• Advances in aircraft and spacecraft science
• /
• 제5권4호
• /
• pp.411-430
• /
• 2018

This computational study examines the augmentation of classic 2-D Rayleigh-$B{\acute{e}}nard$ convection by the addition of periodically-spaced transverse fins. The fins are attached to the heated base of the cavity and serve to partition the cavity into 'units' with different aspect ratios. The respective impacts upon heat transfer of the fin configuration parameters - including spacing, height, thickness and thermal conductivity - are systematically examined through numerical simulations for a range of laminar Rayleigh numbers (0 < Ra < $2{\times}10^5$) and reported in terms of an average Nusselt number. The selection of the low Rayleigh number regime is linked to likely scenarios within aerospace applications (e.g. avionics cooling) where the cavity length scale and/or gravitational acceleration is small. The net heat transfer augmentation is found to result from a combination of competing fin effects, most of which are hydrodynamic in nature. Heat transfer enhancement of up to $1.2{\times}$ that for a Rayleigh-$B{\acute{e}}nard$ cavity without fins was found to occur under favorable fin configurations. Such configurations are generally characterized by short, thin fins with half-spacings somewhat less than the convection cell diameter from classic Rayleigh-$B{\acute{e}}nard$ theory. In contrast, for unfavorable configurations, it is found that the introduction of fins can result in a significant reduction in the heat transfer performance.

• 대한기계학회논문집B
• /
• 제39권9호
• /
• pp.719-726
• /
• 2015

전열량을 늘리는 손쉬운 방법은 전열면적을 크게 하는 것이다. 본 연구에서는 세로와 가로 방향 튜브 핏치의 비(Pt/Pl)가 1.03인 광폭 루버 핀 시료의 습표면 j와 f 인자를 실험을 통하여 구하고 Pt/Pl=0.6인 일반 루버 핀 시료와 비교하였다. 동일 소비동력에서 광폭 루버 핀 시료의 전열성능이 일반 루버 핀 시료보다 1열에서 평균 16%, 2열에서 평균 29%, 3열에서 평균 38% 크게 나타났다. 이 증가량은 핀 면적의 증가량 (2.17배)에 비하면 현저히 작은데 이는 광폭 루버 핀 시료의 열전달계수와 핀 효율이 일반 루버 핀 시료의 값들보다 작기 때문이다. 핀 핏치가 j와 f 인자에 미치는 영향이 크지 않았다. 또한 튜브 열수가 증가할수록 j와 f 인자는 감소하였다. 실험 데이터를 기존 상관식과 비교하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.935-936
• /
• 2009

• 대한기계학회논문집B
• /
• 제21권5호
• /
• pp.691-699
• /
• 1997

The effects of concave hemispherical surface curvature on the local heat transfer from a turbulent round impinging jet were experimentally investigated. The liquid crystal transient method was used for these measurements. This method, which is a variation on the transient method, suddenly exposes a preheated wall to an impinging jet while video recording the response of liquid crystals for the measurement of the surface temperature. The Reynolds number ranges from Re=11,000 to 50,000, the nozzle-to- surface distance from L/d=2 to 10, and the surface curvature from D/d=6 to 12.The present results are also compared to those for the flat plate case. In the experiment, the local Nusselt numbers tend to increase in all regions with an increasing surface curvature. The maximum Nusselt number for all Reynolds numbers occurred at L/d .ident. 6 and a second maximum in the Nusselt number occurred at R/d .ident. 2 for both Re=23,000 and Re=50,000 in the case of L/d=2 and for Re=50,000 only in the case of L/d=4. Meanwhile, as the surface curvature increases, the value of the secondary maximum Nusselt number decreases. All the other cases exhibit monotonically decreasing values of the Nusselt number along the curved surface. The stagnation point Nusselt numbers are well correlated with Re, L/d, and D/d.

• 설비공학논문집
• /
• 제7권1호
• /
• pp.112-119
• /
• 1995

Measurements of the local heat transfer coeffcients on a spherically concave surface with a round impinging jet are presented. The liquid crystal transient method was used for these measurements. This method, which is a variation on the transient method, suddenly exposes a preheated wall to an impinging jet while video recording the response of liquid crystals for the measurement of the surface temperature. The Reynolds numbers used were 1,000, 23,000 and 50,000 and the nozzle-to-jet distance was L/d=2, 4, 6, 8, 10. Presented results are compared to previous measurements for flat plate. In the experiment, the local heat transfer Nusselt numbers on a concave surface are higher than those on a flat plate. Maximum Nusselt number at all region occured at L/d=6 and second maximum in the Nusselt number occured at R/d=2 for both Re=50,000 and Re=23,000 in case of L/d=2 and for only Re=50,000 in case of L/d=4. All other cases exhibit monotonically decreasing value of the Nusselt number along the curved surface.

• 한국전산유체공학회지
• /
• 제18권1호
• /
• pp.77-82
• /
• 2013

The error in measuring temperature profiles by thermocouple inside boundary layer mostly comes from the conduction heat transfer of the thermocouple. The error is not negligible when the conductivity of the thermocouple is very high. In this study, the effect of conduction heat transfer of the thermocouple on the temperature profile inside boundary layer was examined by considering both free-stream velocity and a thermocouple position. The conduction error of an E-type thermocouple was investigated by numerical analysis of three-dimensional conjugate heat transfer for various velocity profiles of boundary layer and thermocouple positions.

