• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.159-166
• /
• 2015

Silica which is used for reinforcing filler in tire industry is widely known as eco-friendly material exerting $CO_2$ reduction effect through decrease of rolling resistance and improvement of wet grip. Generally silica is classified as a highly polar filler because it contains a large number of silanol (Si-OH) group on its surface. And also silica gives a lower reinforcing effect than carbon black due to its poorer rubber-filler interaction. Therefore silica is treated with silane coupling agent or activator, then following the conventional rubber blend method, vulcanized sheets were prepared using a hot press, and cure characteristics, mechanical properties and abrasion resistance of the test specimens were investigated. It was found that with an increase in the silane coupling agent content the tensile strength, 300% modulus and abrasion resistance increased while Mooney viscosity decreased and crosslink density slightly increased with an increase of activator.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.1
• /
• pp.124-132
• /
• 2002

In this paper, we present a vision algorithm and method for input image improvement and preprocessing of dented and raised characters on the sidewall of tires. we define optical condition between reflect coefficient and reflectance by the physical vector calculate. On the contrary this work will recognize the engraved characters using the computer vision technique. Tire input images have all most same grey levels between the characters and backgrounds. The reflectance is little from a tire surface. therefore, it's very difficult segment the characters from the background. Moreover, one side of the character string is raised and the other is dented. So, the captured images are varied with the angle of camera and illumination. For optimum Input images, the angle between camera and illumination was found out to be with in 90$^{\circ}$. In addition, We used complex filtering with low-pass and high-pass band filters to improve input images, for clear input images. Finally we define equation reflect coefficient and reflectance. By doing this, we obtained good images of tires for pattern recognition.

• Proceedings of the KSPS conference
• /
• 2004.05a
• /
• pp.231-234
• /
• 2004

This paper describes an efficient method for improving the noise-robustness in speech recognition in a running car by considering wind noise. In driving car, mainly three kind of noises engine noise, tire noise and wind noise, are severely affect recognition performance. Especially wind noise is an important factor in driving car with window opened. We analyzed wind noise in various driving conditions that are 60, 80, 100 km/h with window fully opened, window half opened. We clarified that the recognition rate is significantly degenerated when the wind noise components in the frequency range above 200 Hz are large. We developed a preprocessing method to improve the noise robustness despite of wind noise. We adaptively changed the cutoff frequency of the front-end high-pass filter from 100 through 200 Hz according to the level of the wind noise components. By this method, the recognition rate is considerably improved for all kind of driving conditions

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.233-237
• /
• 2002

Vehicle Dynamics Control(VDC) has been a breakthrough and become a new terminology for the safety of a driver and improvement of vehicle handling. This paper examines the usefulness of a brake steer system (BSS), which uses differential brake forces for steering intervention in the context of VDC. In order to help the car to turn, a yaw moment can be achieved by altering the left/light and front/rear brake distribution. The steering function achieved through BSS can then be used to control lateral position in an unintended road departure system. A 8-DOF non-linear vehicle model including STI tire model will be validated using the equations of motion of the vehicle, and the non-linear vehicle dynamics. Since Fuzzy logic can consider the nonlinear effect of vehicle modeling, Fuzzy controller is designed to explore BSS feasibility, by modifying the brake distribution through the control of the yaw rate of the vehicle. The control strategies developed will be tested by simulation of a variety of situation; the possibility of VDC using BSS is verified in this paper.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.5
• /
• pp.82-91
• /
• 2003

Vehicle dynamics control (VDC) has been a breakthrough and become a new terminology for the safety of a driver and improvement of vehicle handling. This paper examines the usefulness of a brake steer system (BSS), which uses differential brake forces for steering intervention in the context of VDC, In order to help the car to turn, a yaw moment can be achieved by altering the left/right and front/rear brake distribution. The steering function achieved through BSS can then be used to control lateral position in an unintended road departure system. An 8-DOF non-linear vehicle model including STI tire model will be validated using the equations of motion of the vehicle, and the non-linear vehicle dynamics. Since fuzzy logic can consider the nonlinear effect of vehicle modeling, fuzzy controller is designed to explore BSS feasibility, by modifying the brake distribution through the control of the yaw rate of the vehicle. The control strategies developed will be tested by simulation of a variety of situation; the possibility of VDC using BSS is verified in this paper.

• Journal of Mechanical Science and Technology
• /
• v.19 no.3
• /
• pp.792-801
• /
• 2005

This paper discusses a dc motor equipped electric power steering (EPS) system and demonstrates its advantages over a typical hydraulic power steering (HPS) system. The tire-road interaction torque at the steering tires is calculated using the 2 d.o.f. bicycle model, in other words by using a single-track model, which was verified with the J-turn test of a real vehicle. Because the detail parameters of a steering system are not easily acquired, a simple system is modeled here. In previous EPS systems, the assisting torque for the measured driving torque is developed as a boost curve similar to that of the HPS system. To improve steering stiffness and return-ability of the steering system, a third-order polynomial as a torque map is introduced and modified within the preferred driving torques researched by Bertollini. Using the torque map modification sufficiently improves the EPS system.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.162-169
• /
• 2006

Steel cord which is used as reinforcement in car tires is produced by wet-drawing process. Recently the quality improvement of the steel cord product is demanded by the tire market. After cold drawing process, produced residual stresses have a harmful effect on the durability of the wire and become the cause which decreases the quality of the product. Therefore, to improve the quality of the steel cord product, the research regarding the method of residual stress relaxation is necessary. To evaluate the quality of the cold drawn wire, it is very important to measure the residual stress, because the residual stress decides a variety of the quality level which is demanded in the cold drawn wire. The aim of this study is to propose residual stress relaxation method in the drawn wire using FE-analysis. The validity of the analysis results was verified by Nano indentation test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.121-127
• /
• 2013

In this study, suspension geometry is controlled to improve vehicle handling performance. The toe and camber of the rear suspension is controlled independently by using a double knuckle structure designed to enhance the vehicle cornering stability. Camber and toe changes in the rear wheel during high speed turning maneuver are important factors that influence the vehicle stability. Toe in the rear outer wheel plays a dominant role in cornering. A control algorithm for the camber and the toe angle input is developed to carry out the control simulation of the vehicle such as single lane change, the steady state cornering, the double lane change and the step steering simulation. Effects of the camber and toe angle control are analyzed from the computer simulations. A double lane change simulation revealed that the suspension mechanism with variable camber angle and variable toe angle decreases the peak body slip angle and peak yaw rate, 50% and 10%, respectively.

• Journal of The Korean Association For Science Education
• /
• v.11 no.1
• /
• pp.97-115
• /
• 1991

The purpose of this study is in making a important way for in-service training of science teacthers. So the study was carried out to analyze the text books of in-service training school in Gyeongnam, Kyungpook, Junpook province and Pusan city and to survey teacher's opinion by questonnaires collected from teachers in Gyeongnam province. The result abtained are as follows : 1. The contents of. tire text books for in-service training course have very critical defference at each province. 2. Most of teachers wanted to get more updating information of the science and more comprehensive knowledge of higher level' of science subject. 3. In order to obtain comprehensive basic concept, develop of inquiry ability, and promote of scientific attitude, the thinking experiment which is selected to experimental subjects of secondary school are need to be selected. 4. The new text-book model for in-service training course should be developed, and the finnancial support will be required to develop such a text.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.366-372
• /
• 2002

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface deject as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know tile influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG4081-SUP7,SAE 9254, DIN 50CrV4, ) are made. This study shows the outstanding improvement of fatigue properties at tire case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.