• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1313-1314
• /
• 2007

This paper presents organic thin-film transistors (OTFTs) with poly(3-hexylthiophene)(P3HT) semiconductor and several polymeric dielectric materials of poly(vinyl phenol)(PVP), poly(vinyl alcohol)(PVA), and polyimide(PI) by using soluble process. The fabricated OTFT's have inverted staggered structure using transmission line method(TLM) pattern. In order to evaluate the electrical characteristics of the OTFT, capacitance-voltage(C-V) and current-voltage(I-V) were measured. C-V graphs were measured at several frequencies of 100 Hz, 1 kHz, and 1 MHz and ID-VDS graphs according to $V_{GS}$. The current on/off ratio and threshold voltage with each of PVP, PVA, and PI based OTFTs were measured to $10^3$, and -0.36, -0.41, and -0.62 V. Also, the calculated mobility with each of PVP, PVA, and PI was 0.097, 0.095, and 0.028 $cm^{2}V^{-1}s^{-1}$, respectively. In the cases of PVP and PVA, the hole mobility of P3HT was in excellent agreement with the published value of 0.1 $cm^{2}V^{-1}s^{-1}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.15-23
• /
• 2002

In this study, metal/ZnO contacts were thermally annealed at different temperatures (as-dep., 400$^{\circ}C$, 600$^{\circ}C$, 800$^{\circ}C$, 1000$^{\circ}C$) for the investigation of electrical properties, and surface and interface characteristics. The analysis of the element composition and the chemical bonding state of the surface was made by the XPS(X-ray photoelectron spectroscopy). An attempt was made to establish the electrical property-microstructure relationship for the (Ti, Au)/ZnO. The Ti/ZnO contact exhibits an ohmic characteristics with a relatively high contact resistance of 4.74${\times}$10$\^$-1/ $\Omega$$\textrm{cm}^2$ after an annealing at 400$^{\circ}C$. The contact showed a schottky characteristics when the samples were annealed at higher temperature than 400$^{\circ}C$. The transition from the ohmic to schottky characteristics was contributed from the formation of the oxide layers as was confirmed by the peaks for O-O and Ti-O bondings in XPS analysis. For the Au/ZnO contact the lowest contact resistance was obtained from the as-deposited sample. The resistance was slowly increased with annealing temperature up to 600$^{\circ}C$. The ohmic characteristics were maintained eden fort 600$^{\circ}C$ annealing. The XPS analysis showed that the Au-O intensity was dramatically decreased with temperature above 600$^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.228.2-228.2
• /
• 2013

본 논문은 InN와 GaN를 교대로 증착하는 교번성장법(Alternate Growth Method)을 이용해 형성한 높은 인듐(Indium) 조성을 갖는 InGaN (HI-InGaN) 구조의 열처리(Rapid Thermal Annealing, RTA) 온도 및 시간에 대한 구조와 광학적 특성을 Double Crystal X-ray Diffraction (DCXRD), Transmission Electron Microscopy와 Photoluminescence (PL) 장비를 사용하여 분석한 결과를 보고한다. DCXRD 스펙트럼에서 HI-InGaN 박막은 GaN(0002)로부터 $2.98^{\circ}$ 분리된 위치에서 회절 신호를 관찰 할 수 있다. 그리고 GaN와 HI-InGaN 신호 사이의 넓은 범위에서 미약하지만 신호가 관찰 되는데, 이는 InN와 GaN 계면에서 발생하는 상호확산 확률의 차이에 기인한 In 조성이 다른 InGaN 신호로 해석할 수 있다. 열처리 온도를 $775^{\circ}C$로 고정하고 시간을 10, 20, 30초로 각각 변화시켜 RTA를 진행한 DCXRD 스펙트럼에서 GaN(0002)로부터 $0.7{\sim}1.1^{\circ}$ 떨어진 위치에서 InGaN 피크를 확인 할 수 있다. RTA 시간이 증가 할수록 HI-InGaN 신호의 위치가 GaN 피크 방향으로 이동하며, 세기가 증가하는 것을 확인 할 수 있다. HI-InGaN의 PL 스펙트럼에서 상온 발광파장은 1369 nm 이며, 반치폭(Line-width)은 51.02 nm을 보였다. RTA 수행 후 발광파장에 따른 광세기가 각각 달라졌으며, 특히 900 nm 부근의 신호가 상대적으로 크게 증가하는 것을 확인할 수 있었다. RTA에 따른 HI-InGaN의 구조 및 광학적 특성 변화를 InN와 GaN 계면에서 In, Ga 원자의 상호확산 효과현상으로 논의할 예정이다.