• 말소리와 음성과학
• /
• 제4권4호
• /
• pp.3-17
• /
• 2012

This study examines Korean speakers' production of English consonant clusters, focusing on vowel insertion. An acoustic analysis along with a statistical test was carried out to see what factors are involved in this production. The following factors were considered in the present study: phonetic properties, L1 transfer, and cluster types. Specifically, liquid types were considered to see if they cause any difference depending on C+/l/ or C+/r/ clusters in the onset in terms of vowel insertion patterns. That is, it was examined which Korean speakers produce better, C+/l/ or C+/r/ clusters. Interestingly, the result of the present experiment shows that the correct answer percent was higher in the C+/r/ onset clusters than C+/l/ onset clusters unlike Eckman's (1977) Marked Differential Hypothesis. In other words, the occurrence of the vowel insertion in C+/l/ clusters is higher than C+/r/ onset clusters. This may be attributed to L1 transfer. Furthermore, in the present study, three patterns of vowel insertion in the C+/l/ clusters were identified by implementing an acoustic analysis based on vowel duration and formant: a) vowel insertion with gemination, b) phonological epenthesis, and c) phonetic intrusion. However, phonetic intrusion mainly occurred in the C+/r/ clusters. Data were collected from 54 Korean speakers to see what factors are involved in vowel insertion patterns in the production of English consonant clusters. This study provides evidence for L1 transfer, the duration effect of /l/ in a different context, and three kinds of vowel insertion patterns in conjunction with gestural coordination by age groups.

• 대한기계학회논문집B
• /
• 제37권11호
• /
• pp.999-1007
• /
• 2013

본 연구에서는 다양한 형상의 파이프에 대한 압력강하와 열전달 특성을 수치적으로 해석하였다. 원형 파이프에서부터 타원형, 톱니형, 비틀어진 형태와 같은 다양한 형상의 파이프를 3차원으로 수치해석을 통해 비교하였다. 수치해석은 층류에서 난류영역까지 계산을 수행하였다. 파이프 유동해석은 완전발달된 영역에서 정상상태, 비압축성 RANS수식을 이용하여 계산하였다. 유동의 손실은 friction factor를 통해 비교하였고, 열전달 성능은 각 파이프 표면에서의 Colburn factor를 통해 비교하였다. 종합적인 열유동 성능평가는 Volume and Area goodness factor를 통해 평가하였다. 열전달 성능을 향상시키고 유동의 손실은 최소화하는 최적의 형상을 연구하였다.

• 소성∙가공
• /
• 제23권7호
• /
• pp.405-412
• /
• 2014

As a major type of heat exchanger, the steam generator (SG) produces steam from heat energy of a nuclear power plant reactor. The steam produced by the steam generator flows into a turbine, and plays an important role in electric power generation. The heat transfer tubes in the steam generator consist of approximately 10,000 U-shaped tubes, which perform a structural role and act as thermal boundaries. The heat transfer tubes conduct the thermal energy between the primary coolant (about $320^{\circ}C$, $157kgf/cm^2$) obtained from the reactor and the secondary coolant (about $260^{\circ}C$, $60kgf/cm^2$) as part of the secondary system. Recently, the heat transfer tubes in the steam generator of the pressurized water reactor (PWR) are primarily produced from Alloy 600 and Alloy 690 seamless tubes. As a pilot study to find process parameters for the cold U-bending process using rotary draw bending, numerical and experimental investigations were conducted to produce U-shaped tubes from long straight SUS304L seamless tubes. 3D finite element simulations were run using ABAQUS Explicit with consideration of the elastic recovery. The process parameters studied were the angular speed, the operation period and the bending angle. Experimental verifications were conducted to insure the suitability of the final U-shaped configurations with respect to both ovality and wall thickness.

• 대한기계학회논문집B
• /
• 제39권11호
• /
• pp.861-869
• /
• 2015

본 연구에서는 서로 다른 항력 모델이 원추형 유동층 연소기 내의 수력학적 특성과 열전달 현상에 미치는 영향에 대해, 입자상 유동에 대한 분자운동론을 적용한 오일러-오일러 모델을 사용하여 수치 해석적으로 연구하였다. Gidaspow 항력 모델과 Syamlal-O'Brien 항력 모델에 대해 유입 공기의 속도와 입자의 크기를 변화시키면서 연소기 내의 압력강하나 베드 팽창률 및 벽과 베드 사이의 열전달 계수의 변화를 조사하였다. 그 결과 베드의 팽창률은 속도가 증가함에 따라 커졌으며 압력강하는 속도의 증가에 따라 감소하였다. 벽과 베드 사이의 열전달 계수는 유입 속도가 증가하면 증가하고 입자의 크기가 증가하면 감소하는 것으로 나타났다. 베드의 팽창률이나 압력 강하와 같은 수력학적 특성은 항력 모델에 큰 영향을 받지 않았으나 열전달 계수는 항력 모델에 따라 차이가 나타났다.