• The korean journal of orthodontics
• /
• v.48 no.6
• /
• pp.384-394
• /
• 2018

Objective: This study was performed to investigate an appropriate degree of prestretch for orthodontic synthetic elastomeric chains focusing on time-dependent viscoelastic properties. Methods: Orthodontic synthetic elastomeric chains of two brands were prestretched to 50, 100, 150, and 200% of the original length in one and three cycles, and the hysteresis areas of the obtained stress-strain curves were determined. Acrylic plates were employed to maintain constant strain during the experiment. A total of 180 samples were classified into nine groups according to brand, and their stresses and permanent deformations were measured immediately after prestretch (0 hour), after 1 hour and 24 hours, and after 1, 2, 3, 4, 5, 6, 7, and 8 weeks. The relationship between stress relaxation and permanent deformation was investigated for various degrees of prestretch, and the estimated stress resulting from tooth movement was calculated. Results: The degree of prestretch and the stress relaxation ratio exhibited a strong negative correlation, whereas no correlation was found between the degree of prestretch and the average normalized permanent strain. The maximal estimated stress was observed when prestretch was performed in three cycles to 200% of the original length. Conclusions: Although prestretch benefited residual stress, it did not exhibit negative effects such as permanent deformation. The maximal estimated stress was observed at the maximal prestretch, but the difference between prestretch and control groups decreased with time. In general, higher residual stresses were observed for product B than for product A, but this difference was not clinically significant.

• The Journal of Korean Academy of Prosthodontics
• /
• v.17 no.1
• /
• pp.35-46
• /
• 1979

A number of experimental studies have been carried out in order to clarify the question as to how temporomandibular joint adapt to the changes of mandibular movement and occlusal equilibration. Recently, the studies on the interrelations between anatomical structure of temporomandibular joint and the state of occlusion have been actively performed in dentistry particularly in prosthodontic field. Author performed extraction of unilateral mandibular molars in 30 mature male rats, and observed histological changes of temporomandibular joint through the light microscope. Following results were obtained. 1. The loss of unilateral teeth gave rise to the changes in the location of condylar head, that is, interior displacement of condylar head in the extraction side and upper displacement in the non-extraction side. 2. Articular disk was compressed by the interior surface of condylar head, resulting in its extension below the condylar neck in the extraction side, and the histological arrangement of the compressed area showed irregular feature. 3. The extension of articular disk below the condylar neck was accompanied with the contraction of muscle fibers which were originated from the articular disk. 4. The cartilage layer of articular fossa to the exterior of the extraction side showed hypertropy. 5. Early in the experiment, the inernal extremity of condylar head of extract ion side showed bone resorption, and cartilage layer of condylar head showed hypertropy. At 12 weeks after experiment, the condylar surface showed flattened, and the cartilage layer of condylar head was replaced by the compact bone. 6. The articular disk showed the formation of pannus in the extraction side as well as in the non-extraction side. 7. The occlusal disturbance due to unilateral missing teeth has brought about the non-inflammatory retrogressive change and osteoarthrotic change late in the experiment.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.32 no.6
• /
• pp.563-566
• /
• 2010

Retrobulbar abscess is a rare, but severe complication of paranasal sinusitis. The clinical presentations are eyelid swelling, erythema, proptosis, conjunctival chemosis, restricted ocular movement, and decreased visual acuity. Diagnostic methods available for evaluating retrobulbar abscess include sinus X-ray, ultrasonography, computed tomography (CT), and bacterial culture. For the treatment of retrobulbar abscess, immediate surgical drainage and systemic antibiotic therapy are needed. Proper diagnosis and treatments are necessary for preventing visual loss, cavernous sinus thrombosis, subdural abscess, and other lifethreatening complications. A patient, a 30-year-old man, was admitted to our hospital because of progressive eyelid swelling, erythema, ptosis and decreased visual acuity on the right eye after endodontic treatment. The sinusitis occurred secondary to the infection from an upper molar tooth. The spread of the infection led to the orbit via ethmoidal sinus and posterior orbital wall. Immediate surgical intervention was performed and systemic antibiotics was administrated. The symptoms and signs are improved after treatments, so we present our case with a brief review of the literature.

• The korean journal of orthodontics
• /
• v.22 no.4 s.39
• /
• pp.823-836
• /
• 1992

Guiding a tooth along an arch wire results in a counteracting frictional force among arch wires, bracket and ligature. This frictional forces should be eliminated or minimized when orthodontic teeth movement is being planned. The purpose of this study was to evaluate the changes of width, cross-sectional forms and surface morphologies of stainless steel wire and $Elgiloy^{\circledR}$ wire after electropolising. Experimental variables included in this experiment were arch wire materials, current, electrolyte temperature and polishing time. Wire widths were measured by micrometer and cross-sectional forms and surface morphologies were examined with optical microscope and scanning electron microcope. The results were as follows: 1. The mean and standard deviation of widths of stainless steel wire and $Elgiloy^{\circledR}$ wire varying polishing time with condition of $249A/dm^2$ and $20^{\circ}C,\;249A/dm^2$ and, $332A/dm^2$ and $20^{\circ}C$ and $332A/dm^2$ and $250^{\circ}C$ were obtained. 2. With increasing polishing time, the widths of stainless steel wire and $Elgiloy^{\circledR}$ wire became decreased proportionally 3. The changes of widths of stainless steel wire and $Elgiloy^{\circledR}$ wire were statistically insignificant between $20^{\circ}C$ group and $25^{\circ}C$ group, but significant between $249A/dm^2$ group and $332A/dm^2$ group. 4 The cross-sectional forms of wire after electropolishing were not changed in stainless steel wire, and while it were changed to rounded corners in $Elgiloy^{\circledR}$ wire. 5. The surface morphologies of wire after electropolishing were scratch-absent and more smoothened both in stainless steel wire and $Elgiloy^{\circledR}$ wire.

