• Journal of the Korean Vacuum Society
• /
• v.17 no.1
• /
• pp.40-45
• /
• 2008

We present the effect of Ga-doping on the electrical, structural and optical properties of ZnO layers with a thickness of ${\sim}500nm$ deposited on glass substrates. Polycrystalline ZnO and Ga-doped ZnO (GZO) layers were deposited by radio frequency (rf) magnetron sputtering at room temperature. Based on the X-ray diffraction (XRD) and transmission electron microscopy (TEM) data, the crystalline quality of Ga-doped ZnO film was improved and GZO film has a preferred orientation along with the (002) crystal direction. The transmittance of the GZO film was enhanced by 10% in the visible region from that of the ZnO film. From photoluminescence (PL) data, the ratio of intensity of near band edge (NBE) emission to deep level (DL) emission was as high as 2.65:1 and 1.27:1 in the GZO and ZnO films, respectively. The res istivities of GZO and ZnO films were measured to be 1.27 and 1.61 $\Omega{\cdot}cm$, respectively. The carrier concentrations of ZnO and GZO film were approximately 1018 and 1020 $cm^2$/Vs, respectively. Based on our experimental results, the Ga-doping improves the electrical, structural and optical properties of ZnO film with potential application.

• Membrane Journal
• /
• v.21 no.3
• /
• pp.222-228
• /
• 2011

Poly(vinyl chloride)-g-poly(oxyethylene methacrylate) (PVC-g-POEM) graft copolymer was synthesized via atom transfer radical polymerization (ATRP) and used as an electrolyte for electrochromic device. Plasticized polymer electrolytes were prepared by the introduction of propylene carbonate (PC)/ethylene carbonate (EC) mixture as a plasticizer. The effect of salt was systematically investigated using lithium tetrafluoroborate ($LiBF_4$), lithium perchlorate ($LiClO_4$), lithium iodide (LiI) and lithium bistrifluoromethanesulfonimide (LiTFSI). Wide angle X-ray scattering (WAXS) and differential scanning calorimetry (DSC) measurements showed that the structure and glass transition temperature ($T_g$) of polymer electrolytes were changed due to the coordinative interactions between the ether oxygens of POEM and the lithium salts, as supported by FT-IR spectroscopy. Transmission electron microscopy (TEM) showed that the microphase-separated structure of PVC-g-POEM was not greatly disrupted by the introduction of PC/EC and lithium salt. The plasticized polymer electrolyte was applied to the electrochromic device employing poly(3-hexylthiophene) (P3HT) conducting polymer.

• Korean Journal of Materials Research
• /
• v.10 no.7
• /
• pp.493-498
• /
• 2000

The effects of RRA treatment on the microstructures and mechanical properties of 7050 Al alloy were investigated by differential scanning calolimetry, transmission electron microscopy, microhardness measurement and electrical conductivity. The hardness of 2nd-step aged specimen at $175^{\circ}C$ was decreased to mimimum value and increased to a peak hardness, and then re-decreased with retrogression treatment. It was found that the hardness of 2nd-step aged specimen was further increased by 3rd step aging treatment($120^{\circ}C$x24h). The initial decrease in hardness during 2nd-step aging was due to the partial dissolution of pre-existing GP zone, the major precipitation hardening phase at T6 condition. It was confirmed that the major precipitation hardening phase at 3rd-step aging was GP zone and η' phase. The electrical conductivity increased continually through 2nd-step and 3rd-step aging treatment. It was conclude that the optium 2nd-step aging condition was at $175^{\circ}C$ for 50min by considering the hardness and electrical conductivity.

• Resources Recycling
• /
• v.18 no.4
• /
• pp.24-30
• /
• 2009

Rare earth based calcium aluminate phosphor ($CaAl_2O_4:Eu^{2+}$, $Nd^{3+}$) supported $TiO_2$ nanoparticles are synthesized by using sol-gel method, which are further characterized using powder X-ray diffraction (XRD), fourier transform infrared (FT-IR), diffuse reflectance UV-Visible spectroscopy (DRS UV-Vis) and transmission electron microscopy (TEM). The XRD pattern of as-prepared and sintered phosphor supported $TiO_2$ does not show the tendency to change the crystal structure from anatase to rutile phase up to $600^{\circ}C$. This indicates that the phosphor support might inhibit the densification and crystallite growth by providing dissimilar boundaries. The diffuse reflectance spectral (DRS) measurements showed shift towards longer wavelength indicating reduction in the band-gap energy as compared to free $TiO_2$. The FT-IR spectra of phosphor supported $TiO_2$ nanoparticles show shift in the peak positions to lower wavelengths. This indicates that the $TiO_2$ nanoparticles are not free, but covalently bonded to the phosphor support. TEM micrographs show presence of crystalline and spherical $TiO_2$ nanoparticles (8 - 15 nm diameter) dispersed uniformly on the surface of phosphor.

