• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.135-136
• /
• 2007

• 한국소음진동공학회논문집
• /
• 제17권3호
• /
• pp.274-281
• /
• 2007

Road traffic noise is not produced by any one factor rather it occurs as a composition of various factors. Its occurrence is made by running engine noise, tire frictional, and exhaust noise etc. The quality of the noise depends on the size of the vehicles, rotation and engine speed, vehicle load, package state of the road and incline etc. The occurrence of any noise level of heavy trucks appears louder than smaller vehicles and the noise levels produced differs according to speed and load etc between similar size vehicles. Other factors such as traffic density, average speed, mixing rate of heavy vehicles, and the distance between vehicles also generate road traffic noise. In this paper we examine 2, 4, and 6-lane roads in Jeonju. Consequently, this study examines the means used to measure road traffic noise. It was found that when there is a large traffic density and the average velocity is below 70 km/h, the noise level could receive a relative proper value by the current measuring means. But in the case of night-time, it was found that the current measuring method is inapposite.

• 한국도로학회논문집
• /
• 제10권2호
• /
• pp.47-55
• /
• 2008

본 논문에서는 3차원 유한요소법과 층탄성프로그램인 BISAR를 통해 얇은 아스팔트 콘크리트 표층의 피로균열 수명에 영향을 줄 수 있는 아스팔트 표층에서의 예측 인장변형률 결과를 광폭타이어와 바이어스 프라이 타이어를 이용하여 비교하였다. 본 논문에서는 11R22.5와 $10{\times}20$ bias ply 타이어의 접지압력 분포도를 분석하였으며, 서로 다른 해석방법을 이용하여 아스팔트 표층 하단부와 상단부에서의 예측인장변형률을 비교하였다. 분석결과, 두 타이어의 접지압 분포는 유사했지만 11R22.5광폭타이어가 $10{\times}20$ bias ply타이어와 비교해 상당히 큰 연직방향 접지압력을 보였다. 타이어 중앙에서 아스팔트 콘크리트 표층 하단부에서의 예측 인장변형률은 타이어 접지면적을 측정하여 충탄성프로그램인 BISAR에 적용한 BM해석법이 컸으며, 타이어 가장자리로부터 3.5cm 떨어진 곳에서의 상층부 예측 인장변형률은 3차원 접지압을 이용한 3차원유한요소법에 의한 해석이 가장 큰 값을 보였다.

• 대한교통학회지
• /
• 제28권3호
• /
• pp.119-130
• /
• 2010

교통사고의 재구성 해석은 도로와 사고흔적, 자동차 손상 등 다양한 자료들을 분석함으로서 이루어진다. 대부분의 자료들은 사고 해석에서 변수로 작용하며, 측정으로부터 구해지는 자료들은 조사자와 도구, 주어진 환경 등에 의해 측정 오차가 발생된다. 따라서 사고해석에서는 측정 오차에서 비롯되는 불확실성이 항상 존재한다. 본 연구는 불확실성이 존재할 가능성이 매우 높은 도로 기하구조와 타이어 흔적 등 길이와 마찰계수 등에 대해 반복 측정 실험을 함으로서 교통 사고해석에서의 불확실성을 정량화하였다. 또한 자동차 충돌 변형량의 사진 계측에 대한 불확실성에 대해서도 해석 결과를 제시하였다. 이러한 통계학적 분포들은 사고 재구성 불확실성을 추정하기 위해 입력 계수의 적절한 범위를 결정하는 것을 도울 수 있다.

• 한국소음진동공학회논문집
• /
• 제23권5호
• /
• pp.463-471
• /
• 2013

This paper presents design and control of electronic control suspension(ECS) equipped with controllable magnetorheological(MR) damper for passenger vehicle. In order to achieve this goal, a cylindrical type MR fluid damper that satisfies design specification of a middle-sized commercial passenger vehicle is proposed. After manufacturing the MR damper with design parameters, their field-dependent damping forces are experimentally evaluated and compared with those of a conventional damper. A quarter-vehicle MR ECS system consisting of sprung mass, spring, tire, controller and the MR damper is established in order to investigate the ride comfort performances. On the basis of the governing equation of motion of the suspension system, five control strategies(soft, hard, comfort, sport and optimal mode) are formulated. The proposed control strategies are then experimentally realized with the quarter-vehicle MR ECS system. Control performances such as vertical acceleration of the car body and tire deflection are evaluated in frequency domains on random road condition. In addition, performance comparison of WRMS(weighted root mean square) of the quarter-vehicle MR ECS system on random road are undertaken in order to investigate ride comfort characteristics.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.113-121
• /
• 2011

