• 한국군사과학기술학회지
• /
• 제25권6호
• /
• pp.553-560
• /
• 2022

This study investigates improvement of torsional strength of special wrench for K-series self-propelled howitzer power-pack maintenance. In order to maintain the power-pack, special wrench is one of the essential tools for assembling/disassemblimg the engine and transmission. However, failures(plastic deformation, fracture phenomenon and etc.) have been frequently reported even though special wrench was used within recommended standard torque range. Therefore, in this study, finite element analysis using ABAQUS was performed and modification of design parameters have been proposed. Prototypes based on the proposed parameters were manufactured and torsional experiment(torque about 130 % of recommend maximum torque) validated the newly proposed design parameters. Special wrench based on this study is applied to mass production and currently used for the maintenance.

• 대한토목학회논문집
• /
• 제8권2호
• /
• pp.125-133
• /
• 1988

RC 부재(部材)에 대한 정밀도 높은 하중이력곡선(荷重履歷曲線)의 제안은 합리적인 설계법(設計法)의 수립이라는 관점으로 볼 때 매우 중요하다. 순수비틀림을 받는 RC 부재(部材)의 비틀림모멘트와 비틀림각(角) 관계곡선을 최근 제안한 사람은 Collins, Hsu 등이다. 그러나 그의 비틀림 내력평가(耐力評價) 결과는 극한상태를 제외하고는 모든 하중영역(荷重領域)에 있어서 상당히 과소평가되고 있다. 본 연구에서는 구성방정식(構成方程式)에 콘크리트의 인장강성(引張剛性) 및 수정된 콘크리트 softening 계수(係數)를 도입하여 임의의 하중단계에서도 비틀림내력(耐力)의 정밀도를 높이는데 그 목적(目的)을 두었다. 특히 이론해석(理論解析)의 타당성을 검토하고자 14체(體)의 RC 부재(部材)를 제작하여 재하실험(載荷實驗)을 실시하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.190-193
• /
• 2003

Flexural-torsional behaviors of the typical architectural precast beam sections - inverted tee and rectangular - were compared. The inverted-tee beams were designed with a parking live load - 500kgf/$\textrm{m}^2$ and a market-1,200kgf/$\textrm{m}^2$ according to the currently used typical shape in the domestic market building site. The rectangular beams were also designed as the same bottom dimension and area, and reinforced for similar strength as in the cases of inverted tee beams. Two rectangular and two inverted precast pretensioned concrete beams were tested and analyzed

• Earthquakes and Structures
• /
• 제25권6호
• /
• pp.417-427
• /
• 2023

If the center of mass and center of stiffness or strength of a structure plan do not coincide, the structure is considered asymmetric. During an earthquake, in addition to lateral vibration, the structure experiences torsional vibration as well. Lateraltorsional coupling in asymmetric structures in the plan will increase lateral displacement at the ends of the structure plan and, as a result, uneven deformation demand in seismically resistant frames. The demand for displacement in resistant frames depends on the magnitude of transitional displacement to rotational displacement in the plan and the correlation between these two. With regard to the inability to eliminate the asymmetrical condition due to various reasons, such as architectural issues, this study has attempted to use supplemental viscous dampers to decrease the correlation between lateral and torsional acceleration or displacement in the plan. This results in an almost even demand for lateral deformation and acceleration of seismic resistant frames. On this basis, using the concept of Torsional Balance, adequate distribution of viscous dampers for the decrease of this correlation was determined by transferring the "Empirical Center of Balance" (ECB) to the geometrical center of the structure plan and thus obtaining an equal mean square value of displacement and acceleration of the plan edges. This study analyzed stiff and flexible torsional structures with one-way and two-way mass asymmetry in the Opensees software. By implementing the Particle Swarm Optimization (PSO) algorithm, the optimum formation of dampers for controlling lateral displacement and acceleration is determined. The results indicate that with the appropriate distribution of viscous dampers, not only does the lateral displacement and acceleration of structure edges decrease but the lateral displacement or acceleration of the structure edges also become equal. It is also observed that the optimized center of viscous dampers for control of displacement and acceleration of structure depends on the amount of mass eccentricity, the ratio of uncoupled torsional-to-lateral frequency, and the amount of supplemental damping ratio. Accordingly, distributions of viscous dampers in the structure plan are presented to control the structure's torsion based on the parameters mentioned.

• 한국강구조학회 논문집
• /
• 제10권4호통권37호
• /
• pp.677-689
• /
• 1998

본 연구에서는 중심압축력을 받는 스털스터드의 설계강도에 대하여 다루었으며 비교 평가하였다. 미국규준인 냉간성형 LRFD 설계규준 (AISI). 유럽의 냉간박벽부재설계규준 (EC3 part 1.3) 및 독일의 관련규정 (DASt-Richtlinie 016)의 유사성과 차이점을 소개하고 분석하며 체계적으로 평가하였다. 특히 유효폭과 전체 안정성문제 (휨좌굴과 비틀림좌굴)가 이 논문에서 내포되어 있다. 또한 예제를 통하여 두 규준인 AISI와 EC3에 의한 설계압축강도를 산정하고 비교 분석하였다.