• Research in Plant Disease
• /
• v.8 no.2
• /
• pp.92-100
• /
• 2002

For the survey of viruses infected in peanut cultivated in Korea, peanut seeds and leaves showing viral symptoms were collected from their growing areas. Typical symptoms on virus infected peanut leaves including mosaic, mottle with necrosis, yellowing, stripe or vein banding and stunts were observed. Two viruses isolated from the naturally infected peanuts were identified as Bean common mosaic virus(BCMV-PSt) and Peanut mottle virus(PeMoV) by their host range, immunosorbent elcetron microscopy(ISEM), direct immuno staining assay(DISA), RT-PCR, and intracellural symptoms. Direct negative staining method by electron microscope showed filamentous particles of about 780 m in length as well as inclusion bodies. In ultrathin sections of BCMV-PSt and PeMoV infected tissues, cytoplasmic cylindrical inclusions as well as filamentous virus particles were observed in the cytoplasm of parenchyma cells. ISEM revealed filamentous particles strongly decorated with antiserums of BCMV-PSt and PeMoV Peanut seeds were stained with BCMV-PSt and PeMoV antisera indicating the possibility of seed transmission far these viruses. Seedlings germinated from peanut seeds which reacted with antiserums of BCMV-PSt by DISA showed mild mottle or stripe symptoms while mosaic and necrotic mottle symptoms were observed for PeMoV-positive seedlings. Filamentous particles were strongly decorated with each antiserum under ISEM observation. BCMV-PSt coat protein gene of about 1.2 Kbp was amplified by RT-PCR. Altogether these results indicate that BCMV-PSt is the most prevalent virus infecting peanut in Korea.

• Applied Chemistry for Engineering
• /
• v.20 no.5
• /
• pp.493-499
• /
• 2009

The properties of polystyrene and styrenic copolymer nanocomposites containing carbon nanotubes (CNT) and nanoclays were studied. Polystyrene and styrenic copolymer containing styrene and vinylbenzyl trimethylammonium chloride (SVTAC) were synthesized by emulsion polymerization. Polystyrene/CNT/clay and SVTAC/CNT/clay nanocomposites with various concentrations of CNT and different types of clay were prepared via mixing of polystyrene emulsion and clay. SVTAC/CNT nanocomposites showed a better electrical conductivity than PS/CNT nanocomposites. Nanocomposites with more surfactant during polymerization showed a better electrical conductivity than the ones with less surfactant. These indicated the positive effect of comonomer and surfactant on the electrical conductivity. Transmission electron microscopy (TEM) was used to analyze the state of CNT dispersion. TEM results showed that CNT loading, comonomer composition and amount of surfactant affected the final dispersion of CNT in nanocomposites. In order to confirm the effects of CNT loading, comonomer composition and the amount of surfactant on the thermal and dynamic mechanical properties, DSC and DMA analyses were conducted.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.30 no.2
• /
• pp.153-162
• /
• 2020

Objectives: 3D printing technologies have become widely developed and are increasingly being used for a variety of purposes. Recently, the evaluation of 3D printing operations has been conducted through chamber test studies, and actual workplace studies have yet to be completed. Therefore, the objective of this study was to determine the emission of volatile organic compounds(VOCs), metals, and particles from printing operations at a workplace. This included monitoring conducted at a commercial 3D printing service workplace where the processes involved material extrusion, material jetting, binder jetting, vat photo polymerization, and powder bed fusion. Methods: Area samples were collected with using a Tenax TA tube for VOC emission and MCE filter for metals in the workplace. For particle monitoring, Mini Particle Samplers(MPS) were also placed in the printer, indoor work area, and outdoor area. The objective was to analyze and identify particles' size, morphology, and chemical composition using transmission electron microscopy with energy dispersive spectroscopy(TEM-EDS) in the workplace. Results: The monitoring revealed that the concentration of VOCs and metals generated during the 3D printing process was low. However, it also revealed that within the 3D printing area, the highest concentration of total volatile organic compounds(TVOC) was 4,164 ppb at the vat photopolymerization 3D printing workplace, and the lowest was 148 ppb at the material extrusion 3D printing workplace. For the metals monitoring, chromium, which, is carcinogenic for humans, was detected in the workplace. As a characteristic of the particles, nano-sized particles were also found during the monitoring, but most of them were agglomerated with large and small particles. Conclusions: Based on the monitoring conducted at the commercial 3D printing operation, the results revealed that the concentration of VOCs and metals in the workplace were within Korea's occupational exposure limits. However, due to the emission of nano-sized particles during 3D printing operations, it was recommended that the exposure to VOCs and metals in the workplace should be minimized out of concern for workers' health. It was also shown that the characteristics of particles emitted from 3D printing operations may spread widely within an indoor workplace.

