• 농업과학연구
• /
• 제40권3호
• /
• pp.237-241
• /
• 2013

This study started to export an orchard tractor to Europe under the situations that R&D activities for orchard tractor were marginal and even it was not produced. The R&D for orchard tractor has been progressed and the most of it is accomplishing the goal. In this study, the durability of clutch friction part was tested for F/R clutch and moment of inertia of PTO clutch, and it was compared with the design criteria of transmission of tractor. According to the results of inertia test of F/R clutch, hydraulic pressures of clutch satisfied $1,961.33{\pm}196.13kPa$ of design criteria, and the variations of torque for forward and reverse operation were relatively constant. Therefore, it was found that the durability of clutch friction part was stable and reliable. Test results showed that the main hydraulic pressures were maintained $1,961.33{\pm}196.13kPa$ during the tests of moment of inertia of PTO clutch, and when it was operated, the hydraulic pressures were reached $1,961.33{\pm}196.13kPa$. Therefore, it was found that the hydraulic pressures of PTO satisfied the design criteria. By the results that the time of the hydraulic pressures of PTO reaching main hydraulic pressure, and that of torque values restoring to the original was same as the time of the first gear of PTO reaching the maximum rotational speed, it was found that PTO could transfer power to attachments as it was designed.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.91-98
• /
• 2017

This study was conducted to optimize the spring constant and the damping coefficient, which are design parameters of the tractor cabin suspension system, to minimize the ride vibration. A 3D tractor MBD (multi-body dynamics) model with a cabin suspension system was developed using a dynamic analysis program (Recurdyn). Using the developed model and optimization algorithm, the spring constant and the damping coefficient, which are the design parameters of the cabin suspension for the tractor, was were optimized so thatto minimize the maximum overshoot for the vertical displacement of the cabin was minimized. The percent maximum overshoot of the tractor cabin was simulated for the 13 initial models, which were obtained using the ISCD-II method, and for the 3 additional SAO models presented in the optimization algorithm software. The model that represents with the smallest percent maximum overshoot among the 16 models was selected as the optimized model. The percent maximum overshoot of the optimized model was about approximately 5% lower than that of the existing model.

• Journal of Biosystems Engineering
• /
• 제24권3호
• /
• pp.183-194
• /
• 1999

Using the dynamic model and simulation program TDA developed in the previous paper, effects of design parameters of an agricultural tractor-trailer system on its vertical seat vibrations were investigated. The tractor-trailer system was excited by traversing over a half-sine bump. The excitation frequencies were determined by traveling velocity of the tractor and a half-sine bump selected appropriately. TDA predicted the autospectra of the vertical seat accelerations with different values of design parameters and compared them to analyze their effects. The design parameters included positions of engine, cab, and seat mountings as well as their dynamic properties. The results of this study suggested guidelines with which an improved structure of tractor may be developed in the early stage of design for a better ride quality.

• Journal of Biosystems Engineering
• /
• 제23권6호
• /
• pp.549-560
• /
• 1998

The dynamic model of a tractor-trailer system developed in the first part of this paper was verified in this article by comparing the simulated acceleration responses of the system with actually measured ones. A commercially available tractor and a trailer were used for the verification test. Values of the model parameters were measured or theoretically derived if the measurement was practically impossible. The tractor-trailer system was operated with different forward speeds over three equally spaced half-sine bumps on the flat concrete surface. Results of the verification tests showed that autospectra of the measured and simulated accelerations of the tractor-trailer system agreed well up to the frequencies slightly feater than the fundamental frequencies of the ground excitations and at the frequencies of engine excitations. The mean of normalized errors of the simulated responses to the measured ones was estimated to be less than 10% for all the test runs. The peak responses in the autospectra also coincided well both in the frequency and magnitude.

• Journal of Biosystems Engineering
• /
• 제23권2호
• /
• pp.179-186
• /
• 1998

This study was conducted to sense posture of an autonomous tractor using a DGPS, a gyro compass, and a potentiometer. Posture sensing system was constructed and its accuracy was evaluated. The accuracy of DGPS was evaluated under stationary and moving conditions, and the performance of the gyro compass and the potentiometer was investigated by measuring bearing and steering angles, respectively. Also, the effect of DGPS interference by obstacles was evaluated experimentally. The position accuracy was about 6.6cm(95%) under the stationary condition and 10 cm at sharp turning condition. Steering angle of the tractor could be related linearly to the output of the potentiometer that was installed on the rotating center of a knuckle arm. The positioning accuracy of the DGPS varied significantly according to the number of visible GPS satellites, but was good with more than 7 satellites. The DGPS gave bad solutions for sensing the posture of tractor when signals from satellites or the correction data from the base were interfered by obstacles.

• Journal of Biosystems Engineering
• /
• 제22권1호
• /
• pp.1-10
• /
• 1997

A ratio of cosine values of two intersection angles in a tractor-rotary power driveline was established as a design criterion which must be satisfied in the range of vertical movement of the rotary with respect to the tractor. In addition tractor-rotary power driveline was analyzed and 25 design variables were Proposed. The intersection angles were also derived using the design variables. Using the design condition and variables, a computer program was developed to evaluate the performance of the driveline and to simulate the vertical movement of rotary. Several methods for searching the optimum design were also suggested.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.506-512
• /
• 2000

Performance of a four- wheel tractor fabricated by Tongyang Moolsan Co., Ltd, Korea was tested in Thailand during May-June 2000. Wheel slip and field capacity were measured in three fields using different traction devices and implements. The tractor worked satisfactorily in the test conditions. Wheel slip of 26.05-33.63 % and the field capacity of 0.17 - 0.20 ha/hr were observed during plowing operation. Further tractive performance tests using a three-point linkage configuration are recommended in Thailand field conditions. Different designs of cage wheels are recommended to be tested to optimize the tractive performance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 추계학술대회 논문집
• /
• pp.749-753
• /
• 2011

The vibration that occurs when starting the agricultural tractor is raised more than double compared to the general situation. In this case, impulsive vibration make the machine's life to be shortened, which can cause a driver's physical problems also. Therefore, in this paper, we have taken an effective way to reduce the impulsive vibration that occurs when starting a agricultural tractor. As a result, we confirmed that appling the anti-vibration pads and the high stiffness engine mounts is effective method to reduce the impulsive vibration.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.239-245
• /
• 2015

In order to control the hybrid power system efficiently, the knowledge for the required load of the system is important. The agricultural tractor performs various farm works such as plow, rotary, and baler. When it performs rotary tillage and baler operation, the generated work load is analyzed. To analyze trend of work load, moving average technique is applied to the measurement data. Optimal control inputs for the two works are obtained from simulation using the dynamic programming. The novel fundamental control strategy for parallel hybrid tractor called Max. SOC is proposed.

• 한국기계가공학회지
• /
• 제18권5호
• /
• pp.82-89
• /
• 2019

This study is a structural analysis of the major components of the implements for an agricultural tractor. To develop an unpowered high-speed implement of an agricultural tractor, the modeling and analysis of the benchmarking product was calculated using 3D scanning and reverse design technologies. The tractive load was calculated using the powertrain efficiencies and soil-propelling force, which were estimated by analyzing the main frame, disc, frames, and chisel plow for the axial loading condition. The final goal of this research is to establish the design parameters and assembly technology for securing disc harrow structures and durability of life. This information will be used to analyze the new model design for domestic consumption.