• 한국통신학회논문지
• /
• 제15권10호
• /
• pp.829-841
• /
• 1990

본 논문에서는 우리 나라 디지털 다중화 계위 5차군 전송속도 564.993Mb/s를 실제의 광전송 데이터 속도라 가정하고, 국내 565Mb/s 광전송시스템을 유지 보수할 뿐만 아니라 디지털 광전송용 통신망을 B.S.I.화하기 위하여, 단국중계장치에서 기존의 전송로부호들 중 최적의 전송로부호라 사료되는 mBIZ 전송로부호를 이용한 새로운 전송로 프레임 구조를 제안한다. 제안한 프레임 구조대로 565Mb/s 광전송용 단국중계장치에서 순수정보신호계열의 속도를 변환한 후 pulse stuffing 하는 방식으로 시스템 하드웨어를 실현시킨 결과, 전송 에러에 의한 연속적인 시스템 에러 파급 현상 즉, 도미노 현상을 방지할 수 있었으며, timing jitter와 동부호연속수도 억압할 수 있었다. 또한 광단국장치에서의 total BER을 10정도까지 향상시킬 수 있기 때문에 시스템 SNR을 2dB 정도 개선할 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전력기술부문
• /
• pp.35-38
• /
• 2005

This paper suggests the method that forecast Dynamic Line Rating (DLR). Thermal Overload Risk (TOR) of next time is forecasted based on current weather condition and DLR value by Monte Carlo Simulation (MCS). To model weather element of transmission line for MCS, we will propose the use of weather forecast system and statistical models that time series law is applied. Also, through case study, forecasted TOR probability confirmed can utilize by standard that decide DLR of next time. In short, proposed method may be used usefully to keep safety of transmission line and reliability of supply of electric Power by forecasting transmission capacity of next time.

• 전기학회논문지
• /
• 제58권12호
• /
• pp.2462-2467
• /
• 2009

This paper proposes a dual band branch line coupler (BLC) using a composite right/left handed (CRLH) transmission line. The existing dual band BLCs with open stubs require hundreds of line impedance for the open stub as the frequency bands approach to each other, so it has been almost impossible to realize them. However in the proposed BLC, a CRLH transmission line replaces the open stub with an extremely high line impedance so that the BLC circuit may be realized even two frequencies are close to each other. As an example, a dual band BLC operating at 1800MHz and 2300MHz (the frequency ratio is 1:1.28) is designed and measured. Open stubs with $560\Omega$ line impedance are replaced by CRLH transmission lines for realizing the dual band BLC. The measured performances prove that the dual band operation is well acceptable and the proposed design method is successful even the ratio between two frequencies is not around two nor more.

• 조명전기설비학회논문지
• /
• 제26권2호
• /
• pp.78-85
• /
• 2012

Low-Voltage power lines should equip surge protection devices which protect electronic equipments and human lives against lightning and abnormal voltages. Data transmission capacity of the power line is determined by frequency characteristics of the surge protective devices. To analyze the effects of surge protective devices on the data transmission performance, various combinations of installation methods are tested which include ZnO varistor elements that is compatible with class I, class II and class III. The result claims that ZnO varistor for class III is found to be one of the main factors that deteriorates the transmission performance. To overcome this problem a serial connection methed between Gap type SPD and ZnO varistor is proposed. With the proposed scheme, laboratory experimental results show that the data transmission performance can be improved up to 91.9[%] with proper SPD combination.

• Journal of Magnetics
• /
• 제11권2호
• /
• pp.90-94
• /
• 2006

A finite-element method is used to analyze loss generation and electromagnetic noise absorption characteristics of a coplanar waveguide transmission line integrated with a magnetic thin film. Parameters used in the analysis are the electrical resistivity of the magnetic layer and the thickness of both magnetic and insulating layers. The results indicate that L-C resonance is the main loss mechanism of the electromagnetic noise absorption.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권5호
• /
• pp.1051-1057
• /
• 2001

