• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.2
• /
• pp.137-150
• /
• 1997

The problem of electromagnetic coupling into a thin conducting wire through a slot in an infinite conducting is analyzed by use of MPIE(mixed potential integral equation) and two- dimensional moment method using subsectional(rooftop) basis functions. The equivalent circuit is derived using a center-repesentation method which is valid in a narrow slot case. The equi- valent magnetic currents on the slot and the induced currents on the wire are caculated respec- tively, for the TM wave is incident upon the slot with arbitrary angle of incidence. The theoretical transmission coefficients of transmission line which is composed of thin-wire and infinite conducting plate with a narrow slot are compared and found to be in good agreement with experimental results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.5
• /
• pp.1061-1071
• /
• 2015

In the present study, the Navier-Stokes (N-S) equations delineating water flows inside porous media were derived applying Reynolds transport theorem in order to provide a basis for analyzing water wave problems inside the porous media. Then, the derived N-S equations were compared with the same species of equations in existing researches. Based on the N-S equations, a set of Boussinesq equations was then derived in such a form that the dispersiveness and nonlinearity of water waves inside the porous media can be properly reproduced. Finally, numerical analyses were carried out to demonstrate the validity of the equations. The reflection and transmission coefficients of porous breakwaters were calculated and compared with the results of existing hydraulic experiments. The numerical results showed a rather sensitive dependency on the virtual mass coefficient of grains constituting the porous media. The selection of the coefficient with zero turned out to give nice agreements with numerical and experimental results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.995-998
• /
• 2003

TiO$_2$ thin films have been grown by MOCVD. Envelope methods are applied to the analysis of the transmission spectra to obtain the optical constants such as refractive indices and extinction coefficients for the TiO$_2$ thin films. The envelope methods are proved to be accurate by simulating the transmission spectra. TiO$_2$ thin films start to crystallize at 35$0^{\circ}C$ and then crystallize fully into anatase phase at foot or higher temperatures. Activation energies are obtained by plotting the deposition rate with varying the substrate temperature. It is 17.8 kcal/mol for the reaction limited regions. The refractive infer and the extinction coefficient of the TiO$_2$ thin film at λ=632.8 nm increases from 2.19 to 2.32 and decreases from 0.021 to 0.007, respectively, as the substrate temperature increases from 400 to $600^{\circ}C$.

• Journal of Navigation and Port Research
• /
• v.33 no.9
• /
• pp.645-651
• /
• 2009

In this study, a series of laboratory experiments were carried out to investigate the weak reflection of regular and random water waves over a train of protruded permeable shore structures. A cylindrical slit type breakwater and the alternatives are employed and compared for reflecting and transmitting capabilities of incident waves including wave forces. A series of random waves were generated by using the Bretschneider-Mitsuyasu frequency and directional spectrum. Measured spectrum of irregular waves without breakwaters is verified by comparing with those of the input waves generated. Weak reflection is occurred at the breakwater center of the peak frequency. If the row of breakwaters is fixed at three layers and the relative height of breakwater is fixed at 0.6, around 45% of incident wave energy is reflected to offshore. It is also found that the transmission of directional random waves increases as the maximum frequency parameter increases. A very good agreement is observed. Reflection coefficients of permeable submerged breakwaters are less than those of impermeable breakwaters. The upside-down L shape is recommended for a small fishery harbor mooring in terms of reflecting capability and of practical application. The final design was applied to the wharf of a small beach of Seolly, near Namhae at the southeast coast of Korea.

• Journal of Korea Foresty Energy
• /
• v.7 no.1
• /
• pp.28-36
• /
• 1987

To know the possibility of fuel substitution for Diesel engine with the seed oil of Evodia daniellii, which is one of the native oil seed trees in Korea. the refined seed oil mixed with light oil in the various rates was tested in the 8 PS Diesel engine: the output, the fuel consumption rate, the governor performance, the rpm stability in the total loading condition. the content of graphite in the burned gas, and the traction coefficients at the different gear stages were maintained The following results were discussed. 1. The output at the normal revolution (2200rpm)was increased as the percent seed oil increased. At the lower rpm (2000-1500rpm )there were no consistent difference in the outputs among fuels of the different percent seed oil 2. The rate of fuel consumption was inclosed as the percent seed oil increased in each loading condition. 3. The more percent sud oil was mixed in the fuel. the better governor performance appeared at both the instantaneous and stable speed. 4. The more percent seed oil was mixed In the fuel, the more stable rpm ratio was maintained 5. The graphite content In the burned gas was increased as the load increased, but there was no apparent difference in the content at each load among the 100$\%$ seed oil, the 100$\%$ light oil, and the mixtures in various rates. 6. In all fuel mixtures the maximam traction coefficent appeared at the third transmission gear stage. Generally in over all transmission gear stages the fuel mixtures of the seed oil:light oil ratio from 7:3 to 5:5 resulted greater traction force than the other fuels.