• The korean journal of orthodontics
• /
• v.44 no.5
• /
• pp.236-245
• /
• 2014

Objective: To evaluate the therapeutic effects of a preformed assembly of nickel-titanium (NiTi) and stainless steel (SS) archwires (preformed C-wire) combined with temporary skeletal anchorage devices (TSADs) as the sole source of anchorage and to compare these effects with those of a SS version of C-wire (conventional C-wire) for en-masse retraction. Methods: Thirty-one adult female patients with skeletal Class I or II dentoalveolar protrusion, mild-to-moderate anterior crowding (3.0-6.0 mm), and stable Class I posterior occlusion were divided into conventional (n = 15) and preformed (n = 16) C-wire groups. All subjects underwent first premolar extractions and en-masse retraction with preadjusted edgewise anterior brackets, the assigned C-wire, and maxillary C-tubes or C-implants; bonded mesh-tube appliances were used in the mandibular dentition. Differences in pretreatment and post-retraction measurements of skeletal, dental, and soft-tissue cephalometric variables were statistically analyzed. Results: Both groups showed full retraction of the maxillary anterior teeth by controlled tipping and space closure without altered posterior occlusion. However, the preformed C-wire group had a shorter retraction period (by 3.2 months). Furthermore, the maxillary molars in this group showed no significant mesialization, mesial tipping, or extrusion; some mesialization and mesial tipping occurred in the conventional C-wire group. Conclusions: Preformed C-wires combined with maxillary TSADs enable simultaneous leveling and space closure from the beginning of the treatment without maxillary posterior bonding. This allows for faster treatment of dentoalveolar protrusion without unwanted side effects, when compared with conventional C-wire, evidencing its clinical expediency.

• The Journal of Korean Academy of Prosthodontics
• /
• v.22 no.1
• /
• pp.72-78
• /
• 1984

The notion that the axis of the shaft of the articulator must coincide the patient's mandibular transverse axis tells us the importance of locating the axis precisely. When using kinematic axis to transfer a cast to an articulator, the anatomic asymmetry of the contralateral points will result in certain distortion when the axis transferred to an articulator where the mechanical axis produces symmetry. In this study, after locating the true hinge axis point with Denar hinge axis locator, the discrepancies between true hinge axis point and arbitrary hinge axis point that was 13mm anterior from the posterior margin of center of trangus to the outer canthus of eye were measured. And the discrepancies between left and right true hinge axis point in the superoinferior and anteroposterior directions were measured. For this study, 20 dental students who have no missing teeth and no difficulties of mandibular movement were selected. Upper and lower cast of subjects were mounted on Denar Mark II articulator uisng Denar Slidematic face-bow and centric relation record for the measurement of discrepancies between left and right true hinge axis points. The results obtained as follows. 1. The mean distance from the arbitrary hinge axis point to the true hinge axis point was as follows. Right: horizontal distance; 1.99mm, vertical distance; 2.12mm, linear distance; 3.36 mm. Left: horizontal distance; 1.39mm, vertical distance; 2.06mm, linear distance; 2.09mm. Total: horizontal distance; 1.69mm, vertical distance; 2.09mm linear distance; 3.06 mm. 2. The 87.5% of true hinge axis points were within 5mm of the arbitrary hinge axis point. 3. The mean discrepancies between the right and left hinge axis point were 2.92mm in superoinferior direction and 4.74mm in anteroposterior direction. 4. When transferring the axis to the articulator, anatomic asymmetry between right: and left axis point produces in dislocation of cast on the articulator, and undesirable shift in esthetic tooth position will be resulted.

• The korean journal of orthodontics
• /
• v.21 no.1 s.33
• /
• pp.223-238
• /
• 1991

