• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.91-98
• /
• 2017

This study was conducted to optimize the spring constant and the damping coefficient, which are design parameters of the tractor cabin suspension system, to minimize the ride vibration. A 3D tractor MBD (multi-body dynamics) model with a cabin suspension system was developed using a dynamic analysis program (Recurdyn). Using the developed model and optimization algorithm, the spring constant and the damping coefficient, which are the design parameters of the cabin suspension for the tractor, was were optimized so thatto minimize the maximum overshoot for the vertical displacement of the cabin was minimized. The percent maximum overshoot of the tractor cabin was simulated for the 13 initial models, which were obtained using the ISCD-II method, and for the 3 additional SAO models presented in the optimization algorithm software. The model that represents with the smallest percent maximum overshoot among the 16 models was selected as the optimized model. The percent maximum overshoot of the optimized model was about approximately 5% lower than that of the existing model.

• Journal of Biosystems Engineering
• /
• 제38권3호
• /
• pp.171-179
• /
• 2013

Purpose: A simulator for the design and performance evaluation of a tractor with a hydro-mechanical transmission (HMT) was developed. Methods: The HMT consists of a hydro-static unit (HSU), a swash plate control system, and a planetary gear. It was modeled considering the input/output relationship of the torque and speed, and efficiency of HSU. Furthermore, a dynamic model of a tractor was developed considering the traction force, running resistance, and PTO (power take off) output power, and a tractor performance simulator was developed in the co-simulation environment of AMESim and MATLAB/Simulink. Results: The behaviors of the design parameters of the HMT tractor in the working and driving modes were investigated as follows; For the stepwise change of the drawbar load in the working mode, the tractor and engine speeds were maintained at the desired values by the engine torque and HSU stroke control. In the driving mode, the tractor followed the desired speed through the control of the engine torque and HSU stroke. In this case, the engine operated near the OOL (optimal operating line) for the minimum fuel consumption within the shift range of HMT. Conclusions: A simulator for the HMT tractor was developed. The simulations were conducted under two operation conditions. It was found that the tractor speed and the engine speed are maintained at the desired values through the control of the engine torque and the HSU stroke.

• 대한기계학회논문집A
• /
• 제38권5호
• /
• pp.551-557
• /
• 2014

본 논문은 작업 시 농업용 트랙터의 운전지원을 위한 강인한 횡방향 제어기를 제안하고자 한다. 자동차와 달리 트랙터의 조향 방식은 유압실린더를 이용함으로써 상대적으로 큰 시간지연을 가지고 있으며 작업 시 지면 환경도 일반 도로와는 다르다. 조향 액추에이터 모델을 포함하는 기구학적 트랙터 모델을 기반으로 동적 표면 제어라는 비선형 제어기법을 적용하여 조향 액추에이터의 시간지연 및 노면 경사의 변화에 강인한 횡방향 제어기를 설계한다. 마지막으로 상용 트랙터 시뮬레이터를 이용하여 마찰 계수가 일정한 주어진 노면 상태에서 조향 액추에이터의 시간 지연 변경이나 오르막 또는 내리막과 같은 지형 조건 변화에 대한 횡방향 제어기의 성능 및 강인성을 검증한다.

• 농업과학연구
• /
• 제49권4호
• /
• pp.937-948
• /
• 2022

Agricultural operations are performed in uneven environments by attaching an implement on the 3-point hitch of a tractor. A high load is thus placed on the 3-point hitch, and fatigue and failure of the hitch may occur during agricultural operations. In this study, a dynamic simulation model was developed to predict the load occurring on the eyebolt of a 3-point hitch, which is the main damaged component. The simulation model was developed and validated using agricultural data as simulation input and validation data. The dynamics model was developed using the specifications of a 78 kW class tractor. A measurement system was constructed to measure the simulation input and validation data. The simulation model was validated using a traction load on an eye bolt, which was measured during plow tillage operation. The measurement results showed that the average traction load on the left and right lower link and the top link were 8,099.97, 4,943.06, and 636.11 N, respectively. The simulation results and the measured traction load on the left eyebolt were respectively 610.30 and 597.15 N. The simulation results and measured traction load on the left eyebolt were respectively 1,179.78, and 1,145.06 N. The error between the simulation and measurement data was roughly 2% on the left eyebolt and 3% on the right eyebolt.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.1176-1185
• /
• 1993

The purpose of this study is to propose a new dynamic model of wheels and agricultural tractors through verification of the existence of " lift resistance " and "perpendicular adhesion" which also can be called " contra-retractive adhesion". The existence of these forces was proved through experiments including the development of a sensor which can measure the forces acting on a wheel accurately. Consequently " perpendicular adhesion ratio" which is defined as the ratio of the perpendicular adhesion to the distributed load was observed to be in the range of 0.05 to 0.3. This means the influence of the " lift resistance " is comparable to that of motion resistance in wheel dynamics. The perpendicular adhesion ratio was observed to decrease logarithmically with the increase of ground contact pressure, and to increase linearly with increase of the travel speed of the wheel . Some examples to express the new dynamic model compared to the conventional dynamics are explained.

