• The Journal of Engineering Research
• /
• v.3 no.1
• /
• pp.207-213
• /
• 1998

In order to fabricate ideal powders, new processing is necessary in which the solute atoms in solution rapidly move to mix each other to the degree of molecular level, the viscosity of solution should be low not to effect the moving of solute atoms, and the powders could be directly obtained as crystalline. Supercritical fluid is defined as condensed gas state up to its critical pressure and temperature. In this paper, supercritical fluid methods were studied as a new ceramic processing of powder preparation. The crystalline anatase powders of $TiO_2$ which are useful for photocatalyst materials were fabricated by hydrolysis of titanium(IV) ethoxide using water which was ethanol as a supercritical fluid.

• Journal of Powder Materials
• /
• v.29 no.2
• /
• pp.99-109
• /
• 2022

Powder flowability is critical in additive manufacturing processes, especially for laser powder bed fusion. Many powder features, such as powder size distribution, particle shape, surface roughness, and chemical composition, simultaneously affect the flow properties of a powder; however, the individual effect of each factor on powder flowability has not been comprehensively evaluated. In this study, the impact of particle shape (sphericity) on the rheological properties of Ti-6Al-4V powder is quantified using an FT4 powder rheometer. Dynamic image analysis is conducted on plasma-atomized (PA) and gas-atomized (GA) powders to evaluate their particle sphericity. PA and GA powders exhibit negligible differences in compressibility and permeability tests, but GA powder shows more cohesive behavior, especially in a dynamic state, because lower particle sphericity facilitates interaction between particles during the powder flow. These results provide guidelines for the manufacturing of advanced metal powders with excellent powder flowability for laser powder bed fusion.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.259-259
• /
• 1999

TiC ceramic particulate-reinforced titanium matrix composites were fabricated and the resultant densification, microstructure, and static and dynamic mechanical properties were studied. Comparing Ti with TiH₂powders as host materials for TiC ceramic reinforcement by pressureless vacuum sintering, TiH₂-started composites showed better sinterability and resistance to both elastic and plastic deformation than Ti-started ones. When TiH₂and TiH₂-45 vol.%TiC samples were hot pressed, TiH₂matrices transformed to alpha prime Ti and alpha Ti phase, respectively. It is interpreted that the diffusion of an alpha stabilizer carbon from TiC into the matrix is one of the plausible reasons far such a microstructural difference. The 0.2% offset yield strengths of the hot pressed TiH₂and TiH₂-45 vol.%TiC samples were 1008 and 1446 MPa, respectively, in a static compressive mode (strain rate of 1×$10^{-3}$/s). Dynamic compressive strengths of the samples were 1600 and 2060 MPa, respectively, at a strain rate of 4×10³/s.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.22 no.3
• /
• pp.203-210
• /
• 2006

Although porcelain fused to metal crowns made from non-precious metal have good mechanical properties, they also have disadvantages such as the poor biological acceptability and the low corrosional resistance. Titanium is used as the alternative metal for porcelain fused to metal crowns, in spite of difficulties in casting. For that reason non-precious alloy including titanium which is easy to cast is currently used. This study evaluated the bond strength between non-precious alloy including titanium and Ni-Cr alloy. $Tilite^{(R)}V$ as non-precious alloy including titanium, $Rexilium^{(R)}V$ as Ni-Cr alloy and $Omega900^{(R)}$ and $Vintage(Regular)^{(R)}$ as porcelain powders were used. The results were as follows. 1. In comparison with the kind of alloy, the bond strength of $Tilite^{(R)}V$ was lower than that of $Rexilium^{(R)}V$. There was no significant difference between two groups. 2. In comparison with the kind of porcelain powder, the bond strength of $Omega900^{(R)}$ was higher than that of $Vintage(Regular)^{(R)}$ in $Tilite^{(R)}V$. There was significant difference between two groups(p < 0.05).

• Journal of Korea Foundry Society
• /
• v.18 no.6
• /
• pp.593-603
• /
• 1998

Commercial ductile iron was coated with titanium and aluminum powders by low pressure plasma spraying and then irradiated with a $CO_2$ laser to produce anti-corrosive TiC composite layer. TiC carbides were precipitated homogeneously in a laser alloyed layer by in-situ reaction between carbon existed in the base metal and titanium with thermal sprayed coating. The formation of gas pores and brittle limited mixing zone with ledeburite microstructure in TiC composite layer were surpressed by the complementary alloying of aluminum. The hardness of TiC composite layer obtained by addition of titanium and aluminum was between 600 and 660 Hv, which was three times as high as the hardness of ferritic ductile iron. From the results of isothermal oxidation at 1123k for 24 hours in air, high temperature oxidation resistance of the TiC composite layer with aluminum was improved and doubled when compared with the TiC composite layer without aluminum.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.171-175
• /
• 1998

$Al_2O_3$-TiC composites were prepared from aluminum, titanium oxide, and carbon fibers by self-propagating high-temperature synthesis(SHS). After the SHS reaction, the TiC phase in the sample was found either fibrous or non-fibrous shape. The fraction of the fibrous TiC phase varied with the amount of $Al_2O_3$ diluent addition. The optimum amount of diluent to make fibrous carbide was determined to be 30%. The fibers were hollow inside and made of multiple grains with a composition of titanium carbide. The hollow fiber formation mechanism was suggested and discussed. The synthesized powders were consolidated to dense composites by hot pressing at $1750^{\circ}C$ under 30 MPa.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.540-541
• /
• 2006

SUS316L stainless steel, commercial pure Titanium and Ti-6Al-4V alloy powders applied by Mechanical Milling (MM) process are sintered by Hot Roll Sintering (HRS) process. Microstructure and mechanical properties of those HRS materials is investigated. The microstructures of materials produced by HRS process consist of fine grains and work-hardened structure, that is, the hybrid microstructure. Tensile test of the HRS material demonstrated the good mechanical properties. These results show that the HRS process is very effective to the improvement of mechanical properties in the SUS316L stainless steel, commercial pure Titanium and Ti-6Al-4V alloy.

• Korean Journal of Materials Research
• /
• v.18 no.7
• /
• pp.389-393
• /
• 2008

Nano-sized $TiO_2$-60 wt% SrO composite powders were synthesized by a sol-gel method using titanium isopropoxide and $Sr(OH)_2\;{\cdot}\;8H_2O$ as precursors. 3, -5, -7 wt%Ag spot-coated $TiO_2$-60 wt% SrO composite powders were synthesized by a Ag electroless deposition method using $TiO_2$-60 wt% SrO composite powders calcined at $1050^{\circ}C$, which mainly exhibited the $SrTiO_3$phase. However, a small number of rutile $TiO_2$, $Sr_2TiO_4$ and $SrO_2$ phases were also detected. In the Ag spot-coated powders synthesized by electroless deposition, nano-sized particles about 5-25 nm in diameter adhered to the $TiO_2$-60 wt% SrO composite powders. The photocatalytic activity of Ag spot-coated $TiO_2$-SrO and $TiO_2$-SrO composite powders for degradation of phenol showed that all of $TiO_2$-SrO composite powders were highly active under UV light irradiation. 7 wt%Ag spot-coated $TiO_2$-60wt.%SrO composite powders had a relatively higher photocatalytic activity than did $TiO_2$-SrO composite powders under visible light.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2004.04b
• /
• pp.50.1-50.1
• /
• 2004

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.935.2-935.2
• /
• 2006