• Journal of the Korean Ceramic Society
• /
• v.42 no.8 s.279
• /
• pp.567-574
• /
• 2005

Densification of SiC powder with additives of total amount of2, 4, 8 $wt\%$ Al-B-C was carried out by Spark Plasma Sintering (SPS). The unique features of the process are the possibilities of a very fast heating rate and a short holding time to obtain fully dense materials. The heating rate and applied pressure were kept at $100^{\circ}C/min$ and 40 MPa, while the sintering temperature and holding time varied from 1700 - $1800^{\circ}C$ for 10 - 40 min, respectively. The SPS-sintered specimens with different amount of Al-B-C at $1800^{\circ}C$ reached near-theoretical density. The $3C{\rightarrow}6H,\;15R{\rightarrow}4H$ phase transformation of SiC was enhanced by increasing the additive amount. The microstructure of SiC sintered up to $1750^{\circ}C$ consisted of fine equiaxed grains. In contrast, the growth of large elongated grains in small matrix grains was shown in sintered bodies at $1800^{\circ}C$, and the plate-like grains interlocking microstructure had been developed by increasing the holding time at $1800^{\circ}C$. The grain growth rate decreases with increasing amount of Al-B-C in SiC starting powder, however, the both of volume fraction and aspect ratio of large grains in sintered body increased.

• Journal of the Korean Ceramic Society
• /
• v.54 no.4
• /
• pp.285-291
• /
• 2017

This study investigated the effects of grain size and phase constitution on the mechanical properties of $3Y-ZrO_2$ by varying the sintering conditions. The raw powder prepared by a low-cost wet milling using the coarse solid oxide powders was sintered by both pressureless sintering and hot-pressing, respectively. As increasing holding time at $1450^{\circ}C$ for pressureless sintering, it promoted the microstructural coarsening of matrix grains and the phase transformation to tetragonal phase, whereas the bimodal microstructure embedded with abnormal $cubic-ZrO_2$ grains was observed regardless of sintering time. On the other hand, the specimens hot-pressed at $1300^{\circ}C$ for 2 h reached ~ 97% of relative density with homogeneous fine microstructure and mixed phase constitution. It was found that the proportion of untransformed monoclinic zirconia had the most adverse effect on the biaxial strength compared to the impacts of grain size and density. The pressureless sintering of the low-cost powder for prolonged sintering time to 8 h led to a decent combination of mechanical properties ($H_V=13.2GPa$, $K_{IC}=8.16MPa{\cdot}m^{1/2}$, ${\sigma}=981MPa$).

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.17 no.4
• /
• pp.350-364
• /
• 1995

As early as 1889, treatment of ostemyelitis was reported using xenogeneic demineralized bone. In 1965, Urist discovered that demineralized long bone fragment, even when implanted in nonskeletal tissue, would stimulate osteogenesis. The clinical use of demineralized bone of Oral and Maxillofacial surgery is not new. The demineralized bone implants were used for 1) interposition within osteotomy gaps, cystic detects, alveolar clefts ; 2) augmentation, over intact bone surfaces ; 3) construction of new bone within soft tissue. Demineralized bone grafts invokes a induced osteogenesis which is the transformation of host cells into osteoblasts. Demineralized bone has identified several factors that modulate the osteogeneic response : sterilization method, recipient age, particle size etc. Especially, pulverization of bone matrix may enhance its osteoinductive properties, to allow rapid, efficient bridging of large defects. the purpose of the present report was to describe the potential efficacy of demineralized allogeneic bone powder of skull of rabbits as a particle size ; 212 ${\mu}m$, 710 ${\mu}m$, 1 mm each other. Microscopic finding in our experimental studies shown that 710 ${\mu}m$ demineralized bone powder is the most potent osteogenic response, and then 212 ${\mu}m$, 1 mm size. Densitometric analysis shown that density of all group was continue to increase until 4 weeks after operation, and then continue to decrease.

• Journal of Broadcast Engineering
• /
• v.20 no.5
• /
• pp.728-737
• /
• 2015

Stitching algorithm obtain a descriptor of the feature points extracted from multiple images, and create a single image through the matching process between the each of the feature points. In this paper, a feature extraction and matching techniques for the creation of a high-speed panorama using video input is proposed. Features from Accelerated Segment Test(FAST) is used for the feature extraction at high speed. A new feature point matching process, different from the conventional method is proposed. In the matching process, by tracking region containing the feature point through the Mean shift vector required for matching is obtained. Obtained vector is used to match the extracted feature points. In order to remove the outlier, the RANdom Sample Consensus(RANSAC) method is used. By obtaining a homography transformation matrix of the two input images, a single panoramic image is generated. Through experimental results, we show that the proposed algorithm improve of speed panoramic image generation compared to than the existing method.

