• Journal of the Korean Operations Research and Management Science Society
• /
• v.24 no.3
• /
• pp.63-72
• /
• 1999

Recent studies on the Constant Bit Rate and Variable Bit Rate transmissions have mainly focused on the frame by frame encoder rate control based on the quantization parameter. With the existing approaches it is difficult to guarantee a consistent video quality. Also, the rate control overhead is too high for the real-time video sources. In this paper, a channel rate allocation scheme based on the control period is proposed to transmit a real-time video, in which the control period is defined by a pre-specified number of frames or group of pictures. At each control period, video traffic information is collected to determine the channel rate at the next control period. The channel rate is allocated to satisfy various channel rate constraints such that the buffer occupancy at the decoder is maintained at a target level. If the allocated channel rate approaches the level at which the negotiated traffic descriptions may be violated, the encoder rate is decreased through adjusting quantization parameters in the MPEG encoder. In the experimental results, the video quality and the overflow and underflow probabilities at the buffer are compared at different control periods. Experiments show that the video quality and the utilization of network bandwidth resources can be optimized through the suitable selection of the control period.

• Journal of Applied Reliability
• /
• v.11 no.4
• /
• pp.433-445
• /
• 2011

Duty cycle is determined as the ratio of operating time to total time. Duty cycle in reliability prediction is one of the significant factors to be considered. In duty cycle application, non-operating time failure rate has been easily ignored even though the failure rate in non-operating period has not been proved to be small enough. Ignorance of non-operating time failure rate can result in over-estimated system reliability calculation. Furthermore, utilization of duty cycle in reliability prediction has not been evaluated in its effectiveness. In order to address these problems, two reliability models, such as MIL-HDBK-217F and RIAC-HDBK-217Plus, were used to analyze non-operating time failure rate. This research has proved that applying duty cycle in 217F model is not reasonable by the quantitative comparison and analysis.

• Journal of the Korean Society of Safety
• /
• v.32 no.2
• /
• pp.46-51
• /
• 2017

This paper presents classification of domestic fire detector using response time index. Response time is measured using fire detector distributed in Korea, and the response time index is estimated. Plunge test prescribed by FM is conducted to measure response time of fire detector. The detector used to test is fixed temperature type(thermistor and bimetal type) and rate of rise temperature type(thermistor and pneumatic type). The nominal operation temperature of fixed temperature type detector is $70^{\circ}C$ and rate of rise temperature is $15^{\circ}C/min$. The fixed temperature type is measured 7 products, and the rate of rise temperature type is measured 5 products. The results show that in case of fixed temperature type(thermistor) is classified "Quick" or "Standard" and fixed temperature type(bimetal) is not classified. The rate of rise temperature type(thermistor) is classified "Fast" or "Ultra Fast" and the rate of rise temperature type(pneumatic) is classified "Very Fast" or "Ultra Fast". The pneumatic type shows more fast response than thermistor type. Also these results indicate the fixed temperature type(bimetal) is not suitable for early stage fire detection.

• Korean Journal of Digital Imaging in Medicine
• /
• v.15 no.1
• /
• pp.21-26
• /
• 2013

To be investigated and measures to reduce the medical exposure of patients to change the Epidural Injection time Fluoroscopy Pulse Rate in this study. Was conducted in 50 patients who underwent surgery Epidural Injection performed by interventional care of Konkuk University Hospital from January to April 2013. The treatment time with the change of Pulse rate, is measured in minutes fluoroscopy time, and measured the area dose (${\mu}Gym^2$) and depth dose (mGy). Using the Image J program, to measure the PSNR and SNR. The fluoroscopy time as a result surgery, there was no significance in the statistical analysis, and depth dose is 34.3 to 34.9%, was reduced from 35.8 to 38.7% the area dose. It is possible to reduce the appropriate Pulse rate, to reduce the dose without statistical analysis significance fluoroscopy time.

