• Journal of Energy Engineering
• /
• v.21 no.2
• /
• pp.187-193
• /
• 2012

In this study, it was experimentally investigated the effect of the clearances distance between the rod and the impinging plate on characteristics of the thermal flow. For the heat transfer enhancement of wall jet region, the right triangle and the square rods were arranged in front of the impinging plate with various clearance distances. As results, the heat transfer enhancement rate of potential core region at H/B=2 was higher than that of transition region at H/B=10. In this experiment range, the maximum heat transfer enhancement rate was about 46 % higher at the square rod with H/B=2 and C=1mm compared with the flat plate. The heat transfer enhancement rate of the right triangle rod was on average about 3 to 8 % higher than that of the square rod, regardless of the clearance.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3386-3394
• /
• 1994

An experimental study has been performed on the flow over a rotating disk, where the diameter of the disk is 500 mm and the maximum vertical deviation of the upper surface is $50 \mu{m}$ for the whole range of the angular velocity up to 3400 rpm. The flow visualization experiment for the wall jet flow induced by impinging circular jet is carried out using schlieren system and measurements are made by 3-hole and 5-hole pitot tubes. Schlieren photographs show that as the rotating speed increases the wall jet flow becomes more stable and the size of the largest eddies becomes smaller. Measurements for impinging jet flow on the stationary disk verify the accuracy of the present experiment, and those for free rotating disk flow display the existence of transition region from laminar to turbulent flows. Measurements for impinging jet flow on the rotating disk exhibit the interaction between the wall jet and the viscous pumping effect, which explains the decay in size of turbulent eddies illustrated by the schlieren photographs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1049-1055
• /
• 2004

Chemical Mechanical Polishing (CMP) is referred to as a three body tribological system, because it includes two solids in relative motion and the CMP slurry. On the assumption that the abrasives between the pad and the wafer could be a major reason not only for the friction force but also for material removal during polishing, the friction force generated during CMP process was investigated with the change of abrasive size and concentration of CMP slurry. The threshold point of average coefficient of friction (COF) with increase in abrasives concentration during interlayer dielectric (ILD) CMP was found experimentally and verified mathematically based on contact mechanics. The predictable models, Mode I (wafer is in contact with abrasives and pad) and Mode II (wafer is in contact with abrasives only), were proposed and used to explain the threshold point. The average COF value increased in the low abrasives concentration region which might be explained by Mode I. In contrast the average COF value decreased at high abrasives concentration which might be regarded to as Mode II. The threshold point observed seemed to be due to the transition from Mode I to Mode II. The tendency of threshold point with the variation of abrasive size was studied. The increase of particle radius could cause contact status to reach transition area faster. The correlation between COF and material removal rate was also investigated from the tribological and energetic point of view. Due to the energy loss by vibration of polishing equipment, COF value is not proportional to the material removal rate in this experiment.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.34 no.4
• /
• pp.144-152
• /
• 1985

This paper temperature gradient thermally stimulated surface potentian (TG-TSSP) in measurements are applied to the study of the polarity of trapped and ionic carriers in cross-linked polyethylene (XLPE) filsm. In the thermally stimulated current in uniform temperature (TSC) of XLPE five peaks appear as indicated of the A B C D and E. In this paper A (at about -120$^{\circ}C$) D (at about 70$^{\circ}C$) and E (at about 110$^{\circ}C$) peaks are investigated. A peak is due to the biassing voltage and biassing temperature. Appear in to the glass transition temperature territory and caused in to the polarization of dipole. D peak is due to the depolarization of ionic space charge and E peak due to the detrapping of carriers injected from the electrodes. TG-TSSP and TSSP are measured to study the polarity of ionic carrier (D peak). In the unsatureated region of ionic space charge polarization, TG-TSSP is lower than TSSP during the initial stage of heating. Result of the experiment for E peak, TG-TSSP is higher than TSSP during the initial stage of heating and these results do not depend on the polarity of biassing voltage, and E peak is concerned with positive carriers (Holes).

• The KSFM Journal of Fluid Machinery
• /
• v.5 no.4 s.17
• /
• pp.54-60
• /
• 2002

Experimental study was conducted to obtain the air velocity profiles in turbulent pipe flow. The acrylic smooth pipe (${\phi}=80mm$) was used for the test section of the flow loop. It was known that the velocity profiles of turbulent flow were different with Reynolds numbers and the viscous sublayer was usually quite thin. The following conclusions were drawn from the experimental investigations. Maximum velocity of the pipe center and flow-rate are useful for the duct design on the spot. The velocity profiles of high Reynolds number was flatter than those of low Reynolds number. It was known that the exponent, n, for power-law velocity profiles was $6{\sim}9$ depending on Reynolds number ranging from $10^4$ to $10^5$ in the turbulent flow, However, in this experiment study, it was $9{\sim}14$ depending on Reynolds number ranging from 17,000 to 123,727 in the turbulent flow, and $1.7{\sim}3.5$ depending on Reynolds number ranging from 2,442 to 4,564 in the transition region.

