• Journal of Advanced Navigation Technology
• /
• v.15 no.3
• /
• pp.386-391
• /
• 2011

CRU (contiguous resource unit) composed of adjacent OFDMA subcarriers is popularly adopted for recently developed cellular communication standards, e.g. IEEE 802.16e/m. If multiple CRUs having different SNR are assigned to a mobile station, and multiple packet streams are independently transmitted by using H-ARQ transmission, an achievable data rate can be varied according to the channel allocation method of re-transmission packets and new transmission packets. In this paper, the optimum channel allocation method for the above stated problem, and several sub-optimum channel allocation methods to reduce the computational complexity of the optimum allocation method are proposed. According to the simulation results, a sub-optimum allocation method assigning a CRU having good SNR to new transmission packet shows marginal performance loss compared with optimum method, however, the computational complexity can be significantly reduced.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.2B
• /
• pp.44-52
• /
• 2005

This paper proposes a neural network prediction model to improve the valid packet transmission rate for the QoS(Quality of Service) of multimedia transmission. The Round Trip Time(RTT) and Packet Loss Rate(PLR) are predicted using a neural network and then the transmission rate is decided based on the predicted RTT and the PLR. The suggested method will improve the transmission rate since it uses the rate control factors corresponding to time of data is being transmitted, while the conventional one uses the transmission rate determined based on the past informations. An experimental set-up has been established using a Linux PC system, and the multimedia data are transmitted using UDP protocol in real time. The valid transmitted packets are about 5% higher than the one in the conventional TCP-Friendly congestion control method when the suggested algorithm was applied.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.4
• /
• pp.77-83
• /
• 2016

Recently, interests for maintenance of transmission tower are increasing to extend life of structures and reduce maintenance cost. However, existing classical diagnosis method of corrosion deteriorated degree on the transmission tower steel members, visual inspection, has a problem that error often due to difference of inspector's individual knowledge and experience. In order to solve the problem, this study carried out to develop the corrosion deterioration inspection tool for transmission tower steel members. This tool is composed of camera equipment and computer-aided diagnosis system. We standardized the photographing method by camera equipment to obtain suitable pictures for image processing. Diagnosis system was designed to evaluate automatically degree of corrosion deterioration for member of transmission tower on the basis of the RGB color image processing techniques. It is anticipated that developed the corrosion deterioration inspection tool will be very helpful in decision of optimal maintenance time for transmission tower corrosion.

• International Journal of Computer Science & Network Security
• /
• v.22 no.7
• /
• pp.91-102
• /
• 2022

With the evolution of wireless sensor network (WSN) technology, the routing policy has foremost importance in the Internet of Things (IoT). A systematic routing policy is one of the primary mechanics to make certain the precise and robust transmission of wireless sensor networks in an energy-efficient manner. In an IoT environment, WSN is utilized for controlling services concerning data like, data gathering, sensing and transmission. With the advantages of IoT potentialities, the traditional routing in a WSN are augmented with decision-making in an energy efficient manner to concur finer optimization. In this paper, we study how to combine IoT-based deep learning classifier with routing called, Kriging Regressive Deep Belief Neural Learning (KR-DBNL) to propose an efficient data packet routing to cope with scalability issues and therefore ensure robust data packet transmission. The KR-DBNL method includes four layers, namely input layer, two hidden layers and one output layer for performing data transmission between source and destination sensor node. Initially, the KR-DBNL method acquires the patient data from different location. Followed by which, the input layer transmits sensor nodes to first hidden layer where analysis of energy consumption, bandwidth consumption and light intensity are made using kriging regression function to perform classification. According to classified results, sensor nodes are classified into higher performance and lower performance sensor nodes. The higher performance sensor nodes are then transmitted to second hidden layer. Here high performance sensor nodes neighbouring sensor with higher signal strength and frequency are selected and sent to the output layer where the actual data packet transmission is performed. Experimental evaluation is carried out on factors such as energy consumption, packet delivery ratio, packet loss rate and end-to-end delay with respect to number of patient data packets and sensor nodes.