• 농업과학연구
• /
• 제45권1호
• /
• pp.120-127
• /
• 2018

The rural labor force has gradually been decreasing due to the decrement of the farm population and the increment of the aging population. To solve these problems, it is necessary to develop and study autonomous agricultural machinery. Therefore, analyzing the dynamic behavior of vehicles in an autonomous agricultural environment is important. Until now, most studies on agricultural machinery, especially on ground vehicle dynamics, have been done by field tests. However, these field test methods are time consuming and costly with seasonal restrictions. A research method that can replace existing field test methods by using simulations is needed. In this study, we did basic research analyzing the effect of the travelling speed of a tractor on tire slip using simulation software. A tractor simulation model was developed based on field conditions following a straight path. The simulation was done for three ranges of speed: 20 - 30 km/h (considered the normal travelling speed range), 6 - 8 km/h (considered the plow tillage speed range) and 2 - 4 km/h (considered the rotary tillage speed range). The results of the simulation show that the slip ratio and slip angle values tended to increase as the traveling speed range of the tractor decreased. From the simulation results, it can be concluded that at low tractor speeds, it becomes more difficult to control the vehicle path. In future research, simulations will be done with various work environments such as a curved path as well as with various friction coefficient conditions, and the simulation results will be experimentally verified by applying them to an agricultural tractor.

• 농업과학연구
• /
• 제50권4호
• /
• pp.773-784
• /
• 2023

In this study, we developed a dynamic model and steering controller model for an autonomous tractor and evaluated their performance. The traction force was measured using a 6-component load cell, and the rotational speed of the wheels was monitored using proximity sensors installed on the axles. Torque sensors were employed to measure the axle torque. The PI (proportional integral) controller's coefficients were determined using the trial-error method. The coefficient of the P varied in the range of 0.1 - 0.5 and the I coefficient was determined in 3 increments of 0.01, 0.05, and 0.1. To validate the simulation model, we conducted RMS (root mean square) comparisons between the measured data of axle torque and the simulation results. The performance of the steering controller model was evaluated by analyzing the damping ratio calculated with the first and second overshoots. The average front and rear axle torque ranged from 3.29 - 3.44 and 6.98 - 7.41 kNm, respectively. The average rotational speed of the wheel ranged from 29.21 - 30.55 rpm at the front, and from 21.46 - 21.63 rpm at the rear. The steering controller model exhibited the most stable control performance when the coefficients of P and I were set at 0.5 and 0.01, respectively. The RMS analysis of the axle torque results indicated that the left and right wheel errors were approximately 1.52% and 2.61% (at front) and 7.45% and 7.28% (at rear), respectively.

• Journal of Biosystems Engineering
• /
• 제2권1호
• /
• pp.33-48
• /
• 1977

Transporting agricultural products and the other material by the two-wheel-tractor (power-tiler)and trailer system may be one of its most widely used farming functions.The safety and hitching load for all the previaling performing conditions may be the general concern over the operation of the tiller-trailer system. In this study, a mathematical model to determine the static and dynamic forces excerting on the hitch point were developed . Based on the analysis of the model and the field measurements. the limiting hitching load and critical slope were analyzed. The results of the study are summarized as follows ; 1) The limit angle of slope land for the safety steering that two-wheel tractor-single axle trailer system was able to transport agricultural products was the direct angle (${\gamma}$) = 8 ; the cross angle$\beta$) 15 ; and it was decreased in accordance with the increase of carrying load ($W_4). 2) The critical velocity for safe operation in case of running on downward hill road was about 1.08m/sec. 3) The limiting carrying load for the safe steering was W$_4$=600kg. The degree of the safe steering for different braking methods was given in order as follows ; Simulataneous braking the tractor and trailer , braking the trailer only, and braking tractor only. 4) Among the three components of impact loads excerting on the hitch point, the component in the lateral direction ($P_{Vy}$) was near zero in spite of increase of hitching load ($W_4) , while the components in the other two mutually perpedicular directions ($P_{Vx}$ and ($P_{Vz}$) ) had larger values in horizontal plane than those in the slope lands. 5) Moment of forces on the lateral direction (M$y$) had the largest value among the three components of impact moment acting on the hitch point, however all the components were sharply increased in accordance with the increase of hitching loads ($W_4. Three components of the moment were the negative values.

• 대한조선학회논문집
• /
• 제60권4호
• /
• pp.288-295
• /
• 2023

This paper deals with the dynamic simulation method for analysis of driving characteristics of aircraft and towing vehicles (TUG) on carrier vessel in wave motions. For prompt deployment in a short period of time, optimization of the movement of carrier aircraft becomes a major issue. In this regards, strategy studies using real-time simulation technology and optimal decision-making technologies are being conducted. In the present work, the dynamic characteristics of carrier aircraft and TUG connected by towbar or towbarless mechanism were investigated by means of multi-body dynamics model. Meanwhile, for real-time simulation, Dugoff's model of tire loads calculation was adopted. Through comparative analysis it was confirmed that the similarity of results between the multi-body contact model and the tire load calculation model can be achieved by coefficients tuning.

• 한국산림과학회지
• /
• 제84권2호
• /
• pp.218-225
• /
• 1995

이 논문에서는 임업용 트랙터의 집재작업 분석에 요구되는 역학분석모델을 제시하고 사례분석을 통해 적용성을 검토하였다. 역학분석모델은 크게 견인목의 역학구조해석모델, 차량하중분석모델 및 주행중인 차량의 구동력과 저항력 분석모델의 3부분으로 구성되어 있다. 사례분석에서는 가상적인 집재작업 시나리오를 만들어 역학적으로 중요하거나 혹은 집재생산성에 중요한 인자들에 대한 영향력분석을 통해 모델의 적용성을 검토하였다. 사례분석은 1) 당김줄을 견인목에 묶는 방법이 견인력에 미치는 영향, 2)주행속도 및 견인목 하중이 차륜의 동력요구에 미치는 영향, 3) 2륜구동과 4륜구동 트랙터의 견인작업 수행 성능 비교에 관한 내용을 포함한다.