• 한국기계가공학회지
• /
• 제11권2호
• /
• pp.79-84
• /
• 2012

This study consist of two parts. One is development of a self-propelling vinyl remover which was already reported at the previous paper. This is the second part of the study. For the study, an attached vinyl remover was developed. It was consisted of connecting tractor to bucket, removing bucket from tractor, and the process was the tractor's assistance hydraulics. In the case of an attached vinyl remover, the vinyl was twisted 0.5times per 30~85cm length. The bobbin's diameter was 190mm and it's stable travelling speed was 1m/s. The revolution of the remover wheel was 90rpm to maintain the wheel's linear velocity. As seen at performance test at the field which had 950mm ridge intervals and 10 a area, the average working speed was 1m/s and the turning time was 20seconds. Therefore, the working performance was 24.5min/10a. The efficiency of used vinyl remover was 97% and working conditions were good.

• Journal of Biosystems Engineering
• /
• 제32권5호
• /
• pp.292-300
• /
• 2007

Not many types of roughage cutters have been introduced in Korea so far. However, those machines could not satisfy farmers to cut rice straw or barley wrap-silage properly. Stiffness and firmness of roughage bale were two obstructing factors. In order to solve this problem, a tractor attached cut-feeding machinery for the round baled roughage was developed for dairy and beef cattle farm in Korea. A series of tests were performed and acquired data were analyzed by using the several imported roughage cutters, which have been already introduced in dairy farm in Korea. And, a prototype of forage cutter was selected, analyzed, designed and manufactured to develop a tractor attached roughage cut-feeder for round bale. Also, the prototype machine was tested, modified and improved through revising model. As a result, a tractor attached roughage cut-feeder for round bale was manufactured. In order to evaluate the performance of the model machinery. a series of test were performed by the prototype machinery both at the plant and field. The model machinery developed satisfied in both power requirement and cutting capacity. As a conclusion, one of the obstacles against feeding the round baled roughage in the korea cattle farm can be eliminated by developing the tractor attached round baled roughage cut-feeder.

• 한국분무공학회지
• /
• 제21권4호
• /
• pp.195-199
• /
• 2016

Spraying of nozzles and design of tractor-attached boom sprayers have been studied for analysis of liquid spraying features. The following conclusions have been drawn. At all pressures, twin flat spray tips was finer than flat spray tips. A fine spray with VMD of 101 to 200 appeared at 1.5MPa. So, it was selected as the boom sprayer nozzle. In spraying uniformity analysis, Type B was proven to have more uniformity than Type A and Type C at 52.0 cm attached distance. Type A and Type C were proven to have more uniformity than Type B at 58.5 cm attached distance. It is concluded that these results reflect atomizing characteristics of nozzles during pest control with tractor-attached boom sprayer. Therefore, optimum setting will be putting Type C with 58.5 cm distance.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2005년도 하계 학술대회 논문집
• /
• pp.80-88
• /
• 2005

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2005년도 하계 학술대회 논문집
• /
• pp.89-94
• /
• 2005

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.569-581
• /
• 1996

A microcomputer -based data acquistion system was designed and developed at Michigan State University , USA to conduct field data studies. The system designed for the research carried out used an Apple IIe microcomputer for collecting data on-board the tractor. An AII3 Analog to Digital (A/D_ convertor was chosen to interface each analog signal to the microcomputer. A commercially available Dj TPM II was employed to display information such as an engine speed, ground speed, percent drive wheel slip , distance travelled and area covered per hour. The frequency output from the radar unit was channeled through a frequency to voltage (F/V) convertor , so that AII3 Analog to Digital (A/D) convertor could read it. The fuel consumption was measured using on EMCO pdp-1 fuel flow meter attached to the engine fuel line. The draft of the tillage and other drag equipment was determined using strain gages attached to the drawbar of the tractor. The system was developed to collect the draft and fuel requirements for various farm equipment different kind of soils.

• 한국소음진동공학회논문집
• /
• 제26권5호
• /
• pp.584-593
• /
• 2016

In this study, an improvement design method for reducing the vibration of fenders equipped in a tractor is proposed through the establishment of a finite element model and the topology optimization. As the original shapes of the parts cannot be altered, an improved design model was derived in which a stiffener was attached to the border of parts. Thus, the first resonance frequency was increased by approximately 16 Hz, which was confirmed to be the frequency interval for avoiding the idle and operating frequency of the engine. Finally the improved design model was applied to confirm the effect of vibration reduction. Therefore, it can be concluded that the improved design model of the tractor fender is effective at reducing vibrations of the tractor fender.

