• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.19-27
• /
• 2018

In this study, a numerical study was conducted to characterize the E-D nozzle which changes according to the nozzle pressure ratios. Three different numerical analysis models were designed by changing the pintle inflection angles. When the nozzle pressure ratio is low, the outside air flows into the E-D nozzle to form an open flow field. As the nozzle pressure ratio increases, the flow transition occurs to become the closed flow field where the recirculation region is isolated inside the nozzle. Also, the highest thrust coefficient was obtained in the analytical model with high pintle inflection angle at all nozzle pressure ratios.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.11
• /
• pp.952-962
• /
• 2015

Various types of altitude compensation nozzles have been investigated to develop an effective propulsion system. In order to obtain baseline data for future study of dual bell nozzles, main characteristics and key parameters of dual bell nozzles are summarized and described by analysing DLR dual bell nozzles. DLR's experimental researches show that inflection angle is proportional to transition NPR, and extension length is proportional to side load, but inversely proportional to transition NPR and transition duration. Therefore, the nozzle geometry can be determined through the performance prediction process and thus the optimization process is required to meet performance requirements between parameters.

• 한국전산유체공학회:학술대회논문집
• /
• 1997.10a
• /
• pp.66-72
• /
• 1997

Circular-to-rectangular transition ducts are used as exhaust components of high performance fighter aircraft with vectored thrust nozzles. Three-dimensional incompressible Navier-Stokes solver is used to analyze the transition duct. Cross sections of transition duct are defined by superelliptic equation. The grid system is generated by Non-Uniform Rational B-Spline, after generating surface grid by blending the cross sections. Good agreement between the results of the computational simulation and the experimental data is observed.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.12
• /
• pp.1359-1363
• /
• 1998

The p-fluorobenzyl radical was generated from the p-fluorotoluene and vibronically excited in a corona excited supersonic expansion with inert buffer gases. The vibronic emission spectra of the jet cooled p-fluorobenzyl radical in the D1 → D0 transition have been observed in the visible region. The spectra exhibit several low frequency sequence bands in the vicinity of the every strong vibronic band. The characteristics of the sequence bands have been examined by varying the experimental conditions such as carrier gas and nozzle size to identify the origin of the transition in the spectra.

• Journal of the Korean Society of Visualization
• /
• v.9 no.2
• /
• pp.61-65
• /
• 2011

Several previous works on rocket nozzle flows have revealed the existence of the transition from FSS to RSS and the occurrence of asymmetric flow associated with the boundary layer separation, which can cause excessive side-loads of the propulsion system. Thus, it is of practical importance to investigate the asymmetric flow behaviors of the propulsion nozzle and to develop its control method. In the present study, the asymmetric flow control method using a cavity system was applied to supersonic nozzle flow. Time-dependent asymmetric flow was experimentally investigated with the rate of change of the nozzle pressure ratio. The results obtained showed that the cavity system installed on nozzle wall would be helpful in fixing the unsteady motions of the boundary layer separation, consequently reducing the possibility of the occurrence of the asymmetric flow.

• Journal of ILASS-Korea
• /
• v.15 no.2
• /
• pp.74-82
• /
• 2010

In order to understand the behavior of transient gaseous injection used in an LPG (Liquefied Petroleum Gas) engine, turbulent incompressible transient jets with butane and propane were measured and analyzed at pressures of 1.5 bar and 2.0 bar with injector diameters of 3 mm and 5 mm. Mie-scattering method with a tracer was used, and images were processed to investigate the behavior of butane and propane jets. Distances from the nozzle to transition region were measured as $L_e/d_{inj}$=4.35~19.4, where $L_e$ and $d_{inj}$ indicate respectively a distance from nozzle to transition point and nozzle diameter. Slits and tubes around jet at near-field were introduced to measure the effect of entrainment and the diameter of jet, which revealed that the entrainment of surrounding air is significant for developing jet diameter. When the entrainment is restricted, the behavior of jet became deviating from the baseline. It was found that the virtual origin located outside of a nozzle towards jet tip within the conditions of this work, and its location was estimated as $x_o/d_{inj}$=0.56~7.25, where $x_o$ is a distance from nozzle to virtual origin.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.11
• /
• pp.1393-1402
• /
• 1997

Characteristics of the lifted flame which is generated by issuing of the fuel through the miniature nozzle, d = 0.164 mm, are studied using the planar laser induced fluorescence technique. OH radical is excited on the $Q_{1}$(8) line of the $A^{2}$.SIGMA.$^{+.leq.X2}$ .PI.(1, 0) band transition (283.55 nm) and LIF signals are captured at the bands of (0, 0) and (1, 1) transition (306 ~ 326 nm) using the filters and ICCD camera. Hydroxyl radical (OH) profile for nozzle attached flame shows that OH radical populations at the flame sides and flame tip are larger than those at the base. But for the lifted flame (tribrachial flame) case, those are larger at the flame base than at the flame tip and flame sides. The OH radical is more dense near the center line of flame base at the blowing out. This fact proves the Chung and Lee's blowout theory-blowout occurs when the flame is anchored at the flame axis. axis.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.16-27
• /
• 2018

A basic numerical analysis was performed to confirm the possibility of combining a dual bell nozzle and an Expansion-Deflection(E-D) nozzle. The dual bell nozzle was designed based on the first-stage nozzle of the Korean Space Launch Vehicle that is being developed, and the E-D nozzle concept was applied to the dual bell nozzle. The inlet condition was analyzed by applying eight types of frozen flow analysis, and k-${\omega}$ SST was selected as the turbulence model. The number of optimal grids was obtained as 240,000 through the grid sensitivity analysis. As a result, it was confirmed that the transition altitude increased owing to over-expansion when the E-D nozzle concept was applied to the dual bell nozzle, and the specific impulse gain was obtained at high altitudes compared with the KSLV-II first-stage engine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.289-292
• /
• 2008

Highly over-expanded nozzle of the rocket engines will be excited by non-axial forces due to flow separation at sea level operations. Since rocket engines are designed to produce axial thrust to power the vehicle, non-axial static and/or dynamic forces are not desirable. Several engine failures were attributed to the side loads. Present work investigate the unsteady flow in an over-expanded rocket nozzle in order to estimate side load during a shutdown/starting. Numerical computations has been carried out with density based solver on multi-block structured grid. Present solver is explicit in time and unsteady time step is calculated using dual time step approach. AUSMDV is considered as a numerical scheme for the flux calculations. One equation Spalart-Allmaras turbulence model is selected. Results presented here is for two nozzle pressure ratio i.e. 100 and 20. At 100 NPR, restricted shock separation (RSS) pattern is observed while, 20 NPR shows free shock separation (FSS) pattern. Side load is observed during the transition of separation pattern at different NPR.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.3
• /
• pp.147-152
• /
• 2002

When a liquid is supplied through a nozzle onto a relatively non-wetting inclined solid surface, a narrow rivulet forms. There exist several regimes of rivulet flow depending on various flow conditions. In this paper, the fundamental mechanism behind the transition of a linear rivulet to a droplet flow is investigated. The experiments show that the droplet flow emerges due to the necking of a liquid thread near the nozzle. Based on the observation, it is argued that when the retraction velocity of a liquid thread exceeds its axial velocity, the bifurcation of the liquid thread occurs, and this argument is experimentally verified.