• International Journal of Air-Conditioning and Refrigeration
• /
• 제8권1호
• /
• pp.29-39
• /
• 2000

A series of tests were performed to verify the transient characteristics of heat pump in heating and cooling mode when operating speed was varied over the 30 to 102Hz. One of the major issues that has not been addressed so far is transient characteristics during speed modulation. The model for cycle simulation has been developed to predict the cycle performance under conditions of decreasing drive frequency and the results of the theoretical study were compared with the results of the experimental study. The simulated results were in good agreement with the experimental result within 10%. The transient cycle migration of the liquid state refrigerant causes significant dynamic change in system. Thus, the migration of refrigerant was the most important factor whenever do experimental results analysis or develop simulation model.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 ICEIC The International Conference on Electronics Informations and Communications
• /
• pp.209-212
• /
• 2004

In this paper, The stress induced leakage currents of thin silicon oxides is investigated in the nano scale structure implementation for Soc. The stress and transient currents associated with the on and off time of applied voltage were used to measure the distribution of high voltage stress induced traps in thin silicon oxide films. The stress and transient currents were due to the charging and discharging of traps generated by high stress voltage in the silicon oxides. The channel current for the thickness dependence of stress current, transient current, and stress induced leakage currents has been measured in oxides with thicknesses between $41\square\;and\;113.4\square,$ which have the channel width x length 10x1um, respectively. The stress induced leakage currents will affect data retention and the stress current, transient current is used to estimate to fundamental limitations on oxide thicknesses. The weight value of synapse transistor was caused by the bias conditions. Excitatory state and inhitory state according to weighted values affected the channel current. The stress induced leakage currents affected excitatory state and inhitory state.

• 대한전자공학회논문지TE
• /
• 제39권4호
• /
• pp.335-340
• /
• 2002

본 논문에서 얇은 실리콘 산화막의 스트레스 유기 누설전류는 나노 구조를 갖는 트랜지스터의 ULSI 실현을 위하여 조사하였다. 인가전압의 온 오프 시간에 따른 스트레스전류와 전이전류는 실리콘 산화막에 고전압 스트레스 유기 트랩분포를 측정하기 위하여 사용하였다. 스트레스전류와 전이전류는 고스트레스 전압에 의해 발생된 트랩의 충방전과 양계면 가까이에 발생된 트랩의 터널링에 기인한다. 스트레스 유기 누설전류는 전기적으로 기록 및 소거를 실행하는 메모리 소자에서 데이터 유지 능력에 영향이 있음을 알았다. 스트레스전류, 전이전류 그리고 스트레스 유기 누설전류의 두께 의존성에 따른 산화막 전류는 게이트 면적이 10/sup －3/㎠인 113.4Å에서 814Å까지의 산화막 두께를 갖는 소자에서 측정하였다. 스트레스 유기 누설전류, 스트레스전류, 그리고 전이전류는 데이터 유지를 위한 산화막 두께의 한계에 대해 연구 조사하였다.

• ETRI Journal
• /
• 제3권4호
• /
• pp.93-97
• /
• 1981

• 전력전자학회논문지
• /
• 제7권3호
• /
• pp.303-312
• /
• 2002

본 논문에서는 병렬 운전 PWM 컨버터의 고성능 제어를 위하여 우수한 성능을 나타내는 퍼지 제어기를 제안하고 구현하였으며, 제안된 고성능 퍼지 제어기와 Pl 제어기와의 특성 비교를 위하여 PI 제어기도 구현하였다. 시뮬레이션과 실험 결과를 통하여, 특히 부하 급변시 병렬 PWM 컨버터의 U전압 과도응답 특성과 전류제어 과도응답 특성이 기존의 PI 제어기에 비해 제안된 퍼지 제어기가 우수한 특성을 나타내고 있음을 확인하였다. 제안된 퍼지 제어기의 우수한 특성을 입증하고 실제 제품에 적용하기 위하여 7.5kW PWM 컨버터 2대를 병렬 연결한 15kW PWM 컨버터를 구현하고 실험하였다.

