• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.903-908
• /
• 2003

In this paper, we present an observer-based robust controller which achieves not only robust stability but also an performance robustness for linear uncertain discrete-time systems. The performance robustness means that comparing the transient behavior of the uncertain system with a desired one generated by the nominal system, the deterioration of control performance (i.e. the error between the real response and the desired one) is suppressed without excessive control input. The control law consists of a state feedback law for the nominal system and a compensation input given by a feedback form of an estimated error signal. In this paper, we show that conditions for the existence of the observer-based controller are given in terms of linear matrix inequalities (LMIs). Finally, a numerical example is given to illustrate the proposed technique.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.913-917
• /
• 1989

In this paper, the selection method of weighting matrices in the discrete-time LQ problem are suggested in order to improve the guaranteed stability margins, i.e. the gain and phase margins. The asymptotic properties of the solution of the algebraic Riccati equations are investigated by using the closed form solution of the difference Riccati equations. It is shown that the solution of the algebraic Riccati equations monotonically increases as the state weighting matrix Q or the control weighting matrix R increase. The increasing rate of the solution is shown to be much less than that of R for large R. It is also proven that the guaranteed stability margins increases as the ratio between Q and R decreases.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1324-1335
• /
• 2016

This article explores the speed regulation problem of permanent magnet synchronous motor (PMSM) systems subjected to unknown time-varying disturbances. A continuous sliding mode control (CSMC) technique is introduced for the speed loop to enhance the robustness of PMSM systems and eliminate the chattering phenomenon caused by high-frequency switch function in the conventional control law. However, the high control gain of the CSMC law in the presence of strong disturbances leads to large steady-state speed fluctuations for PMSM systems. In many application fields, PMSM systems are affected by time-varying disturbances instead of constant disturbances. For example, electric bicycles are usually affected by changing environmental disturbances, including wind speeds, road conditions, etc. These disturbances may be in the form of constant, ramp, and parabolic disturbances. Hence, a generalized proportional integral (GPI) observer is employed to estimate these types of disturbances. Then, the disturbance estimation method and the aforementioned CSMC method are combined to establish a composite sliding mode control method called the CSMC+GPI method for the speed loop of PMSM systems. Contrary to the conventional sliding mode control technique, the proposed method completely eliminates the chattering phenomenon caused by the switching function in the conventional control law. Moreover, a small control gain for the CSMC+GPI method is chosen by feed-forwarding estimated values to the speed controller. Hence, the steady-state speed fluctuations are small. The effectiveness of the proposed control scheme is verified by simulation and experimental result.

• Journal of Power Electronics
• /
• v.14 no.3
• /
• pp.572-579
• /
• 2014

As a non-linear time variant system, the four-quadrant line converter of an electric multiple unit (EMU) was expressed by linear time periodic functions near an operating point and modeled by a steady-state harmonic domain matrix. The components were then combined according to the circuit connection and relations of the feedback control loops to form a complete converter model. The proposed modeling method allows the study of the amplitude of harmonic impedances to explore harmonic coupling. Moreover, the proposed method helps provide a better design for the converter controllers, as well as solves the problem in coordination operation between the EMUs and the AC supply. On-site data from an actual $CRH_2$ high-speed train were used to validate the modeling principles presented in the paper.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.6
• /
• pp.1036-1055
• /
• 1992

In this paper the feedback linearization of the valve-controlled nonlinear hydraulic velocity control system and the implementation of the digital state feedback controller is studied. The $C^{\infty}$ nonlinear transfomation to the electro-hydraulic velocity control system, which transforms nonlinear system to linear equivalent one, is obtained. It is shown that this transformation is global one. The digital controller to this linearized model is obtained by using the one-step ahead state estimator and implemented to real plant. The proposed implementation method is easier than the other proposed methods and it is possible to control in real time. The experiment and simulation study show that the implementation of the digital state feedback controller based on the feedback linearized model is successful..

