• 한국자동차공학회논문집
• /
• 제18권4호
• /
• pp.1-7
• /
• 2010

Large quantity of bending deformation as well as irregular rotating torque fluctuation are the main struggles of the balance shaft module during a high speed rotation. Since two issues are much sensitive to the location of both supporting bearing and unbalance mass at a balance shaft, it is recommended to construct a design strategy on balance shaft at the early stage so as to save developing time and effort before approaches to the detailed design process. In this paper, an optimal design formulation is proposed to minimize the elastic strain energy due to bending as well as the kinematic energy of polar moment of inertia in rotation. Case studies of optimal design are conducted for different mass ratio as well as linear combination of objective function and its consequence reveals that global optimum of balance shaft model is existed over possible design conditions. Simulation shows that best locations of both supporting bearing and unbalance are globally 20% and 80%, respectively, over total length of a balance shaft.

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권4호
• /
• pp.26-30
• /
• 2014

We investigate the upper critical field anisotropy ${\Gamma}_H$ and the magnetic penetration depth anisotropy ${\Gamma}_{\lambda}$ of a high-quality $FeSe_{1-x}$ single crystal using angular dependent resistivity and torque magnetometry up to 14 T. High quality single crystals of $FeSe_{1-x}$ were successfully grown using $KCl-AlCl_3$ flux method, which shows a sharp superconducting transition at $T_C{\sim}9K$ and a high residual resistivity ratio of ~ 25. We found that the anisotropy ${\Gamma}_H$ near $T_C$ is a factor of two larger than found in the poor-quality crystals, indicating anisotropic 3D superconductivity of $FeSe_{1-x}$. Similar to the 1111-type Fe pnictides, the anisotropies ${\Gamma}_{\lambda}$ and ${\Gamma}_H$ show distinct temperature dependence; ${\Gamma}_H$ decreases but ${\Gamma}_{\lambda}$ increases with lowering temperature. These behaviors can be attributed to multi-band superconductivity, but different from the case of $MgB_2$. Our findings suggest that the opposite temperature dependence of ${\Gamma}_{\lambda}$ and ${\Gamma}_H$ is the common properties of Fe-based superconductors.

• 한국CDE학회논문집
• /
• 제19권4호
• /
• pp.332-339
• /
• 2014

This paper presents on the development of wheel-terrain interaction device using low-priced sensors, which will be used to predict the drawbar pull and optimal slip of off-road vehicle in real time. The essential variables obtained in the device to predict the mobility of vehicles are determined based on semi-empirical model describing the wheel-terrain interaction. Using the developed device, the experiments about the wheel-terrain interaction were performed on the soil of the Jumunjin standard sand, which yielded dynamic weight, motor driving torque, drawbar pull, and sinkage with respect to wheel slip ratio. Finally, the repeatability of the measured data are verified through repeating the experiments three times on the same condition.

• 천문학회보
• /
• 제37권2호
• /
• pp.73.1-73.1
• /
• 2012

We use hydrodynamic simulations to study the physical properties of gaseous structures in barred galaxies and their relationships with the bar strength. We vary the bar mass fbar relative to the spheroidal component as well as its aspect ratio. We derive expressions for the bar strength Qb and the radius where the maximum bar torque occurs. When applied to observations, these expressions suggest that bars in real galaxies are most likely to have fbar = 0.25-0.5. Dust lanes approximately follow one of x1-orbits and tend to be more straight under a stronger and more elongated bar. A nuclear ring of a conventional x2 type forms only when the bar is not so massive or elongated. The radius of an x2-type ring is generally smaller than the inner Lindblad resonance, decreases systematically with increasing Qb, evidencing that the ring position is not determined by the resonance but by the bar strength. Nuclear spirals exist only when the ring is of the x2-type and sufficiently large in size. Unlike the other features, nuclear spirals are transient in that they start out as being tightly-wound and weak, and then due to the nonlinear effect unwind and become stronger until turning into shocks, with an unwinding rate higher for larger Qb.

• 한국수소및신에너지학회논문집
• /
• 제27권1호
• /
• pp.106-113
• /
• 2016

Lean burn engine, classified into port injection and direct injection, is recognized as a promising way to meet better fuel economy. Especially, LPG direct injection engine is becoming increasingly popular due to their potential for improved fuel economy and emissions. Also, LPDi engine has the advantages of higher power output, higher thermal efficiency, higher EGR tolerance due to the operation characteristics of increased volumetric efficiency, compression ratio and ultra-lean combustion scheme. However, LPDi engine has many difficulties to be solved, such as complexity of injection control mode (fuel injection timing, injection rate), fuel injection pressure, spark timing, unburned hydrocarbon and restricted power. This study is investigated to the influence of spark timing, fuel injection position and fuel injection rate on the combustion stability of LPDi engine. Piston shape is constituted the bowl type piston. The characteristics of combustion is analyzed with the variations of spark timing, fuel injection position and fuel injection rate (early injection, late injection) in a LPDi engine.