• Journal of Power Electronics
• /
• 제14권2호
• /
• pp.392-401
• /
• 2014

A fast-transient repetitive control strategy for a three-phase shunt active power filter is presented in this study to improve dynamic performance without sacrificing steady-state accuracy. The proposed approach requires one-sixth of the fundamental period required by conventional repetitive control methods as the repetitive control time delay in the synchronous reference frames. Therefore, the proposed method allows the system to achieve a fast dynamic response, and the program occupies minimal storage space. A proportional-integral regulator is also added to the current control loop to eliminate arbitrary-order harmonics and ensure system stability under severe harmonic distortion conditions. The design process of the corrector in the fast-transient repetitive controller is also presented in detail. The LCL filter resonance problem is avoided by the appropriately designed corrector, which increases the margin of system stability and maintains the original compensation current tracking accuracy. Finally, experimental results are presented to verify the feasibility of the proposed strategy.

• Journal of Power Electronics
• /
• 제16권4호
• /
• pp.1256-1267
• /
• 2016

Distributed stray inductance exerts a significant influence on the turn-off voltages of power switching devices. Therefore, the design of low stray inductance bus bars has become an important part of the design of high-power converters. In this study, we first analyze the operational principle and switching transient of a T-type converter. Then, we obtain the commutation circuit, categorize the stray inductance of the circuit, and study the influence of the different types of stray inductance on the turn-off voltages of switching devices. According to the current distribution of the commutation circuit, as well as the conditions for realizing laminated bus bars, we laminate the bus bar of the converter by integrating the practical structure of a capacitor bank and a power module. As a result, the stray inductance of the bus bar is reduced, and the stray inductance in the commutation circuit of the converter is reduced to more than half. Finally, a 10 kVA experimental prototype of a T-type converter is built to verify the effectiveness of the designed laminated bus bar in restraining the turn-off voltage spike of the switching devices in the converter.

• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1851-1863
• /
• 2017

Interior permanent magnet synchronous motor (IPMSM) is most commonly used in the automotive industry as a traction motor for electric vehicle (EV). In electric vehicle, the torque output rapidly changes according to the operation of the accelerator and the braking of the driver. The transient torques are thus generated very frequently in accordance with the variable speed control of the driver. Therefore, in this paper, a method for improving the torque response in the transient states of IPMSM is proposed. In order to complement the disadvantages of the conventional PI current controller in the field oriented control (FOC), the finite-state model predictive current control and 2D-LUT is applied to improve the torque response at the torque transient period. Simulation and experiment results are given to verify the reliability of the proposed method.

• Journal of Power Electronics
• /
• 제13권5호
• /
• pp.829-840
• /
• 2013

The modified sinusoidal pulse-width modulation (SPWM) is one of the PWM techniques used in three-phase AC-DC buck converters. The modified SPWM works without the current sensor (the converter is current sensorless), improves production of sinusoidal AC current, enables obtainment of near-unity power factor, and controls output voltage through modulation gain (ranging from 0 to 1). The main problem of the modified SPWM is the huge starting current and voltage (during transient) that results from a large step change from the reference voltage. When the load changes, the output voltage significantly drops (through switching losses and non-ideal converter elements). The single-input single-output (SISO) approach with minor-loop voltage feedback controller presented here overcomes this problem. This approach is created on a theoretical linear model and verified by discrete-model simulation on MATLAB/Simulink. The capability and effectiveness of the SISO approach in compensating start-up current/voltage and in achieving zero steady-state error were tested for transient cases with step-changed load and step-changed reference voltage for linear and non-linear loads. Tests were done to analyze the transient performance against various controller gains. An experiment prototype was also developed for verification.

• 전자공학회논문지D
• /
• 제35D권6호
• /
• pp.37-45
• /
• 1998

본 논문에서는 본 연구진이 개발 중인 INPROS 3차원 반도체 공정 시뮬레이터 시스템에 이온주입된 불순물의 과도 확산(TED, transient enhanced diffusion) 기능을 첨가하여 수행한 계산 결과를 발표한다. 실리콘 내부에 이온주입된 불순물의 재분포를 시뮬레이션하기 위하여, 먼저 몬테카를로 방법으로 이온주입 공정을 수행하였고, 유한요소법을 이용하여 확산 공정을 수행하였다. 저온 열처리 공정에서의 붕소의 과도 확산을 확인하기 위하여, 에피 성장된 붕소 에피층에 비소와 인을 이온 주입시킨 후, 750℃의 저온에서 2시간 동안 열처리 공정을 수행하였다. 3차원 INPROS 시뮬레이터의 결과와 실험적으로 측정한 SIMS 데이터와 그 결과가 일치함을 확인하였다. INPROS의 점결함 의존성 과도 증속 확산 모델과 소자 시뮬레이터인 PISCES를 이용하여 역 단채널 길이 효과(RSCE, reverse short channel effect)를 시뮬레이션하였다.