• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권1호
• /
• pp.58-69
• /
• 2016

This paper describes the design and implementation of a new diode clamped multilevel inverter for variable frequency drive. The diode clamp multilevel inverter has been widely used for low power, high voltage applications due to its superior performance. However, it has some limitations such as increased number of switching devices and complex PWM control. In this paper, a new topology is proposed. New topology requires only (N-1) switching devices and (N-3) clamping diodes compared to existing topology. A modified APO-PWM control method is used to generate gate pulses for inverter. The proposed inverter topology is coupled with single phase induction motor and its performance is tested by MATLAB simulation. Finally, a prototype model has built and its performance is tested with single phase variable frequency drive.

• 한국통신학회논문지
• /
• 제34권3B호
• /
• pp.225-234
• /
• 2009

Recently IPTV service is penetrating to the ordinary home users very swiftly. One of the first phase of IPTV service is considered to be VoD, and a nationwide availability of the VoD service imposes tremendous pressure to the network resource due to its requirements for the broad bandwidth, the inherent nature of unicast technology, and the large scalability, etc. This work suggests a novel and practical method to the design of network resource for the VoD service. Especially, we explore the distributed content storage problem that takes into account the popularity of the video contents and its corresponding link dimensioning problem that takes into account the grade of service for the flow level quality of service about the VoD service. By assuming a realistic topology for the nationwide IP backbone network of Korea, which is a typical tree topology, we suggest an analytic method for the design of VoD service.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.651-652
• /
• 2008

This research presents a multi-objective optimal design employing topological approach to maximize magnetic energy while minimizing structural deformation which is caused by magnetic reluctance force and magnetostriction. A design sensitivity formula is derived by employing the adjoint variable method (AVM) to avoid numerous sensitivity evaluations for a coupled magneto-mechanical analysis. The sensitivity analysis is verified using the finite difference method (FDM) in a C-shape actuator. A linear actuator used in a home appliance is examined for optimal design and demonstrates the strength of the proposed topology optimization approach.

• 한국전산구조공학회논문집
• /
• 제26권4호
• /
• pp.241-246
• /
• 2013

본 논문에서는 밀도법 기반 위상 최적설계를 통해 얻어진 수치 결과를 바탕으로 CAD 모델을 구성하고 이를 3차원 프린터로 제작하여 실험적으로 최적설계를 검증하였다. 위상 최적설계 과정에서는 체커보드(Checkerboard) 현상이나 잔가지가 종종 나타나는데, 이는 최적설계 구조물을 실제로 제작함에 있어서 어려움을 준다. 이러한 문제점을 해결하기 위하여 민감도 필터링과 모폴로지 기법을 사용하였다. 엄밀한 검증을 위하여 수치 모델과 실험 모델의 부피율을 일치시켰다. 위상 최적설계를 포함한 다양한 설계에 대하여 실험을 통해 비교하여 최적설계 구조물이 가장 높은 강성을 가지고 있음을 확인하였으며 컴플라이언스에 대한 실험결과는 수치해석 값과 잘 일치함을 확인하였다.

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.113-119
• /
• 2012

Ultrasonic bonding is the novel packaging method for flip-chip with high yield and low-temperature bonding. The bonding module is a core part of the bonding machine, which can transfer the ultrasonic energy into the bonding spot. In this paper, we propose topology optimization technique which can make new design of boding modules due to the constraints on resonance frequency and mode shapes. The designed bonding module using topology optimization was fabricated in order to evaluate the bonding performance and reliable operation during the continuous bonding process. The actual production models based on the proposed design satisfied the target frequency range and ultrasonic power. The bonding test was performed using flip-chip with lead-free Sn-based bumps, the results confirmed that the bonding strength was sufficient with the designed bonding modules. Also the performance degradation of the bonding module was not observed after the 300-hour continuous process with bonding conditions.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권6호
• /
• pp.832-841
• /
• 2016

The voltage-frequency island (VFI) design paradigm has strong potential for achieving high energy efficiency in communication centric manycore system-on-chip (SoC) design called network-on-chip (NoC). However, because of the diminished scaling of wire-dimension and supply voltage as well as threshold voltage in modern CMOS technology, the vulnerability to link failure in VFI NoC is becoming a crucial challenge. In this paper, we propose an energy-optimized topology generation technique for VFI NoC to cope with permanent link failures. Based on the energy consumption model, we exploit the on-chip communication traffic patterns and characteristics of link failures in the early design stage to accommodate diverse applications and architectures. Experimental results using a number of multimedia application benchmarks show the effectiveness of the proposed three-step custom topology generation method in terms of energy consumption and latency without any degradation in the fault coverage metric.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.376.2-376
• /
• 2002

In this study, the shape of suspension load beam for NFR(Near Field Recording) was proposed, which was designed using Topology optimization based on Homogenization method. Lens and Micro-mirror are attached to the end of the suspension load beam for collection and control the light, which increasing the system mass. Increment of the system mass cause to decrease the tracking stiffness mode frequency. (omitted)

• 전력전자학회논문지
• /
• 제12권6호
• /
• pp.510-516
• /
• 2007

본 논문에서는 더 높은 에너지 효율을 요구하는 전자 기기들의 사용에 따른 고전력 밀도 AC/DC adapter를 위한 향상된 제어 방법을 제안한다. PFC (Power Factor Correction) 토폴로지는 BCM (Boundary Conduction Mode)제어 방식을 적용한 부스트 토폴로지를 기본으로 하였으며, DC/DC 토폴로지는 50% 고정 duty법과 함께 새롭게 제안된 Off-time 제어법을 적용한 하프브릿지 토폴로지를 기본으로 하였다. 이는 반도체 소자와 마그네틱 소자의 크기를 줄이는데 용이하다. 85W급 AC/DC 어뎁터(18.5V/4.6A)를 설계하여 실험한 결과 90%의 효율과 $36W/in^3$의 전력밀도가 측정되었고 무부하시 전력 손실은 0.5W를 달성하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.728-733
• /
• 2008

Though multi-panel structures lined with a poroelastic material have been widely used to reduce sound transmission in various fields, most of the previous works to design them were conducted by repeated analyses or experiments based on initially given configurations or sequences. Therefore, it was difficult to obtain the optimal sequence of multi-panel structures lined with a poroelastic material yielding superior sound isolation capability. In this work, we propose a new design method to sequence a multi-panel structure lined with a poroelastic material having maximized sound transmission loss. Being formulated as a one-dimensional topology optimization problem for a given target frequency, the optimal sequencing of panel-poroelastic layers is systematically carried out in an iterative manner. In this method, a panel layer is expressed as a limiting case of a poroelastic layer to facilitate the optimization process. This means that main material properties of a poroelastic material are treated as Interpolated functions of design variables. The designed sequences of panel-poroelastic layers were shown to be significantly affected by the target frequencies; more panel layers were used at higher target frequencies. The sound transmission loss of the system was calculated by the transfer matrix derived from Biot's theory.

• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.177-185
• /
• 2015

This paper describes a weight-reduction design method for the car bodies of a double deck high-speed train (service speed of 300 km/h). The method uses lightweight materials and a topology optimization technique. In this study, aluminum extrusions and sandwich composites were selected as the best materials to reduce the weight of the car body. The topology optimization technique was used to determine which car body parts could be made of the sandwich composites to achieve additional weight savings. The results of the topology optimization analysis showed that sandwich composites could be used for secondary car body members such as the roof and the second underframe. Also, it was found that a car body composed of aluminum extruded parts and sandwich composites could weigh up to 14% less than a car body made of only aluminum extrusions.