• Korean Journal of Metals and Materials
• /
• v.47 no.3
• /
• pp.182-187
• /
• 2009

The molten salt electrolysis is applied to reduce titanium dioxide to titanium metal using calcium chloride as an electrolyte and the reaction mechanism of the reduction process is examined by analyzing the reaction products. The process conditions to obtain titanium metal for $900^{\circ}C$ correspond to 2.9~3.2 V and 24 hours. The reaction products for 2.9 V at $900^{\circ}C$ include irregular-shaped titanium oxides such as $Ti_4O_7$, $Ti_3O_5$ and $Ti_2O_3$ and polyhedral $CaTiO_3$. Using these microstructure analysis, the sequential reaction mechanism for the electrochemical reduction of titanium dioxide to titanium is proposed.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.2
• /
• pp.110-118
• /
• 2004

The corrosion of pure titanium (CP- Ti Grade 2) and titanium alloy (Ti6Al4V ELI) were studied under various conditions of simulated body fluids. The static immersion test and the electrochemical test were performed in accordance with ISO 10271 : 2001. For the electrochemical test, the open circuit potential was monitored as a function of time, and the cyclic polarization curve was recorded. The corrosion resistance was evaluated from the values of corrosion potential, passivation current density, breakdown potential, and the shape of hysteresis etc. The effects of alloy type, surface condition, temperature, oxygen, and constituents in the fluids such as acid, chloride were estimated. Both specimens had extremely low dissolution rate in the static immersion test. They showed strong passivation characteristics in the electrochemical test. They maintained negligible current density throughout the wide anodic potential range. The passive layer was not broken up to 2.0 V (vs. SCE). The hysteresis and the shift of passivation potential toward the anodic direction was observed during the reversed scan. The passivation process appeared to be accelerated by oxygen in air or that dissolved in the fluids. The passivation also proceeded without oxygen by the reaction of constituents in the fluids. Acid or chloride in the fluids, specially later weakened the passive layer, and then induced higher passivation current density and less shift of passivation potential in the reversed scan. CP-Ti Grade 2 was more reactive than Ti6Al4V ELI in the fluids containing acid or chloride, but thicker layer produced on its surface provided higher corrosion resistance.

• Corrosion Science and Technology
• /
• v.21 no.6
• /
• pp.454-465
• /
• 2022

The objective of this study was to determine effects of temperatures and pH of sodium chloride solution with MgCl₂ ions on corrosion resistance of duplex stainless-steel X2CrNiMoN22-5-3 (DSS) and Ti 6Al 2Nb1Ta1Mo (Ti). Effects of sodium chloride concentration on corrosion resistance were also studied. Corrosion behavior and pitting morphology of duplex stainless steel (DSS) and Ti alloys were evaluated through potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM). It was found that a decrease in pH significantly reduced the corrosion resistance of both alloys. Changes in chloride concentration and temperature had more substantial impact on corrosion behavior of DSS than on Ti alloys. Pitting corrosion was formed on DSS samples under all conditions, whereas crevice corrosion was developed on Ti samples with the presence of magnesium chloride at 90 ℃. In conclusion, magnesium chloride ions in an exceedingly strong acidity solution appear to interact with re-passivation process at the surface of these alloys and influence the resulting surface topography.

• Journal of Powder Materials
• /
• v.10 no.4
• /
• pp.228-234
• /
• 2003

In the present study, the focus is on the synthesis of titanium carbide/cobalt composite powder by the spray thermal conversion process using metallic salt solution as the raw materials. Two types of oxide powders of Ti-Co-O system were prepared by the spray drying of two types of metallic salt solutions : titanium chloride-cobalt nitrate and $TiO_2$ powder-cobalt nitrate solutions. These oxide powders were mixed with carbon black, and then these mixtures were carbothermal reduced under a flowing argon atmosphere. The changes in the phase structure and thermal gravity of the mixtures during carbothermal reduction were analysed using XRD and TG-DTA. In the case of using the titanium chloride-cobalt nitrate solution, it could not be obtained TiC/Co composite powder due to contamination of the impurities during the spray drying of the solution. However, in tile case of using the $TiO_2$ powder-cobalt nitrate scullion, TiC-15 wt. %Co composite powder could be synthesized by the spray thermal conversion process. The synthesized TiC-15 wt. %Co composite powder at 120$0^{\circ}C$ for 2 hours has average particle size of 150 nm.

• Korean Journal of Materials Research
• /
• v.14 no.12
• /
• pp.857-862
• /
• 2004

Production of titanium powder directly from tantalum oxides ($TiO_2$) pellet through an electronically mediated reaction (EMR) by calciothermic reduction has been investigated. Feed material ($TiO_2\;pellet$) and reductant (Ca-Ni alloy) were charged into electronically isolated locations in a molten calcium chloride ($CaCl_2$) bath at $950^{\circ}C$. The current flow through an external circuit between the feed (cathode) and reductant (anode) locations was monitored during the reduction of $TiO_2$. The current approximately 3.2A was measured during the reaction in the external circuit connecting cathode and anode location. After the reduction experiment, pure titanium powder with low nickel content was obtained even though Ca-Ni alloy was used as a reductant. These results demonstrate that titanium powder can be produced without direct physical contact between the feed and reductant. In certain experimental conditions, pure titanium powder with approximately $99.5\;mass\%$ purity was successfully obtained.