This study was carried out in order to findout the amount of tooth movement, the changes arch size and the changes in arch morphology following orthodontic treatment and to provide a guideline for to predict post-treatment arch morphology. The sample group for this study consists of 15 males and 22 females, totalling in 37 persons, who received orthodontic treatment at Orthodontic Department of Dankook Univ. Dental Hospital. They are classified into Extraction Class I treatment group (E I), Non-extraction Class I treatment group (N I), and Non-extraction Class III treatment group (N III), according to their pre-treatment malocclusion state and methods of treatment. Following conclusions and averaged dental arch form for each group were obtained by cephalometric linear measurements and dental arch measurements using pre- and post-treatment lateral cephalograms and plaster study models. 1. Intercanine width were reduced in max. of both EI and NI during the period of treatment, 2. Intermolar width were reduced in max. of EI and increased in max. of NI. Therefore although there was no difference between these two groups before the treatment, intermolar width of the max, of NI was wider than that of E1 after the treatment. 3. PMV-incisor distance and PMV-canine distance were decreased in both max. and mand. of EI and that of NI, during the period of treatment. PMV-molar distance was decreased in both max. and mand. of NI and in mand. of NIII. 4. Items that showed stability during the treatment were: max. & mand. PMV-molar distance, mand. intercanine and intermolar width in EI; mand. intercanine and intermolar width in NI; mand. & max. PMV-incisor distance, PMV-canine distance, max. PMV-molar distance and max. & mand. intercanine and intermolar width in NIII. 5. The differences in averaged canine and molar variances to post-treatment dental arch form were present only in EI and in NI. There was no variance between maxilla and mandible in each group.

• The korean journal of orthodontics
• /
• v.25 no.2 s.49
• /
• pp.201-208
• /
• 1995

Recently, magnetic forces are considered as a method for more efficient tooth movement. The purpose of this study was to evaluate the effects of the changes of the magnetic volume on the magnetic forces. The universal testing machine and the electronic balance were used for the exact measurement of the force with constant air gap. While the magnet was kept same on one side, the magnetic volume of the other side was increased gradually in four manners. In the first group, the thickness was increased by adding same size of the magnets one after another while the thickness was increased by changing with a thicker magnet gradually in the second group. In the third group. the width was increased by adding same size of the magnets while the width was increased by changing with a wider magnet gradually in the last group. The results were as follows : 1. With the increase of the thickness, the magnetic force increased, while the magnetic force decreased with the increase of the width. 2. The magnetic force according to the change of the magnetic volume showed the distribution of the logarithmic function. 3. An originally thick magnet showed larger force than the added magnets although both of them had same volume.

• Journal of Periodontal and Implant Science
• /
• v.34 no.2
• /
• pp.367-375
• /
• 2004

As the periodontal ligament cells show similar phenotype with osteoblasts, periodontal ligament cells are thought to play an important role in alveolar bone remodeling. According to recent studies, receptor activation of nuclear factor $^{\kappa}B$ ligand (RANKL) and osteoprotegerin (OPG) are expressed in periodontal ligament cells during tooth movement. Also periodontal ligament cells is known to play an important role in the progression of periodontal disease. This study was designed how the expression of RANKL and OPG in periodontal ligament cells was regulated by IL-1 ${\beta}in$ the concentration of $0.01{\sim}10$ ng/ml. The results are as follows; 1. Periodontal ligament cells which stimulated by 1L-1 ${\beta}$ increased soluble RANKL synthesis by dose-dependent pattern in the concentration of $0.01{\sim}10$ ng/ml. 2. 1L-1 ${\beta}$ induced mRANKL expression in dose-dependent manner in the concentration of $0.01{\sim}5$ ng/ml. 3. mOPG expression was not to be influenced by 1L-1 ${\beta}$. These results suggested that rat periodontal ligament cells could regulate osteoclastogenesis by stimulation of production of RANKL.

• Journal of Oral Medicine and Pain
• /
• v.20 no.1
• /
• pp.195-204
• /
• 1995

The purpose of this study was to evaluate effect of head posture change on initial occlusal contacts through measuring the distances between initial occlusal contacts and maximum intercuspal position at different head posture. Two special devices were designed and constructed. Mandibular movement replicator was used to assess reliability of the K6 diagnostic system(MKG; Myo-tronic Inc, Seatle, USA) and head posture calibrator was used to maintain the constant head posture during experiment. We measured difference of distance between initial occlusal contact and maximum intercuspal position with MKG in upright, supine, 45 degrees extension, 30 degrees flexion, 30 degrees right and left bending postion of the head. The Frankfurt horizontal plane was used as a reference plane. 21 adults aged from 23 to 25 were selected, who have normal or class I molar relationship, and have no symptoms on TMJ and masticatory muscles, and have restorations less than 3 surfaces on each tooth, and have no other prosthetic restoration. The obtained results were as follows : The mean absolute distances between initial occlusal contact and maximum intercuspal postion were 0.39(0.18mm in the upright position, 0.65(0.37mm in the supine position, 0.59(0.33mm in the 45 degree extension, 0.70(0.53mm in the 30 degrees flexion, 1.12(1.10mm in the 30 degrees right bending and 1.94(0.67mm in the 30 degrees left bending of the head. The positions of the initial occlusal contacts have a tendency to locate anterior, left and inferior to maximal intercuspal position in upright position, posterior and inferior in supine position and 45 degrees extension, anterior and inferior in 30 degrees flexion, right and inferior in 30 degrees right bending, and left and inferior in 30 degrees left bending of the head. There were significant differences among the initial occlusal contacts in each head postures(P<0.0001). Therefore, we need to check initial occlusal contacts in the altered head posture during occlusal analysis and adjustment of occlusal appliance and dental occlusion for diagnosis and treatment of temporomandibular disorder.