• 한국농공학회지
• /
• 제15권1호
• /
• pp.2925-2933
• /
• 1973

For the efficient utilization of farm machines on the inclined uqland, work performance in plowing, harrowing and terracing and critical workable gradients were tested on three farm machines which are 47 ps-farm tractor, 8 ps-power tiller and 5 ps-power tiller. The results of this study are summarized as follows; 1) The steeper the slope of the upland was the more inefficient the work performance of all machines was. 2) The critical workable gradients of the machines were proved as 14 for 47 ps-farm tractor, 12 for 8 ps-power tiller and 10 for 5ps-power tiller. 3) Plowing in the way of turning the furrow slices against the slope in order to build up terraces, the critical workable gradients were 8 for 47 ps-farm tractor and 8 ps-power tiller and 6 for 5 ps-power tiller. 4) Two-way plow is recommended for plowing with farm tractor on inclined upland, and high lug of tire would be good to prevent the slippage, and side valance-weight should be attached to power tiller for preventing its overturning.

• 한국정보전자통신기술학회논문지
• /
• 제11권2호
• /
• pp.150-155
• /
• 2018

국내 논 작업의 기계화율은 약 90% 이상 되었지만, 밭 작업의 기계화율은 약 60%이며, 수확작업의 기계화율은 10%내외로 밭 작업의 기계화율의 제고가 필요한 실정이다. 그러므로 본 연구는 트랙터 부착 수확작업기 개발을 위한 기초연구로써 마늘, 양파 등 땅속작물수확기의 견인작업에 따른 트랙터 차축의 부하 신호를 측정하고 주행속도에 따른 차축 소요 동력을 분석하였다. 밭 작업용 트랙터 차축의 소요 동력을 측정하기 위하여 휠 센서와 데이터 수집 시스템을 설치하였으며, 두 개의 작업속도에서 견인작업을 수행하며 소요 동력을 계측하였다. 계측한 데이터는 일원 분산분석을 수행하여 트랙터 주행 속도가 차축 소요 동력에 미치는 영향을 분석하였다. 소요 동력 분석 결과, 트랙터 부착 작업기의 작업속도가 증가할수록 트랙터의 소요 동력이 증가됨을 알 수 있었으며, 트랙터 동력전달시스템의 최적설계를 위해서는 다양한 수확작업에 따른 소요동력 분석이 필요함을 알 수 있다.

• 한국작물학회지
• /
• 제47권3호
• /
• pp.157-160
• /
• 2002

삼백초의 근경 수확방법을 인력수확에서 생력기계화 수확기술로 개선코자 트랙터부착 굴취기 등 4종의 수확기기의 기계수확 효율을 비교, 검토하였던 바 그 결과를 요약하면 다음과 같다. 1. 총생력시간은 인력에 비하여 경운기 경운 60%, 경운기부착 굴취기 64%, 트랙터부착 굴취기 67%절감되었다. 2. 근경의 손실율은 인력수확 13.9%, 경운기 경운 11.7%, 경운기부착 굴취기 9.8%, 트랙터부착 굴취기 5.1%로 기계수확에서 낮았다. 3. 상품 근경수량은 인력수확 3,032 kg/10a에 비하여 경운기 경운은 248 kg 감소하였으나, 경운기부착 굴취기와 트랙터부착 굴취기는 56kg, 320kg각각 증가되었으며, 총 근경수량은 인력수확에 비하여 기계수확에서 3-10%증가되었는데, 트랙터부착 굴취기는 10%의 증가로 가장 높은 수량을 보였다. 4. 경제성은 인력수확에 비하여 기계수확에서 13-27%높았으며, 트랙터 부착 굴취기는 27%로 가장 높았다. 5. 트랙터부착 굴취기는 생력효율, 상품수량, 총 근경수량 그리고 경제성에서 가장 높거나, 많은 것으로 나타나 적용가능성이 가장 높은 것으로 나타났다.