• Journal of Food Hygiene and Safety
• /
• v.20 no.2
• /
• pp.73-76
• /
• 2005

Center for Food Standard Evaluation, Korea Food and Drug AdministrationThis study was performed to compare analytical methods of nine synthetic food colors and six food color lakes in Korea, Japan, Joint FAO/WHO Expert Committee of Food Additives (JECFA), and USA. The experimental protocol of this study consists of three parts: titration method with titanium chloride, gravimetric and spectrophotometric method. To measure the total contents of food colors, Korea and Japan used titration method with titanium chloride, USA used the average value of titration method with titanium chloride equipped with Kipp generator and spectrophotometric method. Also, JECFA used titration method with titanium chloride equipped with KiPP generator. However, All the low organizations used gravimetric method to measure the total content of coloring matter on Food Red No.3. Although all organizations use various methods for analysis of coloring matters, total contents of coloring matter on food colors tested fell into the standard showing $85.08-96.40\%$ in synthetic food colors and $10.00-36.86\%$ in food color lakes.

• Polymer(Korea)
• /
• v.30 no.1
• /
• pp.64-69
• /
• 2006

A series of dinuclear half-sandwich titanium complexes with aryloxy substituent at titanium$[(\eta^5-cyclopentadienyl)(aryloxy)TiCl_2]_2[(CH_2)_n]$ (n=3, n=6, n=9) have been successfully synthesized and their styrene polymerization properties have been investigated. All complexes are characterized by $^1H\;NMR,\;^{13}C\;NMR$, elemental analysis, and mass spectrometry. In order to examine the catalytic properties of the dinuclear complexes styrene polymerization has beer conducted in the presence of MMAO. It was found that (i) all the prepared complexes were very effective catalyst for the production of SPS (syndiotactic polystyrene), (ii) the complex with the longest bridge between the two active sites exhibited greatest catalytic activity among the three catalysts, but produced SPS with the smallest molecular weight, (iii) the activities of dinuclear half-titanocens with aryloxy substitution at titanium metal were greater than those of the chloride substituted compounds. These results indicate that not only the nature of the bridge between the two active sites but also the property of substituents at the metal exert a significant influence on the polymerization behaviors of the dinuclear half-titanocene.

• Journal of the Korean Chemical Society
• /
• v.7 no.4
• /
• pp.299-303
• /
• 1963

A method of the colorimetric determination of titanium has been developed, based on the fact (IV) forms a stable blue complex with methylthymolblue(MTB) which is suitable for spectrophotometric determination of titanium in the concentration range of 0.2 to 22 $\mu$g per ml as $TiO_2$. The determination was carried out in the solution of pH range of 2.6 to 3.6, and the absorbancy of complex was at 600m$\mu$ with Coleman spectrophotometer. Titanium forms a 1:1 complex with MTB, which has a molar absorptivity, $1.1{\times}10^4$ at 600m\mu$. The effects of hydrogen ion concentration, reagent concentration, stability of complex, and hydrolysis were studied. Most of cations do not interfere seriously; however, many of anions such as oxalate, citrate, phosphate, chloride interfere in this determination.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.418-418
• /
• 2012

We fabricated a new type of hybrid film using molecular layer deposition (MLD). The MLD is a gas phase process analogous to atomic layer deposition (ALD) and also relies on a saturated surface reaction sequentially which results in the formation of a monolayer in each sequence. In the MLD process, polydiacetylene (PDA) layers were grown by repeated sequential surface reactions of titanium tetrachloride and 2,4-hexadiyne-1,6-diol with ultraviolet (UV) polymerization under a substrate temperature of $100^{\circ}C$. Ellipsometry analysis showed a self-limiting surface reaction process and linear growth of the hybrid films. Polymerization of the hybrid films was confirmed by infrared (IR) spectroscopy and UV-Vis spectroscopy. Composition of the films was confirmed by IR spectroscopy and X-ray photoelectron (XP) spectroscopy. The titanium oxide cross-linked polydiacetylene (TiOPDA) hybrid films exhibited good thermal and mechanical stabilities.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.1
• /
• pp.23-28
• /
• 1999

Au fine particles dispersed $TiO_{2}$ film was prepared on silica glass substrate by sol-gel dipping and firing process. The $TiO_{2}$ films were fabricated from the system of titanium tetraisopropoxide-EtOH-HCl-$H_{2}O$-hydrogen tetrachloroaurat (III) tetrahydrate. The conditions for the formation of clear solution and dissolving high concentration of Au compound were examined. Photoreduction process was adopted to control the size of gold metal particles. Phase evolution of matrix $TiO_{2}$ and variation of Au particle with UV irradiation were investigated by XRD, SEM, TEM and UV-visible spectrophotometer. The effect of CPCl (Cetylpyridinium chloride monohydrate) as a dispersion agent was evaluated.