• Journal of Environmental Science International
• /
• v.16 no.7
• /
• pp.785-791
• /
• 2007

The current study evaluated the technical feasibility of the application of titanium dioxide ($TiO_{2}$) photo-catalytic air cleaners for the disinfection of bioaerosols present in indoor air. The evaluation included both laboratory and field tests and the tests of hydraulic diameter (HD) and lamp type (LT). Disinfection efficiency of photocatalytic oxidation (PCO) technique was estimated by survival ratio of bacteria or fungi calculated from the number of viable cells which form colonies on the nutrient agar plates. It was suggested that the reactor coating with $TiO_{2}$ did not enhance the adsorption of bioaerosols, and that the UV irradiation has certain extent of disinfection efficiency. The disinfection efficiency increased as HD decreased, most likely due to the decrease in the light intensity since the distance of the catalyst from the light source increased when increasing the HD. It was further suggested that the mass transfer effects were not as important as the light intensity effects on the PCO disinfection efficiency of bioaerosols. Germicidal lamp was superior to the black lamp for the disinfection of airborne bacteria and fungi, which is supported by the finding that the disinfection efficiencies were higher when the germicidal lamp was used compared to the black lamp in the laboratory test. These findings, combined with operational attributes such as a low pressure drop across the reactor and ambient temperature operation, can make the PCO reactor a possible tool in the effort to improve indoor bioaerosol levels.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.11
• /
• pp.2077-2083
• /
• 2000

For the application of wet air oxidation(WAO) process reactive dyes, remazol blacks has been selected as the subject for this study. The rate of decomposition relating to the reaction temperature and catalyst has been summarized during the catalytic wet air oxidation reaction. When 1.5 gram per liter of platinum is added titanium-dioxide and the partial pressure is adjusted to 6 atmosphere at the reaction temperature exceeding $200^{\circ}C$, more than 95% of the remazol blacks dyes were decomposed. When the reaction temperature was raised to $200^{\circ}C$, $220^{\circ}C$ and $250^{\circ}C$, respectively, for 240 minutes after adding the catalyst, the remaining rate of ultraviolet absorbance had dropped significantly to 18%, 12%, and 4%. At the reaction temperature of $250^{\circ}C$, color removal efficiency was approximately 95% or more after 120 minutes from the beginning of the reaction.

• Journal of Powder Materials
• /
• v.21 no.2
• /
• pp.119-123
• /
• 2014

Pt has been widely used as catalyst for fuel cell and exhausted gas clean systems due to its high catalytic activity. Recently, there have been researches on fabricating composite materials of Pt as a method of reducing the amount of Pt due to its high price. One of the approaches for saving Pt used as catalyst is a core shell structure consisting of Pt layer on the core of the non-noble metal. In this study, the synthesis of Pt shell was conducted on the surface of $TiO_2$ particle, a non-noble material, by applying ultraviolet (UV) irradiation. Anatase $TiO_2$ particles with the average size of 20~30 nm were immersed in the ethanol dissolved with Pt precursor of $H_2PtCl_6{\cdot}6H_2O$ and exposed to UV irradiation with the wavelength of 365 nm. It was confirmed that Pt nano-particles were formed on the surface of $TiO_2$ particles by photochemical reduction of Pt ion from the solution. The morphology of the synthesized Pt@$TiO_2$ nano-composite was examined by TEM (Transmission Electron Microscopy).

• Bulletin of the Korean Chemical Society
• /
• v.35 no.12
• /
• pp.3521-3526
• /
• 2014

A magnetic sonophotocatalyst $Fe_3O_4@SiO_2@TiO_2$ is synthesized for the enhanced biodegradability of organophosphate pesticide. The as-prepared catalysts were characterized using different techniques, such as X-ray diffraction (XRD) and transmission electron microscopy (TEM). The radial sonophotocatalytic activity of $Fe_3O_4@SiO_2@TiO_2$ nanocomposite was investigated, in which commercial dichlorvos (DDVP) was chosen as an object. The degradation efficiency was evaluated in terms of chemical oxygen demand (COD) and enhancement of biodegradability. The effect of different factors, such as reaction time, pH, the added amount of catalyst on $COD_{Cr}$ removal efficiency were investigated. The average $COD_{Cr}$ removal efficiency reached 63.13% after 240 min in 12 L sonophotocatalytic reactor (catalyst $0.2gL^{-1}$, pH 7.3). The synergistic effect occurs in the combined sonolysis and photocatalysis which is proved by the significant improvement in $COD_{Cr}$ removal efficiency compared with that of solo photocatalysis. Under this experimental condition, the $BOD_5/COD_{Cr}$ ratio rose from 0.131 to 0.411, showing a remarkable improvement in biodegradability. These results showed that sonophotocatalysis may be applied as pre-treatment of pesticide wastewater, and then for biological treatment. The synthesized magnetic nanocomposite had good photocatalytic performance and stability, as when it was used for the fifth time, the $COD_{Cr}$ removal efficiency was still about 62.38%.

• Journal of Powder Materials
• /
• v.29 no.3
• /
• pp.207-212
• /
• 2022

Nanosized rutile titanium dioxide (TiO₂) is used in inorganic pigments and cosmetics because of its high whiteness and duality. The high quality of the white pigments depends on their surface coating technique via the solgel process. SiO₂ coatings are required to improve the dispersibility, UV-blocking, and whiteness of TiO₂. Tetraethyl orthosilicate (TEOS) is an important coating precursor owing to its ability to control various thicknesses and densities. In addition, we use Na₂SiO₃ (sodium silicate) as a precursor because of its low cost. Compared to TEOS, which controls the pH using a basic catalyst, Na₂SiO₃ controls the pH using an acid catalyst, giving a uniform coating. The coating thickness of TiO₂ is controlled using a surface modifier, cetrimonium bromide, which is used in various applications. The shape and thickness of the nanosized coating layer on TiO₂ are analyzed using transmission electron microscopy, and the SiO₂ nanoparticle behavior in terms of the before-and-after size distribution is measured using a particle size analyzer. The color measurements of the SiO₂ pigment are performed using UV-visible spectroscopy.