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.7
• /
• pp.668-673
• /
• 2010

Given a periodic reference signal or disturbance, repetitive control is a special control scheme to reduce a tracking error effectively by the periodic signal generator in the repetitive controller. In general, a repetitive controller is added on the existing feedback control system to improve the tracking performance. However, because the information used in the design of the feedback controller is not taken into account, the design problem of the repetitive controller is totally another problem irrespective of that of the feedback controller. In this paper, we present a more general method to design an add-on type repetitive controller using the information on the performance of the existing feedback control system. We first show that a robust stability condition of repetitive control systems is obtained using the well-known robust performance condition of general feedback control systems. It is also shown that we can obtain a steady-state tracking error described in a simple form without time-delay element if the robust stability condition is satisfied for the repetitive control system. From the obtained results, several design criterions for repetitive controller are provided. Through the simulation study, the feasibility of the proposed method is verified.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.6 no.1
• /
• pp.60-68
• /
• 2003

This paper proposes an optimum design method of structural and control systems, using a 2-D truss structure as an example. The structure is subjected to initial static loads and disturbances. For the structure, a FEM model is formed. Using modal transformation, the equation of motion is transformed into modal coordinates, in order to decrease D.O.F. of the FEM model. To suppress the effect of the disturbances, the structure is controlled by an output feedback $H_{\infty}$ controller. The design variables of the combined optimal design of the control-structure systems are the cross sectional areas of truss members. The structural objective function is the structural weight. The control objective function is the $H_{\infty}$ norm, the performance index of control. The second structural objective function is the energy of the response related to the initial state, which is derived from the time integration of the quadratic form of the state in the closed-loop system. In a numerical example, simulations have been perform. Through the consideration of structural weight and $H_{\infty}$ norm, an advantage of the combined optimum design of structural and control systems is shown. Moreover, since the performance index of control is almost nearly optimiz, we can acquire better design of structural strength.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.5 s.54
• /
• pp.57-65
• /
• 2003

This paper proposes an optimum design method of structural and control systems, using a 2-D truss structure as an example. The structure is subjected to initial static loads and disturbances. For the structure, a FEM model is formed. Using modal transformation, the equation of motion is transformed into modal coordinates, in order to decrease D.O.F. of the FEM model. To suppress the effect of the disturbances, the structure is controlled by an output feedback $H_{\infty}$ controller. The design variables of the combined optimal design of the control-structure systems are the cross sectional areas of truss members. The structural objective function is the structural weight. The control objective function is the $H_{\infty}$ norm, the performance index of control. The second structural objective function is the energy of the response related to the initial state, which is derived from the time integration of the quadratic form of the state in the closed-loop system. In a numerical example, simulations have been perform. Through the consideration of structural weight and $H_{\infty}$ norm, an advantage of the combined optimum design of structural and control systems is shown. Moreover, since the performance index of control is almost nearly optimiz, we can acquire better design of structural strength.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.184-188
• /
• 2001

In this paper, a new fully digital control method for single-phase UPS inverter, which is based on the double control loop such as the outer voltage control loop and inner current control loop, is proposed. The inner current control loop is designed and implemented in the form of internal model control and takes the presence of computational time-delay into account. Therefore, this method provides an overshoot-free reference-to-output response. In the proposed scheme, the outer voltage control loop employing P controller with resonance model implemented by a DSP is introduced. The proposed resonance model has an infinite gain at resonant frequency, and it exhibits a function similar to an integrator for AC component. Thus the outer voltage control loop causes no steady state error as regard to both magnitude and phase. The effectiveness of the proposed control system has been demonstrated by the simulation and experimental results respectively.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.spc2
• /
• pp.278-287
• /
• 2005

In this paper a new excitation control scheme that improves the transient stability of multi machine power systems is proposed. To this end the backstepping technique is used to transform the system to a suitable partially linear form. On this system, a combination of both feedback linearization and adaptive control techniques are used to confront the nonlinearities. As shown in the paper, the resulting nonlinear control law ensures the uniform boundedness of all the state and estimated variables. Furthermore, it is proven that all the error variables are uniformly ultimately bounded (DUB) i.e. they converge to arbitrarily selected small regions around zero in finite-time. Simulation tests on a two generator infinite bus power system demonstrate the effectiveness of the proposed control.