In this paper, we deal with three types of modelling method for the analysis of galloping in power transmission line (PTL). The single mass model is obtained under linearization method and it is applied into f-order model. On these models, the nature frequencies of PTL are obtained and it makes an effects on the galloping directly. In simulation, we verify that the maximum magnitude of nature frequency depends on the galloping distance of PTL. Also from the analysis of frequency response, a few of reduction method for galloping are introduced which is effected by distance of PTL, wind velocity and icing types.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 A
• /
• pp.145-147
• /
• 2002

In this paper, the improved fault locating method using distributed parameter which calculating the reduced voltage and current according to the ground capacitance in long transmission line was proposed. For the purpose of the fault locating algorithm non influenced source impedance, the loop method was used in the system modeling analysis. To enhance the fault locating, zero sequence of the fault current which is variable according to ground capacitance was not used but positive and negative sequence. System model was simulated using EMTP software. To verify the accuracy of proposed method, in different cases 64 sampled data per cycle was used and 160km and 300km long transmission line has fault resistance $0{\Omega}\;and\;100{\Omega}$ respectively was compared.

• 조명전기설비학회논문지
• /
• 제26권2호
• /
• pp.51-60
• /
• 2012

An improved method for detecting fault distance in overhead transmission lines is described in this paper. Based on single-ended measurement, propagation theory of traveling waves together with the wavelet transform technique is used. In estimating fault location, a simple, but fundamental method using the time difference between the two consecutive peaks of transient signals is considered; however, a new method to enhance measurement sensitivity and its accuracy is sought. The algorithm is developed based on the lattice diagram for traveling waves. Representing both the ground mode and alpha mode of traveling waves, in a lattice diagram, several relationships to enhance recognition rate or estimation accuracy for fault location can be found. For various cases with fault types, fault locations, and fault inception angles, fault resistances are examined using the proposed algorithm on a typical transmission line configuration. As a result, it is shown that the proposed system can be used effectively to detect fault distance.

• 한국산학기술학회논문지
• /
• 제11권7호
• /
• pp.2541-2548
• /
• 2010

본 논문에서는 결함접지구조와 포토닉 밴드갭과 같은 주기구조가 삽입된 전송선로의 특성 임피던스 계산에 대하여 기술한다. ${\lambda}$/4 전송선로 이론을 이용한 계산하는 종래 방법을 고찰하고, 이 방법에 의한 계산 결과가 주파수 의존성이 커서 신뢰도가 낮다는 문제점을 제시한다. 균일한 유전체 기판에 구현된 전송선로의 특성 임피던스 계산에 적용되는 해석적인 방법을 주기구조가 결합된 전송선로에서도 적용될 수 있음을 보인다. ${\lambda}$/4 전송선로 방법과 대신 해석적 방법으로 특성 임피던스를 구하고, 후자의 결과가 주파수에 관계없이 비교적 고정된 값을 가짐을 제시한다. 또한 종래에 특성 임피던스 계산 사례가 없었던 PBG 구조를 지닌 전송선로에 대해서도 특성 임피던스를 계산한다. 시뮬레이션뿐만 아니라 직접 제작하여 측정한 S-파라미터로부터 각각 특성 임피던스를 계산하고 서로 비교하여 상당히 유사함을 보인다. 그리고 이를 통하여 해석적 방법에 의한 특성 임피던스의 결정 방법이 DGS와 PBG와 같은 주기구조가 결합된 전송선로의 특성 임피던스 계산에 잘 적용될 수 있음을 보인다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 A
• /
• pp.497-499
• /
• 2004

Due to a typhoon named MAEMI on Sep12, 2004, 7 transmission towers collapsed and 3 were damaged in the Gyeongnam and Busan areas. These caused long-term black-outs in Goeje-do. When a transmission tower collapses or is damaged, Construction will take more than 2 months and this will be accompanied by long-term black-outs. Therefore a temporary iron pole is used in such emergencies. Current temporary rehabilitation angle steel iron Pole consistes of around 800 members, 2,800 bolts and it takes about 5 days to construct a temporary transmission line. Consiquently wide black-outs occur during the construction of the temporary transmission line. To reduce black-out time, the construction period must be reduced as much as possible. This paper presents new methods to reduce temporary transmission line construction time to within 48 hours by applying a self-reliance assembling method instead of the current man power assembling method and by modulizing each angle steel with duralumin.