• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2006년도 추계 학술대회논문집
• /
• pp.167-176
• /
• 2006

In this paper we show that solutions of the nonlinear Nernst-Planck equation possesses the quadruple-layer structure near the interface when the electrolyte receives a high frequency forcing such as a high-frequency alternating current. Very near to the interface wall, the well-known, classical Stern layer exists. Near to the Stern layer we have the secondly thin layer (to be called inner layer in this paper) where the ion concentrations behave under the same frequency as the external forcing. However, in this layer, the positive and negative ion concentrations develop with the time phase 180-degree different from each other. Next to this second layer, we have the third layer (called middle layer) in which two ion concentrations change with the time period double the forcing, and both concentrations behave in the same time phase. In the outermost layer, i.e. the forth layer, (called outer layer) the ion concentrations show the same-phase development as the third one but decaying very slowly in time. Our assertion is mostly based on the 1-D numerical simulation for the Nernst-Planck equation under a high frequency AC field assuming that the quadruple layer is very thin compared with the length scale representative of the bulk region.

• 한국멀티미디어학회논문지
• /
• 제19권12호
• /
• pp.1992-1999
• /
• 2016

In layered communication architecture, each layer is designed to service its own functions to higher layer while getting serviced by lower layer. Usually layered architectures are not optimized in a total view of whole services and functions. So cross layer design pursues performance enhancements by optimizing in various ways. In LTE, MAC layer uses HARQ mechanism and RLC layer uses ARQ mechanism for retransmission. According to the 3GPP 36.331 specification, two layers' cooperation may not happen in an optimized way. This paper suggests an adaptive MAC layer approach which RLC layer's function might be initiated in MAC layer in advance to utilize MAC layer's idling wasting time for RLC layer's next decision. This adaptive ARQ method in MAC layer speeds up the next retransmission and reduces the overall transmission time. Emulation shows the improved performance in total retransmission time and retransmission success ratio. In wireless shadow area, the retransmission occurs frequently. Our approach has strong points in this poor wireless condition.

• 반도체디스플레이기술학회지
• /
• 제3권3호
• /
• pp.11-17
• /
• 2004

This research has been progressed for adhesive improvement of the Polyimide/Buffer layer/Cu at the COF(Chip On Film) which induced as the alternative plan about high concentration of a circuit or substrates according to demands of miniaturization and high efficiency of various electronic equipment. RF plasma equipment was applied to when plama pretreatment was performed for improvement of adhesive strength of PI and Cr as the buffer layer. Experimental fluents were a species of the buffer layer, depositied time and the ratio of $O_2$/Ar when performed to plasma pretreatment. The results are that Ni was superior to Cr at peel test according to a species of the buffer layer, peel strength and Cu THK were showed proportional relation to deposition structure of the same buffer layer and sample of the Cr depositied time(30 sec) and Cu depositied time(20 min) was showed good adhesion to peel test according to Cr's depositied time and Cu's depositied time. When perform PI's plasma pretreatment peel strength and $O_2$/Ar ratio were showed proportional relation. But $O_2$/Ar(2/5) was best condition since then decreased.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 1996년도 학술발표회
• /
• pp.15-18
• /
• 1996

A general description of sprinkler activation time in compartment-fire-generated smoke layers is made. For calculation of the time hot layer temperature is obtained from two-layer zonal model and time constant of sprinkler is measured. Upper-layer thickness at the instant of sprinkler activation is also presented with changes of opening area. The outputs of the present study provide inputs for the interaction modeling of sprinkler spray and compartment fire environment, which simulates fire suppression phenomena.

• 한국수산과학회지
• /
• 제54권4호
• /
• pp.480-488
• /
• 2021

The term residence time is defined as the time taken for substances in a system to leave the system and is a useful concept to explain the physical environment characteristics of a coastal area. It is important to know the spatial characteristics of the residence time to understand the behavioral properties of pollutants generated in a marine system. In this study, the spatial distribution of average residence time was calculated for Gangjin Bay, Korea, using a hydrodynamic model including a particle tracking module. The results showed that the average residence time was about 10 days at the surface layer and about 20 days at the bottom layer. Spatially, this was the longest residence time in the southwestern sea. There was no significant difference in average residence time at the surface layer due to freshwater discharge, but spatial variation at the bottom layer was larger. The average residence time at the bottom layer decreased in the southwestern area due to freshwater discharge and increased in the northern area. This result suggests that the residence time of anthropogenic pollutants may have a large spatial difference depending on the freshwater discharge, and thus the time taken to influence cultured organisms may also vary.