Rollover accident is one of the serious traffic accident and rollover accident takes high portion of all accident. The most common type of rollover is a tripped rollover which occupy 95% of all type of single-vehicle rollover. Tripped rollover occurs when a vehicle leaves normal road way and tripped by loose gravel, soil of fixed object such as guard rail, curbs and ditches. And the rest of the type of rollover is un-tripped rollover. An un-tripped rollovers that occurs during high-speed collision avoidance maneuvers. In this paper, presents the explanation of the un-tripped rollover test method and procedure, additionally this paper deals with various occurrence in the un-tripped test such as occurring excessive tire camber in the un-tripped test, tire side-wall contact with road surface and roll oscillation. And this paper analyzes the analysis of the roll rate amplitude in specific frequency through the FFT (Fast Fourier Transform) and the roll angle at the steering reverse timing which is the Fishhook test roll rate feedback time. Finally, this paper analyzes the relations between the estimated steady state roll gain and rollover stability.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.916-919
• /
• 2004

The monopole theory has long been used to model air-pumped effect from the elastic cavities in car tire. This approach models the change of an air as a piston moving backward and forward on a spring and equates local air movements exactly with the volume changes of the system. Thus, the monopole theory has a restricted domain of applicability due to the usual assumption of a small amplitude acoustic wave equation and acoustic monopole theory. This paper describes an approach to predict the air-pumping noise of a car ave with CFD/Kirchhoff integral method. The type groove is simply modeled as piston-cavity-sliding door geometry and with the aid of CFD technique flow properties in the groove of rolling car tyre are acquired. And these unsteady flow data are used as a air-pumping source in the next Cm calculation of full tyre-road geometry. Acoustic far field is predicted from Kirchhoff integral method by using unsteady flow data in space and time, which is provided by the CFD calculation of full tyre-road domain. This approach can cover the non-linearity of acoustic monopole theory with the aid of using Non-linear governing equation in CFD calculation. The method proposed in this paper is applied to the prediction of air-pumping noise of modeled car tyre and the predicted results are qualitatively compared with the experimental data.

• 대한토목학회논문집
• /
• 제26권6A호
• /
• pp.989-999
• /
• 2006

본 연구에서는 차량과 교량을 3차원으로 모델링하고, 교량의 노면조도 및 교량과 차량 사이의 상호작용을 고려하여 이동 차량이 교량을 통과할 때 교량의 선형동적해석을 수행할 수 있는 수치해석방법을 제시하였다. 3차원 차량모델에는 타이어의 접지폭을 고려하여 탠덤 다판스피링 차륜축의 피칭을 고려하여 단일차량인 2축과 3축 차량 및 5축 트랙터-트레일러를 각각 7-자유도, 8-자유도 미 14-자유도로 모델링하였다. 차량의 운동방정식은 Lagrange 방정식을 사용하여 유도하였고, 그 해는 Newmark-${\beta}$법을 사용하여 계산하였다. 교량의 노면조도는 평균값이 영인 정상확율분포롤 가정한 지수스팩트럴밀도를 사용하여 생성시켰다. 교량은 주형을 보요소로, 콘크리트 바닥판은 쉴요소를 이상화시켰으며 주형과 콘크리트 바닥판 사이는 Ragid Link를 사용하여 3차원으로 모델링하였다. 교량의 운동방정시은 모우드 중첩법을 사용하여 풀었다. 본 연구에서 제시한 수치해석방법으로 구한 결과와 Whittemoare 등과 Fenves 등이 실시한 실험값과 비교 검토하여 본 연구의 타당성을 입증하였다.

• International Journal of Automotive Technology
• /
• 제6권5호
• /
• pp.483-489
• /
• 2005

Based on a two-degree of freedom vehicle model, this paper investigates ride comfort for a heavy off-road vehicle mounted a nonlinear hydropneumatic spring, which is influenced by nonlinear stiffness and damping characteristics of the hydropneumatic spring. Especially, the damping force is derived by applying H. Blasius formula in modeling process according to the real physical structure of the hydropneumatic spring, and the established model of nonlinear stiffness characteristics have been validated by experiments. Furthermore, the effects of parameter variations of the hydropneumatic spring, such as initial charge pressure and damping coefficient, on body acceleration, suspension deflection and dynamic tire deflection are also investigated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.277-282
• /
• 2006

Road traffic noise is not produced by any one factor rather occurs as a composition of various factors. Its occurrence is made by running engine noise, tire frictional, and exhaust noise etc. The quality of the noise depends on the size of the vehicles, rotation and engine speed, vehicle load, package state of the road and incline etc. The occurrence of noise level of heavy trucks appears louder than smaller vehicles and the noise levels produced differs according to speed and load etc between similar size vehicles. Other factors such as traffic density, average speed, mixing rate of heavy vehicles, and the distance between vehicles also generate road traffic noise. In this paper we examine 2, 4, and 6-lane roads in Jeonju. Consequently, this study examined the means used to measure road traffic noise. It was found that when there is a large traffic density and the average velocity is below 70 km/hr, the noise level could receive a relative proper value by the current measuring means. But in the case of night-time, it was found that the current measuring method is inapposite.