• Korean Journal of Metals and Materials
• /
• v.56 no.12
• /
• pp.910-914
• /
• 2018

Since catalyst technology is one of the promising technologies to improve the working performance of next generation energy and electronic devices, many efforts have been made to develop various catalysts with high efficiency at a low cost. However, there are remaining challenges to be resolved in order to use the suggested catalytic materials, such as platinum (Pt), gold (Au), and palladium (Pd), due to their poor cost-effectiveness for device applications. In this study, to overcome these challenges, we suggest a useful method to increase the surface area of a noble metal catalyst material, resulting in a reduction of the total amount of catalyst usage. By employing block copolymer (BCP) self-assembly and nano-transfer printing (n-TP) processes, we successfully fabricated sub-20 nm Pt line and cross-bar patterns. Furthermore, we obtained a highly ordered Pt cross-bar pattern on a Ni thin film and a Pt-embedded Ni thin film, which can be used as hetero hybrid alloy catalyst structure. For a detailed analysis of the hybrid catalytic material, we used scanning electron microscope (SEM), transmission electron microscope (TEM) and energy-dispersive X-ray spectroscopy (EDS), which revealed a well-defined nanoporous Pt nanostructure on the Ni thin film. Based on these results, we expect that the successful hybridization of various catalytic nanostructures can be extended to other material systems and devices in the near future.

• Journal of Sensor Science and Technology
• /
• v.31 no.2
• /
• pp.90-95
• /
• 2022

The effect of the structure of an ITO nanoparticle film sensor on its performance was studied. A printed ITO film (P-ITO film) was fabricated on a flexible polyethylene terephthalate (PET) substrate, and the contact resistance of the electrode and sensor response change were clarified according to the detection position. The contact resistance between Ag and P-ITO was observed to be -204.4 Ω using the transmission line method (TLM), confirming that a very good ohmic contact is possible. In addition, we confirmed that the contact position of the analyte had a significant influence on the response of the sensor. Based on these results, the performance of the four types of sensors was compared. Consequently, we observed that 1) optimizing the resistance of the printed film, 2) optimizing the electrode structure and analyte input position, and 3) optimizing the electrode area are very important for fabricating a metal oxide nanoparticle (MONP) sensor with optimal performance.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.601-609
• /
• 2023

In this paper, we propose an artificial intelligence-based high-speed fault diagnosis method using an FPGA in the event of a ground fault in a DC system. When applying artificial intelligence algorithms to fault diagnosis, a substantial amount of computation and real-time data processing are required. By employing an FPGA with AI-based high-speed fault diagnosis, the DC breaker can operate more rapidly, thereby reducing the breaking capacity of the DC breaker. therefore, in this paper, an intelligent high-speed diagnosis algorithm was implemented by collecting fault data through fault simulation of a DC system using Matlab/Simulink. Subsequently, the proposed intelligent high-speed fault diagnosis algorithm was applied to the FPGA, and performance verification was conducted.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.7 no.2
• /
• pp.78-86
• /
• 2004

Recently GPS and mobile GIS technologies based on LBS(location based service) have played an important role as DSS(decision supporting system) for domestic forest fire extinguishment policies. In this study forest fire extinguishments information management system based on mobile GIS technique was designed to seize the exact location on wireless network so that it helps to guide the safe and efficient extinguishments affairs and provide the extinguishments environment toward ground fighting teams and the central forest government in real time. Moreover, possibly to operate this system, the foundation technologies by the name of '.gci' such as the spatial data compression method, the spatial data transmission method over wireless network and the spatial analysis interface on PDA should be mainly considered. Especially, in this study the spatial data compression method having high compression rate from 51% to 62% for each polygon, line, and point data, without the loss of data was developed.

