• Smart Structures and Systems
• /
• v.21 no.5
• /
• pp.677-686
• /
• 2018

The structural responses are often used to identify the structural local damages. However, it is usually difficult to gain the responses of the track, as the sensors cannot be installed on the track directly. The vehicles running on a track excite track vibration and can also serve as response receivers because the vehicle dynamic response contains the vibration information of the track. A damage identification method using the vehicle responses and sensitivity analysis is proposed for the vehicle-track coupling system in this paper. Different from most damage identification methods of vehicle-track coupling system, which require the structural responses, only the vehicle responses are required in the proposed method. The local damages are identified by a sensitivity-based model updating process. In the vehicle-track coupling system, the track is modeled as a discrete point supported Euler-Bernoulli beam, and two vehicle models are proposed to investigate the accuracy and efficiency of damage identification. The measured track irregularity is considered in the calculation of vehicle dynamic responses. The measurement noises are also considered to study their effects to the damage identification results. The identified results demonstrate that the proposed method is capable to identify the local damages of the track accurately in different noise levels with only the vehicle responses.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.112-120
• /
• 2003

In this paper, dynamic track tension fur high mobility tracked vehicle is investigated by multibody dynamic simulation techniques. This research focuses on a heavy military tracked vehicle which has sophisticated suspension and rubber bushed rack systems. In order to obtain accurate dynamic track tension of track subsystems, each track link is modeled as a body which has six degrees of freedom. A compliant bushing element is used to connect track links. Various virtual proving ground models are developed to observe dynamic changes of the track tension. Numerical studies of the dynamic track tension are validated against the experimental measurements. The effects of pre-tensions, traction forces, fuming resistances, sprocket torques, ground profiles, and vehicle speeds, for dynamic responses of track tensions are explored, respectively.

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1028-1040
• /
• 2000

A numerical method is presented for the dynamic analysis of military tracked vehicles of high mobility. To compute the impulsive dynamic contact forces which occur when a vehicle passes on a ground obstacle, the track is modeled as the combination of elastic links interconected by pin joints. The mass of each track link, the elastic elongation of a track link between pin joints by the track tension, and the elastic spring effects on the upper and lower surfaces of each track link have been considered in the equations of motion. And the chassis, torsion bar arms, and road wheels of the vehicle are modeled as the rigid multi bodies connected with kinematic constraints. The contact positions and the contact forces between the road wheels and track, and the ground and the the track are simultaneously computed with the solution of the equations of motions of the vehicle consisting of the multibodies. The iterative scheme for the solution of the multi body dynamics of the tracked vehicle is presented and the numerical simulations are conducted.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.8
• /
• pp.7-12
• /
• 2010

When a vehicle is running, wheel is generating vertical and lateral force on the rail, in addition to load of vehicle, through a complicated set of motions. The derailment coefficient refers to the ratio of lateral force to vertical force(wheel load), and if the value exceeds a certain level, a wheel climbs or jumps over the rail. That's why the value is used as a criterion for running safety. Derailment coefficient of rolling stocks alters according to shape of rail track. I measured three-dimensional angular velocity and acceleration to use 3D Motion Tracker. Test result, derailment coefficient of rolling stocks and shape of rail track examined closely that have fixed relation. Specially, was proved that roll motion has the close coupling relation.

• Structural Engineering and Mechanics
• /
• v.80 no.5
• /
• pp.491-501
• /
• 2021

A difference in subgrade settlement between two rails of a track manifests as lateral differential subgrade settlement. This settlement causes unsteadiness in the motion of trains passing through the corresponding area. To illustrate the effect of lateral differential subgrade settlement on the dynamic response of a vehicle-track coupling system, a three-dimensional vehicle-track-subgrade coupling model was formulated by combining the vehicle-track dynamics theory and the finite element method. The wheel/rail force, car body acceleration, and derailment factor are chosen as evaluation indices of the system dynamic response. The effects of the amplitude and wavelength of lateral differential subgrade settlement as well as the driving speed of the vehicle are analyzed. The study reveals the following: The dynamic responses of the vehicle-track system generally increase linearly with the driving speed when the train passes through a lateral subgrade settlement area. The wheel/rail force acting on a rail with a large settlement exceeds that on a rail with a small settlement. The dynamic responses of the vehicle-track system increase with the amplitude of the lateral differential subgrade settlement. For a 250-km/h train speed, the proposed maximum amplitude for a lateral differential settlement with a wavelength of 20 m is 10 mm. The dynamic responses of the vehicle-track system decrease with an increase in the wavelength of the lateral differential subgrade settlement. To achieve a good operation quality of a train at a 250-km/h driving speed, the wavelength of a lateral differential subgrade settlement with an amplitude of 20 mm should not be less than 15 m. Monitoring lateral differential settlements should be given more emphasis in routine high-speed railway maintenance and repairs.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.122-130
• /
• 2013

Rail geometries such as cant, grade and curvature can be easily represented by means of a track coordinate system. In this analysis, in order to derive a dynamic and constraint equation of a wheelset, the track coordinate system is used as an intermediate stage. Dynamic and constraint equations of railway vehicle bodies except the wheelset are written in the Cartesian coordinate system as a conventional method. Therefore, whole dynamic equations of a railway vehicle are derived by combining wheelset dynamic equations and dynamic equations of railway vehicle bodies. Constraint equations and constraint Jacobians are newly derived for the track coordinate system. A process for numerical analysis is suggested for the derived dynamic and constraint equations of a railway vehicle. The proposed dynamic analysis of a railway vehicle is validated by comparison against results obtained from VI-RAIL analysis.

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.1094-1099
• /
• 2002

In this paper, a numerical method for vehicle-track interaction analysis is developed to evaluate vertical dynamic force subjected to rail surface. A vehicle is modelled by lumped masses system and track by multi layered continuous beam system. The equation of motion of vehicle and track interaction system is derived by considering compatibility condition at the contact points between wheel and rail. The input vibration source is given by the empirical formula of power spectral density of track irregularity, which is suggested by FRA. Using this method, dynamic impact factors with the train speed are evaluated.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.65-70
• /
• 1998

In this paper, we developed a Windows 95 version off-line programming system which can simulate a track vehicle model in 30 graphics space. The track vehicle was adopted as an objective model. The interface between users and the off-line program system in the Windows 95's graphic user interface environment was also studied. The developing language is Microsoft Visual C++. Graphic libraries, OpenGL, by Silicon Graphics, Inc were utilized for 3D Graphics.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.201-207
• /
• 2007

At an early design stage of rail track, dynamic analyses using a standard vehicle model of ADAMS/Rail are employed. In the real field, it is very difficult to find an optimal solution on the designing of rail track considering future operating vehicles because the construction of rail track should be done in the advance of vehicle selection and operation. Using a standard vehicle model of ADAMS/Rail, however the better selection among designed rail tracks is possible by comparing the dynamic analysis.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.137-141
• /
• 1999

In this paper, we developed a Windows 95 version off-line programming system which can simulate a track vehicle model in 3D graphics space. The track vehicle was adopted as an objective model. The interface between users and the off-line program system in the Windows 95's graphic user interface environment was also studied. The developing language is Microsoft visual C++. Graphic libraries, OpenGL, by Silicon Graphics, Inc. were utilized for 3D Graphics.