• Journal of Korea Foundry Society
• /
• v.29 no.6
• /
• pp.257-264
• /
• 2009

The effects of silicon and molybdenum on the temperature-dependent properties of high silicon and high molybdenum ductile cast iron were investigated. Microstructure was composed of ferrite, cell boundary complex carbide, carbide precipitated in the grain and graphite. The number and size of carbide decreased with the increase of silicon content and increased with the increase of molybdenum content, however, the size of cell boundary carbide increased above 0.81wt%Mo. The room temperature tensile strength increased with the increase of silicon and molybdenum contents. That did not increase with the latter with more than 0.8wt%. Meanwhile the high temperature tensile strength showed the similar trend to that of room temperature one, that of the specimen with 0.55wt%Mo was the highest. The $A_1$ transformation temperature increased with the silicon and molybdenum contents, and showed similar tendency with the variation of strength. It was discussed due to the solubility limit of Molybdenum in ferrite, of which value was assumed to be in the vicinity of 0.81wt%Mo. The weight after oxidation at 1,173K showed the result caused by the difference in solubility of molybdenum in the matrix. That and the thickness change after oxidation did not show any consistent trend with the silicon and molybdenum contents.

• Journal of Plant Biotechnology
• /
• v.1 no.1
• /
• pp.46-55
• /
• 1999

The expressed sequence tags(ESTs) from immature seed of rice, Oryza sativa cv Milyang 23, were partially sequenced and analyzed by homology. As of 1998, the partial sequences of about 6,600 cDNA clones were analyzed from normal and normalized immature seed cDNA libraries. About 2,200 ESTs were putatively identified by BLASTX deduced amino acid sequence homology analysis. About 20% of them were putatively identified as storage proteins. Also the clones were highly homologous to genes involved particularly in starch biosynthesis, glycolysis, signal transduction and defenses. Compared to 35% of redundancy in the ESTs of normal cDNA library, that from the substracted library was 15%. The Korea Rice Genome Network is maintained to provide the updated information of sequences, their homologies and sequence alignments of ESTs. For the stable expression of transgene in rice, diverse vectors were developed for overexpression, targeting and gene dosage effect with transit peptides (Tp) and matrix attachment region (MAR) sequence from chicken lysozyme locus. The rice calli were transformed via Agrobacterium tumefaciens LBA4404(pSB1) with the triparental mating technique and selected by herbicide resistance. The green fluorescent protein(GFP) gene in expression vector under the control of rbcS promoter-Tp was overexpressed upto 10 % of the total soluble protein. In addition, the Tp-sGFP fusion protein was properly processed during translocation into chloroplast. The expression of sGFP in the presence of MAR sequences was analyzed with Northern and immunoblot analysis. All the lines in which sGFP transgene with MAR sequence, showed position independent and copy number-dependent expression, while the lines without MAR showed the varied level of expression with the integration site. Thus the MAR sequence significantly reduced the variation in transgene expression between independent transformants.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.2
• /
• pp.143-147
• /
• 2017

In this study, a driving load measuring method has developed without utilizing WFT. To measure the driving load, we developed a three-axis load cell with a strain gage. A method to verify the performance of load cells was developed. A system to measure the input load was proposed, and it was verified by evaluation. The measurement error of the impact road surface was found to be less than 20％. However, except under impact road surface conditions, the proposed system can be applied for actual vehicle input load measurement. The influence of tire evaluation tests were carried out through the handling verification evaluation. The input load measurement methods proposed in the present study make performance verification possible without using WFT.

• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.187-192
• /
• 2007

Since wireless sensor networks (WSN) have relatively narrow bandwidth and have limited memory space. Mosaic by inlaying images transmitted by adjacent sensors can provide wider field of view and smaller storage memory. Most WSN are used for surveillance purpose, image acquisition period should be sufficiently short, so that mosaic algorithm has to be run in real time. Proposed algorithm is derived by using the fact that position of sensor nodes are fixed and known. Transformation matrix can be calculated by using distance between sensor nodes and distance between sensor nodes and predefined object. Simulation result shows that proposed algorithm provides very short processing time whereas it preserves image quality.

• Journal of the Korean Ceramic Society
• /
• v.25 no.3
• /
• pp.225-230
• /
• 1988

The strength and thermal shock resistance of $Al_2O_3-ZrO_2$ composites have been studied. The tetragonal $ZrO_2$ powder containing 1 mol.% $Y_2O_3$ and monoclinic $ZrO_2$ powder were prepared by coprecipitation method and subsequently mixed with $Al_2O_3$ powder and granulated by sieving. Duplex composites were prepared by dry mixing matrix agglomerate with 15 to 30 vol.% of dispersion agglomerate, followed by pressing and sintering at 1$600^{\circ}C$ for1 hr. These $Al_2O_3-ZrO_2$ 2 composites having heterogeneous structure showed improved thermal shock behaviors because of the microcracking and pores in dispersed granules, and compressive stresses around dispersed granules resulting from $ZrO_2$ transformation.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.2
• /
• pp.121-131
• /
• 1986

The stiffness matrix of circularly curved frame elements including the warping effects is formulated by the solutions of vlasov's differential equations, and the procedure for the elastic static analysis of curved girder systems by the displacement method is presented. The validity of this method has been demonstrated by comparing the analysis results with other solutions. And if the tangential lines of the two frame element axes connected at any nodal point coincide, the transformation to the global coordinate system can be omitted when we analyze the structures consisting of circularly curved elements. The theory introduced in this thesis can be applied with sufficient accuracy to the structures built up with horizontally circular curved frame elements which have closed or open cross sections and are symmetric to the axis perpendicular to the plane of the curvature, such as prestressed concrete box girder bridges.