• 한국방재학회 논문집
• /
• 제8권2호
• /
• pp.97-103
• /
• 2008

Determination of stress-strain relationship in torsional tests is complicated due to nonuniform stress-strain variation occurring linearly with the radius in a soil specimen in torsion. The equivalent radius approach is adequate when calculating strain at low to intermediate strains, however, the approach is less accurate when performing the test at higher strain levels. The modified equivalent radius approach was developed to account for the problem more precisely. This approach was extended to generate the plots of equivalent radius ratio versus strain using modified hyperbolic and Ramberg-Osgood models. Results showed the effects of soil nonlinearity on the equivalent radius ratio curves were observed. Curve fitting was also performed to find the stress-strain relationship by fitting the theoretical torque-rotation relationship to measured torque-rotation relationship.

• Journal of Biosystems Engineering
• /
• 제8권1호
• /
• pp.38-46
• /
• 1983

This study was carried out to investigate the possibility of improving the performance of a kerosene engine with water addition. The engine used in this study was a single-cylinder, four-cycle kerosene engine with the compression ratio of 4.5. Water could be successfully added into the inlet manifold by an extra carburetor for the volumetric ratios of 5, 10, 20, and 30 percents. Variable speed tests at wide-open throttle were performed for five speed levels in the range of 1,000 to 2,200rpm for each fuel type. Volumetric efficiency and brake specific fuel consumption were determined, and brake thermal efficiency based on the lower heats of combustion of kerosene was calculated. To examine variation in fuel consumption, CO concentration, and cooling water temperature, part load tests were also performed. The results obtained are summarized as follow. (1) Brake torque increased almost in proportion to volumetric efficiency. But the ratio of increase in torque was greater than that of volumetric efficiency. Mean torque over the speed range of 1,000 to 2,200rpm increased 1, 3, 7, and 2 percents for 5, 10, 20, and 30 percents water addition, respectively. The increase in brake torque with water addition was greater at lower speeds. (2) Mean brake specific fuel consumption over the speed range of 1,000 to 2,200rpm decreased 1, 2, 3, and 3 percents for 5, 10, 20, and 30 percents water addition, respectively. (3) Mean temperature of cooling water over the speed range of 1,000 to 2,200rpm decreased 2, 4, 8, and 12 percents for 5, 10, 20, and 30 percents water addition, respectively. (4) The effects of decreasing CO concentration in the exhaust emissions with water addition were significant. At the speed range of 1,000 to 2,200rpm, CO concentration in the exhaust emissions decreased 2, 10, 23, percents for 5, 10, and 20 percents water addition, respectively. (5) Deposits were not discovered in the combustion chamber during the experiment. However, a little rust was formed in the water-supply carburetor.

• 한국콘텐츠학회논문지
• /
• 제6권12호
• /
• pp.226-234
• /
• 2006

본 연구는 테이핑 요법이 슬관절의 등속성 기능 및 통증에 미치는 영향을 알아보기 위하여 슬관절 부위에 통증을 호소하는 $65{\sim}70$세 여성 노인 12명을 대상으로 슬건근, 대퇴사두근, 슬개골 부위에 폭 5cm의 테이프를 8주 동안 주당 3회씩 총 24회를 적용시킨 후 등속성 근 기능인 최대근력, 상대근력, 근 지구력(총 운동량), 근 지구력(운동피로도), 동측 근력 비율, 주관적 통증정도인 시각적 상사 척도와 구술적 평정 척도의 변화를 분석한 결과 다음과 같은 결론을 얻었다. 즉, 8주간의 테이핑 요법 후 최대근력, 상대근력, 근지구력(총 운동량), 동측근력비율은 각각 유의하게 증가하였고 (p<.05; p<.01), 근지구력(운동피로도) 및 시각적 상사 척도와 구술적 평정 척도 점수가 각각 유의하게 감소하였다(p<.05).

• 오토저널
• /
• 제11권4호
• /
• pp.3-12
• /
• 1989

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권3호
• /
• pp.104-109
• /
• 1999

In order to design and predict the performance of the harmonic side drive motor, it is necessary to analyze the torque generated by the structure. In this paper, an analytical model is proposed for design. Conformal mapping is used to model the capacitance and torque of the motor as a function of the rotor angular position with two-dimensional approximation. Then the result of conformal mapping analysis is verified with F.E.M result.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권3호
• /
• pp.135-142
• /
• 2004

In this paper, the magnetic circuit characteristics and the current/torque analysis of a Spoke Type permanent magnet motor have been researched, compared with the SPM Type motor. In the magnetic circuit analysis, the characteristic of air-gap flux density has been analyzed according to the variation of the number of pole and the ratio of magnet height to arc length using finite element method and circuit equations. Moreover, the electromagnetic and the reluctance torque have been analyzed by the current profile, which is obtained from the variation of turn-on angle, and these informative data has been utilized for the overall characteristics of the Spoke Type BLDC motor.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(1)
• /
• pp.243-246
• /
• 2003

This paper presents a new motor design well suited for an advanced exercise bike. The advanced exercise bike setup high demands for performance and physical dimensions, which is high torque, wide speed range and a diameter/length ratio around 5. These requirements makes the new motor design called an E-core Transverse Flu Machine (ETFM) vev interesting because the segmented design of the stator and rotor poles enables high diameter without increasing the flux-path and since the ETFM is similar to the switched reluctance motor, high torque and wide speed range is possible. The design of the ETFM can be peformed using a developed design program, which is also introduced in the paper. A prototype of the exercise bike with the ETFM and a classical H-bridge converter with analog current control is constructed for verification of the concept.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.417-420
• /
• 2000

In order to the torque control the indirect flux control was performed by controlling the ratio of e/f and the q-axis flux was estimated by the slip command and q-axis flux was estimated by the slip command and q-axis current in the rotor circuits. Also the frequency was controlled to keep on the q-axis flux to be zero and the constant torque characteristics could be obtained by generation the preset torque. In the induction motor driven by the boltage source inverter with the constant voltage and frequency the speed variation is expressed as a slip So the speed control can be achieved by slip compensation The slip was calculated with a q-flux current filtered by first-order filter and as the result the error problem which may occur in current detection was eliminated

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.123-125
• /
• 2004

This paper presents the application of response surface methodology (RSM) to design optimization for two types of synchronous reluctance motors (SynRMs); one has 12 slots with distributed winding, and the other has 6 slots with concentrated winding, to improve the ratio between torque ripple and average torque. The usefulness of RSM in optimization problem of SynRM is verified as compared with the results of finite element analysis. In the end, the optimized two SynRMs are compared with SynRM currently used in air-conditioning compressor in connection with torque performance and loss.

• 오토저널
• /
• 제14권3호
• /
• pp.109-114
• /
• 1992

The purpose of this study is to experimentally research the effects of polymer additives on turbulent transition of Couette flow between concentric cylinders when outer one is rotating and inner one is at rest; the diameter ratio being 0.2. Aqueous polymer solution generate the degradation phenomena in machine forming work, but this is not effected in about 10 minute at 5ppm. aqueous polymer solution testing. The Reynolds number, referred to the gap distance and rotation velocity of the outer cylinder, of turbulent transition is about 20000 for water flow. In the laminer region, the torque value is as same as theoretical one in the region of low Reynolds number, but becomes high with an increase in the Reynolds number. The polymer additives reduce the Reynolds number for turbulent transtition. In the turbulent region, the torque is remarkably reduced by the polymer additives, soluble polymer take down effect of turbulent transition boundary torque.