• Journal of Biosystems Engineering
• /
• 제25권5호
• /
• pp.351-358
• /
• 2000

This study was conducted to develop a speed control system of a DC motor which drove a barley seeder mounted on a combine harvester. Barley seeder mounted on a combine has been known to reduce labor and cost of barley cultivation. However, development of the seeder has been unsuccessful because the combine, a dedicated rice and barley harvester has not enough space and proper power take-off for barley seeder. To develop a barley seeder, small powered motor speed controller was required. A proximity sensor for detecting working speed of the combine and a programmable one board microprocessor was used to develope a control system. Motor parameters and motor constant, relationship between seeding rate, motor speed, groove volumes of a tested roller, torque were measured. The proximity sensor sent a frequency signal to the microprocessor. In laboratory experiments, the excitation voltage of the motor was shown not to be proportional to the size of pulse width (duty ratio). A table transforming frequency signal, that represented for working speed to proper pulse width was developed from seeding rate experiments. However, seeding rate at low frequency signal was not proportional to the working speed. Seeding rate control proportional to the frequency signal was achieved by shifting of the frequency signal.

• 한국정밀공학회지
• /
• 제29권7호
• /
• pp.723-729
• /
• 2012

Spring-like leg models have been employed to explain various dynamic characteristics in human walking. However, this leg stiffness model has limitations to represent complex motion of actual human gait, especially the behaviors of each lower limb joint. The purpose of this research was to determine changes of total leg stiffness and lower limb joint stiffness with gait speed in knee osteoarthritis. Joint stiffness defined as the ratio of the joint torque change to the angular displacement change. Eight subjects with knee osteoarthritis participated to this study. The subject walked on a 12 m long and 1 m wide walkway with three sets of four different randomly ordered gait speeds, ranging from their self-selected speed to maximum speed. Kinetic and kinematic data were measured using three force plates and an optical marker system, respectively. Joint torques of lower limb joints calculated by a multi-segment inverse dynamics model. Total leg and each lower limb joint had constant stiffness during single support phase. The leg and hip joint stiffness increased with gait speed. The correlation between knee joint angles and torques had significant changed by the degree of severity of knee osteoarthritis.

• 수산해양기술연구
• /
• 제57권3호
• /
• pp.256-263
• /
• 2021

In this study, blending oils of diesel oil and butanol were used as fuel oil for diesel engine to measure combustion pressure, fuel consumption, air ratio and exhaust gas emission due to various operating conditions such as engine revolution and torque. Using these data, the results of analyzing the engine performance, combustion characteristics and exhaust emission characteristics such as NOx (nitrogen oxides), CO₂ (carbon dioxide), CO (carbon monoxide) and soot were as follows. The fuel conversion efficiency at each load was highest when driven in the engine revolution determined by a fixed pitch propeller law. Except 30% butanol blending oil, fuel conversion efficiency of the other fuel oils increased as the load increased. Compared to diesel oil, using 10% and 20% butanol blending oil as fuel oil was advantageous in terms of thermal efficiency, but it did not have a significant impact on the reduction of exhaust gas emissions. On the other hand, future research is needed on the results of the 20% butanol blending oil showing lower or similar levels of smoke concentration and carbon monoxide emission rate other than those types of diesel oil.

• Steel and Composite Structures
• /
• 제39권4호
• /
• pp.419-433
• /
• 2021

In composite structures, shear connectors are crucial components to resist the relative slip between the steel and concrete, and thereby to achieve the composite actions. In the service stage, composite structures are usually in elastic state, so the elastic stiffness of the shear connection is a quite important parameter in the structural analysis of composite structures. Nevertheless, the existing studies mainly focus on the load-slip relationship rather than the tangent stiffness at the initial elastic stage. Furthermore, when composite beams subjected to torque or local load, shear connections are affected by both tensile force and shear force. However, the stiffness of shear connections under combined effects appears not to have been discussed hitherto. This paper investigates the initial elastic stiffness of stud connections under combined effects of biaxial forces. The initial expression and the relevant parameters are obtained by establishing a simplified analytical model of the stud connection. Afterwards, parametric finite element analysis is performed to investigate the effects of the relevant factors, including the stud length, stud diameter, elastic modulus of concrete, elastic modulus of steel and volume ratio of reinforcement. The feasibility of the proposed modelling has been proved by comparing with sufficient experimental tests. Based on the analytical analysis and the extensive numerical simulations, design equations for predicting the initial elastic stiffness of stud connections are proposed. The comparison between the equations and the data of finite element models demonstrates that the equations are accurate enough to serve for engineering communities.

• 한국기계가공학회지
• /
• 제21권9호
• /
• pp.21-27
• /
• 2022

The rotorcraft engine gearbox transmits the power generated by the turboshaft engine to the rotor by reducing the rotational speed and increasing the torque. The core of the rotorcraft engine gearbox is lightweight performance, which requires maximum weight reduction within the range that meets various requirements and constraints. Therefore, lightweight design through gear macro geometry optimization is necessary. In this study, gear macro geometry optimization was performed to reduce the weight of a rotorcraft engine gearbox. NSGA-III was used for the optimization, resulting in a combination of the gear ratio and macro geometry that minimizes the weight of the total gear. In addition, the safety factor of the gears satisfied the given conditions.