• 한국세라믹학회지
• /
• 제37권3호
• /
• pp.263-270
• /
• 2000

The Pt/copper oxide/n-Si electrodes were fabricated by depositing copper oxide thin film of 500${\AA}$ and very thin Pt layer on the n-type (100) Si substrate. hotoelectrochemical properties and stability profiles of the electrodes were investigated as a function of deposition time of Pt layer. As the deposition time of Pt layer increased up to 10 seconds, the photocurrent and quantum efficiency were increased and then decreased with further depositing time. The better cell stability was observed for the electrode with longer deposition time. The improvements in above photoelectrochemical properties indicate that Pt layer acts as a catalyst layer at electrode/electrolyte interface as well as a protective layer. The decreasing tendency of the photocurrent and efficiency for the electrode with Pt layer deposited above 20 seconds was explained as an increases in probbility of electron-hole pair recombination and also the absorbing photon loss at electrode surface due to the excessive thickness of Pt layer. The results were confirmed by impedance spectroscopy, mutiple cycle voltammograms and microstructural analyses.

• 열처리공학회지
• /
• 제5권4호
• /
• pp.215-223
• /
• 1992

This study has been performed to investigate into some effects of temperature, gas mixing ratio and time on the optical microstructure, hardness and wear characteristics of medium carbon alloy steel treated by plasma nitriding. The results obtained from the experiment are summarized as follows: (1) Optical micrographs of AISI 4140 steel plasma-nitrided by the double stage technique have revealed that the nitrided layer is composed of the compound layer and the diffusion layer. The variation in temperature at the first stage gives effects, on the formation of compound layer and the growth rate is shown to be relatively fast at $460^{\circ}C$. (2) The thickness of compound layer has been found to increase with increasing nitrogen percentage in the gas mixture and the holding time. It is therefore recommended that a shorter holding time and a lower nitrogen percentage are more effective to produce a tougher compound layer and a diffusion layer only. (3) X-ray diffraction analysis for AISI 4140 steel has shown that the compound layer consist of ${\gamma}^{\prime}-Fe_4N$ and ${\alpha}-Fe$ and that tough compound layer diffustion layer only can be obtained by the double stage plasmanitriding process. (4) There is also a tendency that the total hardened layer depth increases with increasing temperature, time and nitrogen percentage in the first stage during the double stage plasma nitriding. (5) The wear resistance of plasma nitrided specimens has been found thobe considerably increased compared to the untreated specimens and the amount of increment has appeared to increase further with increasing nitriding temperature, holding time and notrogen percentage of gas mixture in the first stage treatment.

• 한국전기전자재료학회논문지
• /
• 제16권1호
• /
• pp.60-64
• /
• 2003

In this study, the inorganic thin-film passivation layer was newly adopted to protect the organic layer from moisture and oxygen. Using the electron beam evaporation system, the various kinds of inorganic thin-films were deposited onto the organic layer and their interface properties between organic and inorganic layer were investigated. In this investigation, the MgO layer showed the most suitable properties, and based on this result, the time dependent emission properties were estimated for the OLED with and without passivation layer. In this experiment, we can see that the time-dependent emission properties of MgO passivated OLED had longer life-time compared to non-passivated OLED. Therefore, we can consider that the MgO thin film is one of the most suitable candidates for the thin-film passivation layer of OLED.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.224-227
• /
• 2002

The relationship between the discharge aging time and the superficial layer thickness of MgO thin film was investigated in an AC PDP. The discharge characteristics of an AC PDP with the various aging time were evaluated by discharge aging experiments. We find the presence of a superficial lay which is related to the discharge characteristics during aging process. The superficial layer of MgO thin film was observed by Transmission Electron Microscope (TEM). It was found that the superficial layer thickness of MgO was dependent on discharge aging time.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(1)
• /
• pp.57-60
• /
• 2001

This paper has studied the WAP packet transmission time, using WTP SAR algorithm. One method that is improved transfer ability, SAR fragmented WTP total message down from upper layer and then packet is transmitted to RLP frame time slot. In this paper, we analysis the transmission time of WAP packet with variable HLP layer size on the CDMA wireless channel for next generation systems as well as PCS, DCS. From the results, we can obtain the WAP packet transmission time and optimal WTP packet size.