• ETRI Journal
• /
• v.18 no.2
• /
• pp.61-74
• /
• 1996

We propose two new rate control schemes to improve MPEG-2 rate control in view of visual quality when scene changes happen. Two proposed schemes are characterized by real-time and non real-time improvement to reduce the impact of scene changes. We also propose a new target-bit prediction method using spatial activity of pictures and present a simple and efficient scene change detection scheme using signed difference of mean absolute difference (MAD). Computer simulation results show that the proposed real-time algorithm effectively alleviates visual quality degradation after scene changes. The proposed non real-time algorithm gives maximum 2 dB improvement in peak signal-to-noise ratio (PSNR) at a scene-changed picture, compared with MPEG-2 rate control scheme and it shows better quality than the real-time one.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.210-212
• /
• 1996

Random drift rate (i.e., random drift in angle rate) of a gyro represents the major error source of inertial navigation systems that are required to operate over long time intervals. It is uncorrectable and leads to an increase in the error with the passage of time. In this paper a technique is presented for analyzing random process from experimental data and the results are presented. The problem of estimating the a priori statistics of a random process is considered using time averages of experimental data. Time averages are calculated and used in the optimal data-processing techniques to determine the statistics of the random process. Therefore the contribution each component to the gyro drift process can be quantitatively measured by its statistics. The above techniques will be applied to actual gyro drift rate data with satisfactory results.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.22-28
• /
• 2007

Using woodceramics made from sawdust board of pine thinning logs, changes in surface temperature were investigated, by the heating rate and keeping time at maximum temperature. The heating rate of $2^{\circ}C/min$ and keeping time at maximum temperature 1 hour, were the highest in surface temperature. Also, it was found that woodcermics maintained heat for a long time because the descending velocity of their surface temperature was slower than that of the heater.

• Industrial Engineering and Management Systems
• /
• v.10 no.4
• /
• pp.247-254
• /
• 2011

In this paper, we study a single-machine scheduling problem with deteriorating processing time of jobs and multiple rate-modifying activities which reset deteriorated processing time to the original processing time. In this situation, the objective function is to minimize total completion time. First, we formulate an integer programming model. Since the model is difficult to solve as the size of real problem being very large, we design an improved genetic algorithm called adaptive genetic algorithm (AGA) with spontaneously adjusting crossover and mutation rate depending upon the status of current population. Finally, we conduct some computational experiments to evaluate the performance of AGA with the conventional GAs with various combinations of crossover and mutation rates.

• Journal of the Korean Institute of Plant Engineering
• /
• v.23 no.4
• /
• pp.29-38
• /
• 2018

Through process quality information, the time required for process quality analysis has been drastically shortened, the process defect rate has been reduced, and the manufacturing lead time has been shortened and the on-time delivery rate has been improved. Therefore, The purpose of this study is to develop a quality information analysis system model that effectively shortens the time required for process quality analysis in automobile safety belt parts manufacturing process. As a result of experiments on communication operation between manufacturing execution system (MES) quality server, injection machine control computer, injection machine programmable logic controller (PLC) and terminal, in analyzing quality information, the conventional handwriting input method took an average of 20 minutes, but the new multi-network method took about 2 minutes on average. In addition, the process defect rate was reduced by 13% and the manufacturing lead time was shortened from 28 hours to 20 hours. The delivery compliance rate improved from 96 to 99%.

• Advances in materials Research
• /
• v.11 no.1
• /
• pp.41-57
• /
• 2022

This paper is focused on delamination analysis of a multilayered inhomogeneous viscoelastic beam subjected to linear creep under constant applied stress. The viscoelastic model that is used to treat the creep consists of consecutively connected units. Each unit consists of one spring and two dashpots. The number of units in the model is arbitrary. The modulus of elasticity of the spring in each unit changes with time. Besides, the modulii of elasticity and the coefficients of viscosity change continuously along the thickness, width and length in each layer since the material is continuously inhomogeneous in each layer of the beam. A time-dependent solution to the strain energy release rate for the delamination is derived. A time-dependent solution to the J-integral is derived too. A parametric analysis of the strain energy release rate is carried-out by applying the solution derived. The influence of various factors such as creep, material inhomogeneity, the change of the modulii of elasticity with time and the number of units in the viscoelastic model on the strain energy release rate are clarified.