• Journal of Broadcast Engineering
• /
• v.14 no.5
• /
• pp.573-588
• /
• 2009

In this paper, we propose a novel video quality degradation monitoring scheme titled VR-VQMS(Visual Rhythm based Video Quality Monitoring Scheme) over an IPTV service prone to packet losses during network transmission. Proposed scheme quantifies the amount of quality degradation due to packet losses, and can be classified into a RR(reduced-reference) based quality measurement scheme exploiting visual rhythm data of H.264-encoded video frames at a media server and reconstructed ones at an Set-top Box as feature information. Two scenarios, On-line and Off-line VR-VQMS, are proposed as the practical solutions. We define the NPSNR(Networked Peak-to-peak Signal-to-Noise Ratio) modified by the well-known PSNR as a new objective quality metric, and several additional objective and subjective metrics based on it to obtain the statistics on timing, duration, occurrence, and amount of quality degradation. Simulation results show that the proposed method closely approximates the results from 2D video frames and gives good estimation of subjective quality(i.e.,MOS(mean opinion score)) performed by 10 test observers. We expect that the proposed scheme can play a role as a practical solution to monitor the video quality experienced by individual customers in a commercial IPTV service, and be implemented as a small and light agent program running on a resource-limited set-top box.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.6
• /
• pp.645-654
• /
• 2021

In this paper, we proposed a protocol to convert 2W telephone analog signals to Ethernet data in a private PSTN 2W tactical voice system. There are several kinds of operational problems in the tactical telephone network where 2W telephone copper lines are installed hundreds of meters away from the PBX in a headquarter site. The reason is that it is difficult to install and maintain the 2W telephone copper cable in severe operational fields and to meet safety and stability operational requirements of the telephone line under lighting and electromagnetic environments. In order to solve these challenging demands, we proposed an efficient method that the 2W analog interface signals between a private PBX system and a 2W telephone is converted to Ethernet messages using the optical Ethernet data communication network already deployed in the tactical weapon system. Thus, it is not necessary to install an additional optic cable for the ethernet telephone line and to maintain the private PSTN 2W telephone network. Also it provides safe and secure telecommunication operation under lightning and electromagnetic environments. This paper presents the conversion protocol from 2W telephone signals over Ethernet interface between PBX systems and 2W telephones, the mutual exchange protocol of ethernet messages between two converters, and the rule to process analog signal interface. Finally, we demonstrate that the proposed technique can provide a feasible solution in the tactical weapon system by analyzing its performance and experimental results such as the bandwidth of 2W telephone ethernet network and the transmission latency of voice signal, and the stability of optic ethernet voice network along with the ethernet data network.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.6
• /
• pp.2739-2746
• /
• 2011

This paper proposes the method for more effectively calculating X/R which is the ratio of equivalent reactance(X) and resistance(R) of the bulk power system and analyses the characteristic of X/R values by applying the proposed method to the real bulk power systems. X/R is used to determine the rating of the relay in the bulk power systems and its value has been accepted to be big enough to ignore the equivalent resistance of the bulk power systems. However, X/R is calculated as a big number when only the upper transformer and transmission line are considered. The correct approach to calculating X/R needs to consider all the parameters including generators, transformers, lines and loads. This paper calculates X/R of the bulk power systems using dynamic models which have been used to analyse the power system stability. The effectiveness of the proposed method is verified by applying it to the test system and X/R values of the real bulk power systems are analyzed. In addition, the dependence of X/R on the closeness of its calculating locations to the generator is verified by using the marginal loss factor which has been used in the electricity market.