• Structural Engineering and Mechanics
• /
• 제15권5호
• /
• pp.495-511
• /
• 2003

New material applications and transparency are desired by contemporary architects. Its superb transparency and high strength make glass a very suitable building material -in spite of its brittleness- even for primary load bearing structures. Currently we will focus on load bearing glass beams, subjected to different loading types. Since glass beams have a very slender, rectangular cross section, they are sensitive to lateral torsional buckling. Glass beams fail under a critical buckling load at stresses that lie far below the theoretical simple bending strength, due to the complex combination of torsion and out-of-plane bending, which characterises the instability phenomenon. The critical load can be increased considerably by preventing the upper rim from moving out of the beam's plane. Different boundary conditions are examined for different loading types. The load carrying capacity of glass beams can be increased three times and more using relatively simple, cheap lateral restraints.

• Geomechanics and Engineering
• /
• 제5권1호
• /
• pp.71-86
• /
• 2013

For rock materials, a transversely isotropic failure criterion established through the extended Lade-Duncan failure criterion incorporating an anisotropic state scalar parameter, which is a joint invariant of deviatoric microstructure fabric tensor and normalized deviatoric stress tensor, is verified with the results of triaxial compressive data on Tournemire shale. For torsional shear mode with $0{\leq}b{\leq}0.75$, rock shear strengths decrease with ${\alpha}$ increasing until the rock shear strength approaches minimum value at ${\alpha}{\approx}40^{\circ}$, and after this point, the rock shear strengths increase as ${\alpha}$ increases further. For the torsional shear mode with b > 0.75, rock shear strengths are almost constant for ${\alpha}{\leq}40^{\circ}$, but it increases with increase in ${\alpha}$ afterwards. The rock shear strength variation against ${\alpha}$ agrees with shear strength changing tendency of heavily OCR natural London Clays tested before. Prediction results show that the transversely isotropic failure criterion proposed in the paper is reasonable.

• Structural Engineering and Mechanics
• /
• 제2권3호
• /
• pp.269-284
• /
• 1994

The analysis and tests of thin-walled channel frames including nonlinear flexible or semi-rigid connection behaviour is presented. The semi-rigid connection behaviour is modelled using a mathematical approximation of the connection flexibility-moment relationship. Local instability such as local buckling and torsional flexural buckling of the member are included in the analysis. The full response of the frame, up to the collapse load, can be predicted. Experimental investigation was carried out on a series of simple double storey symmetrical frames with the purpose of verifying the accuracy and validity of the analysis. Agreement between the theoretical and experimental results is acceptable. The investigation also shows that connection flexibility and local instability such as local buckling and torsional flexural buckling can affect the behaviour and strength of thin-walled frames significantly. The results can also provide further insight into the advanced study of practical structures where interaction between flexible connections and phenomenon associated with thin-walled members are present.

• Structural Engineering and Mechanics
• /
• 제10권2호
• /
• pp.165-180
• /
• 2000

An analytical model with tension softening for the prediction of the capacity of prestressed concrete beams under pure torsion and under torsion combined with shear and flexure is introduced. The proposed approach employs bilinear stress-strain relationship with post cracking tension softening branch for the concrete in tension and special failure criteria for biaxial stress states. Further, for the solution of the governing equations a special numerical scheme is adopted which can be applied to elements with practically any cross-section since it utilizes a numerical mapping. The proposed method is mainly applied to plain prestressed concrete elements, but is also applicable to prestressed concrete beams with light transverse reinforcement. The aim of the present work is twofold; first, the validation of the approach by comparison between experimental results and analytical predictions and second, a parametrical study of the influence of concentric and eccentric prestressing on the torsional capacity of concrete elements and the interaction between torsion and shear for various levels of prestressing. The results of this investigation presented in the form of interaction curves, are compared to experimental results and code provisions.

• 한국컴퓨터정보학회:학술대회논문집
• /
• 한국컴퓨터정보학회 2021년도 제64차 하계학술대회논문집 29권2호
• /
• pp.105-106
• /
• 2021

자동사격통제기능 및 탄의 자동장전기능을 가진 최신 무기체계의 동력장치는 엔진, 변속기 및 냉각장치로 구성되어 있다. 이러한 동력장치를 정비하기 위해서는 엔진과 변속기를 결합 및 분리할 수 있는 특수공구의 사용이 필수적이다. 하지만, 기존 제품은 사용 특성에 따라 비틀림이 심하여 쉽게 마모되는 현상을 가진다. 본 연구에서는 강도저하로 인한 잦은 파손현상과 엔진 우측 연결부 조임 시 간접 현상에 자유로운 공구를 제안하고자 한다. 구조해석 프로그램(ABAQUS)을 통한 비틀림 강도 해석과 이를 바탕으로 최적 설계를 진행하여 제작된 공구는 기존 문제점을 해결하고 공인인증기관에서 토크의 130%의 비틀림 실험에서 문제없음을 확인하였다. 본 연구의 결과물은 동력장치 정비를 위한 특수공구의 국산화로 인한 경제적 측면에서 큰 도움이 될 것으로 사료된다.