system. The pulsation becomes the source of low frequency vibration at piping system. If it coincide with natural frequency of the pipe system, excessive vibration is made. High level vibration due to the pressure pulsation related to high dynamic stress, and ultimately, to failure probability affects fatally the reliability and confidence of plant piping system. This paper discusses vibration effect for the branch pipe system due to acoustical pulsations by broad band disturbance flow at the large main steam header in 700 MW nuclear power plant. The exciting sources and response of the piping system are investigated by using on-site measurements and analytical approaches. It is identified that excessive vibration is caused by acoustical pulsations of 1.3 Hz, 4.4 Hz and 6.6 Hz transmitted from main steam balance header, which are coincided with fundamental natural frequencies of the piping structure. The energy absorbing restraints with additional stiffness and damping factor were installed to reduce excessive vibration.

• 소음진동
• /
• 제8권3호
• /
• pp.504-512
• /
• 1998

For analyzing the torsional vibration of a multiple stepped gear system containing a pair of triple gears, a transfer matrix model based on Hibner's branch method is developed and the natural properties of the branched rotor system are calculated with using the $\lambda$-matrix formulation. A Campbell diagram, in which the excitation sources caused by the mass unbalances of the rotors and the transmitted errors of thegearings are considered, shows that, at the neighborhood of the operating speed, there are the four critical speeds amplifying the first mode and the fifth mode. For the surpression of the gear box vibration, two ways are suggested by referring the mode shapes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1265-1267
• /
• 2006

현재 ISO 에서는 공구제조업체에서 해당 공구의 수전달 진동을 측정하여 제시하도록 하는 규격을 제정 중에 있으며, 이를 위해서는 공구에서 발생하는 진동과 영향을 평가하는 기술이 확보되어야 하며, 이 과정에서 측정 불확도 수준을 결정하는 것이 매우 중요하다고 하겠다. 본 연구에서는 동력 공구 작업시 작업자의 손으로 전달되는 진동을 측정하고 그 영향을 평가함에 있어서 발생할 수 있는 불확도를 분석하였다. 먼저, ISO 5349 규격을 적용함에 있어서 존재하는 불확도 인자들을 분류하고, 각 인자들이 어느 정도 수준의 불확도를 발생시키는지 시험을 통해서 확인하고 분석하였다.