• Wind and Structures
• /
• v.34 no.2
• /
• pp.215-230
• /
• 2022

Majority of transmission line system failures at many locations worldwide have been caused by severe localized wind events in the form of tornadoes and downbursts. This study evaluates the structural response of two different transmission line systems under equivalent F2 tornadoes obtained from real incidents. Two multi-span self-supported transmission line systems are considered in the study. Nonlinear three-dimensional finite element models are developed for both systems. The finite element models simulate six spans and five towers. Computational Fluid Dynamics (CFD) simulations are used to develop the tornado wind fields. Using a proper scaling method for geometry and velocity, full-scale tornado flow fields for the Stockton, KS, 2005 and Goshen County WY, 2009 are developed and considered together with a previously developed tornado wind field. The tornado wind profiles are obtained in terms of tangential, radial, and axial velocities. The simulated tornadoes are then normalized to the maximum velocity value for F2 tornadoes in order to compare the effect of different tornadoes having an equal magnitude. The tornado wind fields are incorporated into a three-dimensional finite element model. By varying the location of the tornado relative to the transmission line systems, base shears of the tower of interest and peak internal forces in the tower members are evaluated. Sensitivity analysis is conducted to assess the variation of the structural behaviour of the studied transmission lines associated with the location of the tornado relative to the tower of interest. The tornado-induced forces in both lines due to the three different normalized tornadoes are compared with corresponding values evaluated using the simplified load case method recently incorporated in the ASCE-74 (2020) guidelines, which was previously developed based on the research conducted at Western University.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.89-96
• /
• 1995

The application of the 4-pole parameter method with 1 - D theory is acceptable for intake system analysis. However, the limitaion appears during the analysis of complicated intake system since this method is developed based on the plane wave thoery. For the intake system analysis, the usage of BEM(Boundary Element Method) is introduced describing its disadvantage. To combine benefits of both method. a hybrid method is introduced. This hybrid method consists of the 4-pole parameter with I-D theory and BEM. The developed method is applied to an automobile intake system analysis to obtain the transmission loss.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.2
• /
• pp.87-94
• /
• 2004

In this paper, the experimental design of an intake system was studied using the two microphones method and the taguchi method. The transmission loss was utilized to represent the performance of noise reduction for the intake system which was estimated by measuring sound power at inlet and outlet with two microphones, respectively. Two microphones method used in this paper was followed by wave decomposition theory. The robust designing parameters of an intake system were extracted by adapting a cost function with the taguchi method, which optimized the process. Finally the effectiveness of the propose method was validated with the experimental data.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.114-119
• /
• 2003

In this paper, the experimental design of an intake system was studied using the two microphones method and the taguchi method. The transmission loss was utilized to represent the performance of noise reduction for the intake system which was estimated by measuring sound power at inlet and outlet with two microphones, respectively. Two microphones method used in this paper was followed by wave decomposition theory The robust designing parameters of an intake system were extracted by adapting a cost function with the taguchi method, which optimized the process. Finally the effectiveness of the propose method was validated with the experimental data.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.11C
• /
• pp.1068-1075
• /
• 2005

In this paper we propose a video coding method and associated packetization and decoding methods for error resilient transmission over the Internet. The proposed method re-organizes the input image into several mutually similar subimages. For this case, if the one of the subimage is lost in the network, the lost one is recovered by the proposed error concealment method which uses the correctly received other subimages. The performance of the proposed method is confirmed by the empirical results. The proposed method is not limited to the Internet communications but is applicable to the other packet-based networks.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.23 no.4
• /
• pp.333-340
• /
• 2013

Objectives: This study was designed to establish an accurate analytical method for asbestos in a biological sample for determining occupational asbestos-related diseases and relief of the health effects of environmental asbestos. Methods: Biological samples were obtained from lungs of rats following intratracheal instillation of asbestos(Chrysotile, anthophyllite) and were prepared according to digestion method(Wet digestion, high temperature ashing, low temperature ashing). The samples were then analyzed for asbestos fibers using a transmission electron microscope equipped with an energy dispersive X-ray spectrometer. Results: Low temperature plasma ashing removed more of the organic components and reduced fiber loss compared to the wet digestion method, making specimens so prepared more suitable for transmission electron microsocpy. Conclusions: The low temperature ashing technique is the most accurate method for analyzing asbestos in biological samples.