• Journal of Surface Science and Engineering
• /
• v.50 no.1
• /
• pp.35-41
• /
• 2017

$TiO_2$, $Al_2O_3$, and $TiO_2-Al_2O_3$ nanolaminated films were grown by atomic layer deposition (ALD) on the 316L stainless steel (SS316L) substrates at a temperature of $150^{\circ}C$. The growth kinetics of $ALD-TiO_2$ and $Al_2O_3$ thin films were systematically investigated in order to precisely control the thickness of each layers in the $TiO_2-Al_2O_3$ nanolaminated films using a high-resolution transmission electron microscopy. And, the exact deposition rates of $ALD-TiO_2$ on $Al_2O_3$ surface and $ALD-Al_2O_3$ on $TiO_2$ surface were revealed to be 0.0284 nm/cycle and 0.11 nm/cycle, respectively. At given growth conditions, the microstructures of $TiO_2$, $Al_2O_3$ and $TiO_2-Al_2O_3$ nanolaminated films were amorphous. The potentiodynamic polarization test revealed that the $TiO_2-Al_2O_3$ nanolaminated film coated SS316L had a best corrosion resistance, although all ALDcoated SS316L exhibited a clear improvement of the corrosion resistance compared with a bare SS316L.

• Journal of Life Science
• /
• v.24 no.7
• /
• pp.721-727
• /
• 2014

Mushroom-derived ${\beta}$-glucan, a polysaccharide (GLP) isolated from the mycelium of Ganoderma lucidum, was previously shown to have inhibitory effects against tumor-bearing mice in vivo. We investigated the apoptotic effect of mushroom-derived ${\beta}$-glucan in a sarcoma-180 tumor cell- bearing mice model using an ELISA to determine the levels of tumor necrosis factor-${\alpha}$ (TNF-${\alpha}$) in the mice. The morphology of the tumor cells was assessed with transmission electron microscopy (TEM). GLP was injected into the tumor-bearing mice at a dose (i.p.) of 20 mg/kg for 10 days. After 30 days, the tumor mass from the inguinal region was collected, weighed, and assayed using TEM and a TNF-${\alpha}$ ELISA kit. The tumors that developed in the mice treated with GLP were 71.4% smaller than those in the control group, showing the ability of GLP to inhibit tumor growth. The levels of TNF-${\alpha}$ in the serum of the sarcoma-180 bearing mice were 12 times greater than in the serum of the nonbearing tumor mice. An ultrastructural study demonstrated that the GLP-treated sarcoma-180 tumor cells were condensed, with rearranged chromatin. In addition, the marginated chromatin in nucleus induced the nuclear compartment, and there were many vacuolization in the cell. GLP could be an effective apoptosis-inducing compound in sarcoma-type cancers.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.112-117
• /
• 2012

With the development of nanotechnology, nano-consumer products have been popularized. For the past 10 years, potential risk of nanomaterials to human and environment have been raised carefully. Especially, workers, who directly handle nanomaterials in laboratories and manfacturers, will lead to direct exposure of nanomaterials. Therefore, direct exposure assessment and field monitoring of nanomaterials are required to assess and manage the nanomaterial exposure to human and environment. In this work, two nano-manufacturing companies, which had plasma and sol-gel processes, were selected to analyze the main exposure source and process with in-situ SMPS (scanning mobility particle sizer) and ex-situ TEM (transmission electron microscopy). The results showed that the colloidal nanoparticle in liquid phase was easily evaporated and monitored by SMPS. Most serious thing is that the workers does not know about the potential risk of nanomaterials, and thus they are not taking proper protection activities, such as PPE (personal protective equipment). Therefore, exposure assessment for nanomaterial handling facilities should be additionally carried out, and nano-safety management protocols are also provided.