• Progress in Medical Physics
• /
• v.13 no.3
• /
• pp.139-148
• /
• 2002

The measured attenuation correction with transmission (Tx) scans produced quantitatively accurate images. However, it was not clear for optimal emission (Ex) and Tx scan time in PET imaging. This study was to evaluate acceptable Ex and Tx scan time by simulating clinical situations using various phantoms. Cylindrical and NEMA phantom were used for $^{18}$ F-PET scan using 2D protocol in GE Advance PETTM scanner. Cylindrical phantom was filled with 136 MBq 18F, and five regions of interests (ROI) were drawn on 23 slices. NEMA phantom had three inserts containing water, air and polytetrafluoro-ethylene (PTFE). Outside of these inserts were filled with 309 MBq of $^{18}$ F, and total 12 ROIs were drawn on 23 slices. Scans were carried out according to five Ex scan times: 2, 5, 10, 15, and 30 min, and nine Tx scan times: 2, 3, 4, 5, 7, 10, 15, 20, and 30 min. Images were reconstructed using measured attenuation correction, and ROI analyses were performed for all images, and mean, standard deviation (SD), coefficient of variation and percent errors were calculated. For cylindrical phantom study, ROI mean and SD were decreased as Ex and Tx time increased. Coefficients of variation were kept constant, when Tx was greater than 10 min. The amount of error decreased for the increment of Ex time from 10 min to 15 min was almost the same to that from 15 min to 30 min. In NEMA phantom Tx 15 min showed the lowest er개r level when the percent errors for three inserts were summed for all of the Ex times. This study suggested that Ex 15 min and Tx 15 min were acceptable as optimal scan time for the scanning protocol and the dose of radiopharmaceuticals used in these phantom study.

• Journal of the Korean Magnetics Society
• /
• v.13 no.5
• /
• pp.216-220
• /
• 2003

In this work, transmission characteristics of read and write signal were calculated when a MRAM (magnetic random access memory) cell is operated up to 10 GHz. Test device having long read and write lines was modeled in 3 dimensions to perform a simulation. The simulation was divided into two parts, read and write operations, and S-parameters were computed utilizing FEM (finite element method) algorithm. Transmission coefficients, S$\sub$21/, for read and write operations of MRAM device which was designed for a single cell test configuration were analyzed from DC to 1 GHz and DC to 10 GHz, respectively. When the insulator thickness between the bit and sense lines was increased from 500 to 1500 ${\AA}$, 3 dB attenuation frequency was increased by 3.3 times, from 135 to 430 MHz. The length of the bit and sense lines were 600 ${\mu}$m. In addition, access time was estimated by calculating the propagation delay utilizing S-parameters.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.1
• /
• pp.19-33
• /
• 2002

A numerical method to efficiently secure necessary design informations of the hydraulic characteristics of rubble mound breakwater was attempted here. The method combines the exterior wave field with the interior wave field which is formulated incorporating porous media flow inside the breakwaters. An approximate method based on the long wave assumption was used for the exterior wave field while a boundary element method was used for the interior wave field. A hydraulic experiment was also performed to verify the validity of the numerical analysis. The numerical results were compared with experimental data and results from existing formulae. They generally agreed in both reflection and transmission coefficients. The calculated pore pressures also showed a similar pattern with experimental data, even if they gave some significant differences in their values fur some cases. The main cause of such differences can be attributed to the strongly nonlinear wave field occurring on the frontal slope of the breakwater. The direct input of dynamic pressures(measured from hydraulic experiment) into the numerical method was suggested as a promising method to enhance the predictability of pore pressures.

• Computers and Concrete
• /
• v.33 no.5
• /
• pp.621-630
• /
• 2024

This study presents novel electromagnetic wave-based methods for evaluating the integrity of cement-based structures using time domain reflectometry (TDR). Two cement-based plates with embedded rebars are prepared under sound and defective conditions. TDR tests are carried out using transmission lines with various numbers of artificial joints, and electromagnetic waves are measured to assess the integrity of the plates. The experimental results show that the travel time of electromagnetic waves is consistently longer in sound plates than in defective ones, and an increase in the reflection coefficients is observed in the defect zone of the defective plates. Electromagnetic wave velocities are higher in the defective plates, especially when connectors are present in the transmission line. A novel approach based on the area of the reflection coefficient provides larger areas in the defective plates, and the attenuation effect of the electromagnetic waves induces a difference in the areas of the reflection coefficient between the two defect conditions. An alternative method using the centroid of the defect zone slightly overestimates the location of the defect zone. The length of the defect zone is estimated using the defect ratio and wave velocities of cement, air, and plate. The length of the defect zone can also be calculated using the travel times within the plate, total measured length of the plate, and wave velocities in the cement and air. Therefore, the electromagnetic wave-based methods proposed in this study may be useful for estimating the location and length of defect zones by considering attenuation effects.

• Nuclear Engineering and Technology
• /
• v.56 no.9
• /
• pp.3501-3511
• /
• 2024

Titanium alloys play a vital role in optimizing the effectiveness and security of nuclear reactors, strengthening structural durability, and facilitating the effective handling of nuclear waste. The aim of this study is to investigate the gamma-ray, neutron, and transmission properties of four common titanium alloys through the examination of the deposited energy amount in the liquid sodium coolant material, in relation to the mechanical properties of these alloys. MCNP (version 6.3) is utilized for designing the titanium pipes. Next, the pipes were re-designed considering the elemental mass fractions and densities of the investigated titanium alloys. Grade 26 sample is reported with the highest values of mass attenuation coefficients and the lowest HVL values among those investigated alloys. Grade 26 is reported to have the lowest TF value, whereas Grade 12 demonstrated the highest TF value. The highest Effective Removal Cross Section (Σ_R, 1/cm) value against fast neutrons is reported for Grade 26. The utilization of Grade 26 sample as pipe material resulted in the lowest deposited energy amount (MeV/g) and subsequent lowest contamination in the coolant material. Out of the alloys that were chosen for analysis, it has been determined that Grade 26 exhibits the highest level of strength. It can be concluded that the Grade 26 alloy exhibits desirable characteristics for applications in nuclear technologies that require superior gamma-ray and neutron absorption properties, as well as exceptional mechanical properties. Nevertheless, it is essential to emphasize the importance for ongoing studies to enhance the existing material properties of Grade 26, with the aim of achieving improved safety and efficacy in nuclear applications.