• Journal of the Mineralogical Society of Korea
• /
• v.16 no.2
• /
• pp.161-169
• /
• 2003

A phase transformation study on a synthetic amorphous diopside, $(Ca,Mg)SiO_3$has been carried out up to ∼30 GPa, and ∼$1000^{\circ}C$ using a diamond anvil cell and YAG laser heating system, respectively. A starting amorphous material shows a direct transition to cubic $(Ca,Mg)SiO_3$perovskite at high pressure, which contradicts to the crystalline diopside phase transformation sequence disproportionating into mixtures of the orthorhombic$ MgSiO_3$perovskite and the cubic $CaSiO_3$perovskite phases. This discrepancy might be due to the different starting materials as well as the temperature variations at each specific experiment performed. The present phase transfor mation sequence would modify the mineralogical assemblage in the Earth transition region and the lower mantle depending upon the pressure, temperature and the oxygen partial pressure.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.186-186
• /
• 2017

Relay intercropping system of direct seeded rice and winter cereal is labor saving cultivation and has high land use efficiency in Japan. In this system, rice seeds are direct seeded into inter-row space of winter cereals (wheat or barley) in March or April. If the direct seeding of rice is conducted before stem elongation phase or using suitable seeder, these are little effect to yield of winter cereals. Though the seeds are generally thiuram treated, it's a matter that seedling establishment rate (SER) of direct seeded rice is low and unstable. The cause of low SER has not been revealed. In present study, with the aim to reveal causes of low SER, we conducted experiments and investigated the SER, and analyzed some factors that might affect SER. Experiment1: In 2015, 2016, we buried rice seeds underground, and investigated the transition of the seed survival rates (SSR). Seeds were thiuram-treated or non-treated. In 2 periods, SSR of thiuram-treated seeds were significantly higher than non-treated seeds. In 2016, thiuram-treated seeds were high in SSR (almost 75%) at April 30th, but low SER (10~27%) after harvest of winter cereals. Therefore, almost all of seed death might have been happen after germination. Analysis 1: We investigated the SER and cultivation conditions in Ibaraki pref. for several years. Meteorological factors were referred from the nearest point of AMeDAS. From mean temperature (MT) among 5days after and before the day, we divided the period of seeding ~June 20 to phase1~4. We defined each phase as below; Phase1: $MT{\leq}10^{\circ}C$, Phase2: $10^{\circ}C<MT{\leq}15^{\circ}C$, Phase3:$15^{\circ}C<MT{\leq}20^{\circ}C$, Phase4: $MT>20^{\circ}C$. We analyzed the correlation of SER and meteorological factors by each phase. Total number of days in phase 1~4 was significantly negative correlated with SER. In phase1, total rain fall and number of soil wetting days were significantly negative correlated with SER. In phase2~4, only MT was significantly positive correlated with SER. This result suggested that rainfalls in phase1 declined seed vigor to emergence from soil surface, by repeated water absorption and re-dry. From these present studies, it was suggested that one of factors of low SER of direct seeded rice in relay intercropping system is changing of water condition by rainfalls in phase1 ($MT{\leq}10^{\circ}C$). To improve SER, it's necessary to consider something seed treatments such as prevent water absorption during phase1. However, 58~60% of seeds seemed to die during May. It's suggested that, if seeds are thiuram treated, almost all of seeds can germinate underground, but the seed vigor to emergence from soil surface are insufficient. Further studies are needed to reveal the rest causes that is happening during emergence from soil surface.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.8
• /
• pp.611-615
• /
• 2009

Due to the popular use of digital camera, a great number of photos are taken at every usage of camera. It is essential to reveal relationship between photos to manage digital photos efficiently. We propose a method that tessellates image into unit blocks and applies 2D alignment to extend content-based similar region from seed block pair having high similarity. Through an alignment, we can get a block region scoring best matching value on whole image. The method can distinguish whether photos are sharing the same object or background. Our result is less sensitive to transition or pause change of objects. In experiment, we show how our alignment method is applied to real photo and necessities for further research like photo clustering and massive photo management.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.4 s.316
• /
• pp.17-25
• /
• 2007

Multilevel inkjet printer employs multiple ink droplets with variable dot size and/or different concentrations intended to preserve high fidelity color reproduction and the appearance of continuous tone. A variety of research efforts on multitoning techniques has progressed toward better image quality. However, banding artifacts appear due to the same dot distributions near the printable output levels. This results in discontinuity and visually unpleasing output, especially at the smooth tone transition region. In this paper, to reduce the banding artifacts, a multitoning method to arrange ink distribution by controlling the blending proportion of adjacent output pixels based on an improved threshold scaling function is proposed. Ink distributions across the banding regions are changed according to two factors of the threshold scaling function because these factors handle the blending point of adjacent output pixel. Therefore, 8 observers, subjectively investigated ink distributions around the printable output levels for a set of the improved threshold scaling function. For a threshold scaling function with the specific factor values, we can achieve smoother visual transition. In the experiment, the proposed method showed a reduction of banding artifacts in both u-ay and color image and represented better Performance of color reproduction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.167-168
• /
• 2007

$CdIn_2S_4$ (110) films were grown on semi-insulating GaAs (100) by a hot wall epitaxy method. Using photocurrent (PC) measurement, the PC spectra in the temperature range of 30 and 10 K appeared as three peaks in the short wavelength region. It was found that three peaks, A-, B-, and C-excitons, correspond to the intrinsic transition from the valence band states of ${\Gamma}_4(z),\;{\Gamma}_5(x),\;and\;{\Gamma}_5(y)$ to the exciton below the conduction band state of ${\Gamma}_1(s)$, respectively. The 0.122 eV crystal field splitting and the 0.017 eV spin orbit splitting were obtained. Thus, the temperature dependence of the optical band gap obtained from the PC measurement was well described by $E_g$(T)=2.7116eV - $(7.65{\times}10^{-4}\;eV/K)T^2$/(425+T). But, the behavior of the PC was different from that generally observed in other semiconductors. The PC intensities decreased with decreasing temperature. This phenomenon had ever been reported at a PC experiment on the bulk crystals grown by the Bridgman method. From the relation of log $J_{ph}$ vs 1/T, where $J_{ph}$ is the PC density, two dominant levels were observed, one at high temperatures and the other at low temperatures. Consequently, the trapping centers due to native defects in the $CdIn_2S_4$ film were suggested to be the causes of the decrease in the PC signal with decreasing temperature.