• Journal of the Korean Ceramic Society
• /
• v.55 no.3
• /
• pp.185-202
• /
• 2018

Photoelectrochemical (PEC) cells can convert solar energy, the largest potential source of renewable energy, into hydrogen fuel which can be stored, transported, and used on demand. In terms of cost competitiveness compared with fossil fuels, however, both photocatalytic efficiency and cost-effectiveness must be achieved simultaneously. Improvement of cost-effective, scalable, versatile, and eco-friendly fabrication methods has emerged as an urgent mission for PEC cells, and solution-based fabrication methods could be capable of meeting these demands. Herein, we review recent challenges for various nanostructured oxide photoelectrodes fabricated by solution-based processes. Hematite, tungsten oxide, bismuth vanadate, titanium oxide, and copper oxides are the main oxides focused on, and various strategies have been attempted with respect to these photocatalyst materials. The effects of nanostructuring, heterojunctions, and co-catalyst loading on the surface are discussed. Our review introduces notable solution-based processes for water splitting photoelectrodes and gives an outlook on eco-friendly and cost-effective approaches to solar fuel generation and innovative artificial photosynthesis technologies.

• Journal of Environmental Science International
• /
• v.11 no.6
• /
• pp.597-603
• /
• 2002

Photocatalytic degradation of phenol was carried out with UV-illuminated TiO$_2$-SiO$_2$ in aqueous suspension. TiO$_2$-SiO$_2$ catalysts were prepared by sol-gel method from the titanium isopropoxide and tetraethylorthosilicate at different Ti/Si ratio and some commercial TiO$_2$ catalysts were used as purchased. All catalysts were characterized by X-ray Diffraction(XRD) and BET surface area analyzer. The effect of reaction conditions, such as initial concentration of phenol, reaction temperature and catalyst weight on the photocatalytic activity was studied. In addition, TiO$_2$-SiO$_2$(49: 1) prepared by sol-gel method showed higher activity than commercial TiO$_2$catalysts on the photocatalytic degradation of phenol. The addition of SiO$_2$ into TiO$_2$hepled to increase the thermal stability of titania which suppressed the formation of anatase into rutile. The photocatalytic degradation of phenol showed pseudo-1st order reaction and the degradation rate increases with decreasing initial phenol concentration.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1338_1339
• /
• 2009

Dye-sensitized solar cell (DSC) consists of photo electrode, counter electrode and electrolyte. Photo electrode has titanium oxide layer with dye molecule to create electrons. And counter electrode is made of one layer that has catalytic ability for redox system such as the iodide/triiodide couple. Most DSC researchers use platinum as catalyst on counter electrode because platinum has good catalytic ability and conductivity. Platinum is doped on fluorine-doped tin oxide glass with different methods such as sputtering method, electrochemical method and so on. In this paper, we deposit platinum on counter electrode glass with two methods. One is the radio frequency (RF) sputtering method and the other is the chemical method with heating treatment. Finally, we compare the photovoltaic characteristics of DSCs that are assembled using two different counter electrodes.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.2
• /
• pp.139-148
• /
• 2002

Both UV Photolysis and Phtocatalytic Oxidation Processing are an emerging technology for the abatemant of Volatile Organic Compounds (VOCs) in atmospheric -pressure air streams. However, each process has some drawbacks of their own. The former is little known as an application for air pollution treatment, so it has been a rare choice in the field. Therefore we have to do more experiment and study for its application for treatment of VOCs. Although the latter has been used in the industrial fields, it still has a difficulty in decomposing high concentrations of VOCs. To solute these problems, we have been studying simultaneous application of those two technologies. We have studied the effects of background gas composition and gas temperature on the decomposition chemistry. It has shown that concentration of TCE and B.T.X., diameter of reactor, and wavelength of lamp have effects on decomposition efficiency. When using Photolysis Process only, the rates of fractional conversion of each material are found at TCE 79%, Benzene 65%, Toluene 68%, Xylene 76%. In case of Photocatalytic Oxidation Process only, the rates of fractional conversion decreased drastically above 30 ppm. When there two methods were combined, the rates of fractional conversion of each material are enhanced such as TCE 93%, Benzene 75%, Toluene 81%, Xylene 90%. Therefore, we conclude that the combination of Photolysis-Photocatalytic Oxidation process is more efficient than each individual process.

• Macromolecular Research
• /
• v.10 no.2
• /
• pp.108-114
• /
• 2002

Poly(butylene succinate) (PBS) prepolymers were prepared by the condensation polymerization of 1,4-butanediol (1,4-BD) and succinic atid (SCA) in the presence of titanium (VI) isoproxide(TPI) catalyst. The PBS prepolymers reacted with 1,4-BD or SCA to obtain hydroxyl or carboxylic acid group terminated PBS. High molecular weight linear or branched PBS was synthesized by a coupling reaction between hydroxyl and carboxylic acid group terminated PBS, or by a branching reaction between carboxylic acid group terminated PBS and glycerol as a branching agent. The weight average molecular weight of the prepared linear or branched PBS was in the range of 100,000-220,000. Both melting point and thermal stability of the high molecular weight linear and branched PBSs were somewhat higher than those of general PBS. From a tensile behavior by Instron test, modulus, tensile strength and elongation at break improved with increase in the molecular weight of the prepared PBS through the coupling or the branching reaction. In particular, the high molecular weight linear PBS had about 2.5 times higher value in modulus than the branched one.