• Tribology and Lubricants
• /
• 제36권2호
• /
• pp.82-87
• /
• 2020

In thrust bearings, the thrust collar and bearing surface need to be parallel to each other to ensure that all pads share the same load. In rotating machines, the shaft system cannot achieve perfect alignment. Misalignment of the thrust collar results in some pads supporting a higher load than others and excessive loads being placed on some pads. Consequently, high loads and high temperatures may occur in the bearing. Thus, in this study, we aim to analytically evaluate the performance of a misaligned non-equalizing direct lubricated tilting pad thrust bearing. We define the oil film thickness of the misaligned thrust bearing using the Byrant angle. Additionally, we calculate the pressure distribution and temperature distribution of the thrust bearing using the generalized Reynolds equation and energy equation. The design limit of the thrust bearing is defined by the load and temperature. Therefore, we evaluate the allowable misalignment angle as the limit of the maximum load and temperature. The analysis results demonstrate that an increase in the speed and load corresponds to a smaller allowable misalignment angle. However, as this is not the same for all thrust bearings, evaluating the allowable misalignment angle at each thrust bearing is essential.

• 전기전자학회논문지
• /
• 제18권2호
• /
• pp.282-290
• /
• 2014

본 논문은 1인승 전기차량의 임베디드 전동 제어장치 설계를 제안하였다. 제안된 임베디드 장치는 PIC18F8720 프로세서, 16Mb flash ROM, 32Mb SDRAM과 신호처리회로로 설계되었다. 제안된 1인승 전기차량은 4KW 인휠 BLDCM, $180^{\circ}$ 도통 공간 벡터제어 3상 전압형 인버터, PID 속도제어기와 전동제어 장치와 임베디드 제어장치로 구성된다. 이 1인승 전기차량은 역 3륜 형태의 기계적인 구조를 가지고 있으며, 인휠 BLDCM과 틸팅 기능을 가지는 조향 메카니즘이 적용되었다. 또한 제안된 임베디드 전동제어장치의 성능은 PEV에 대한 Lab 실험과 도로 주행시험을 통하여 검증하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1454-1457
• /
• 2003

This study was carried out to minimize the lifting force of a two hinge type stand mechanism. This unit is designed for the display devices in order to enhance the ergonomics for effective height adjustment and maintenance at any preferred position. The unit will be very useful for the mechanism fabricated with a coil spring and disc springs as a torque generator. The maximum and the minimum torque value should be calculated initially for the smooth lift. And the reasonable torque distribution is necessary to prevent any AUTO LIFT and AUTO Drooping at any position because the torque generated by coil spring is more sensitive than disc spring in tilting the position. Therefore, the analysis of the coil spring is requisite to issue the specific torque value depending on the distorted angle with securing reliability of a long time storage condition. After the theoretical torque value was calculated, the evaluation was carried out by making a proto-type sample, then distorted angle was updated by experiment. The result of this study can readily be applied to various units for the optimization of the smooth lift.

• 패션비즈니스
• /
• 제22권5호
• /
• pp.125-136
• /
• 2018

This study intended to develop a motorcycle safe vest that can be prepared against accidents by mounting a smart module (with built-in sensor) on the safe vest in order to emphasize safety among functional aspects of the motorcycle clothing. The research method investigated professional books, prior research, and Internet data to examine the characteristics of motorcycle wear and the theoretical examination of smart wear, and analyzed the functional characteristics of the design by reviewing smart jacket and vest design cases for motorcycles currently on the market. As a results of study an interface device sensor, which contains a sensor with IMU(Intertial Measurement Unit) and CPU(Central Processing Unit), was inserted into a motorcycle top in order to draw attention to the safety of motorcycle riders. The IMU sensor attached to the vest detected the tilting motion of the rider to either left or right side to obtain data on left or right direction, sudden stop, and so forth and displayed left or right turn signal and sudden stop sign on the backplate (back) through the LED module. As for charging the device to operate LEDs, a generator, which is designed to convert the heat energy in the exhaust into electric energy, was used to efficiently self-produce the power required to operate LEDs of the top while riding.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.3065-3072
• /
• 2011

PID Control Data Base creation device of DCU is safety operation technology of train door. For keeping the normal condition of door, measured value of regular condition and unusual(trouble detected) condition should be recorded by encoding. The door should be measured itself as this value is compared with standard vale. If it's condition of the door and for reaching the datum point and ot does self-diagnosis. This aim for Technical Realization is that carry out safety train operation by using the Estimation Data Base and protect before door-trouble.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 B
• /
• pp.448-450
• /
• 1998

Global competition of automotive market and affordable prices of electronic components become the major reason that automotive industries rapidly employ a large number of electric and electronic systems to improve vehicle performance and to meet various regulations such as emission, fuel efficiency, and safety. Especially, the provision of a motor-driven steering column (MDSC) for luxury vehicle is getting popular for drivers' convenience. In this study, an MDSC is developed, which provides several intelligent features such as the manual operation for tilting and telescoping the steering wheel, and the save/recall operation for three different steering wheel positions. In addition, the fault detection algorithm is developed.

• 한국운동역학회지
• /
• 제17권2호
• /
• pp.113-121
• /
• 2007

The purpose of this study was to determine the effect of three different plates($0^{\circ}$, $10^{\circ$}, $20^{\circ}$)under heels on the lower limb muscles and erector spinae during squat exercise. Ten high school korean traditional wrestling players(age: $18.5{\pm}0.7$, weight: $1972.2{\pm}128.5N$, height: $177.8{\pm}6.0cm$, weight of barbell: $1004.5{\pm}132.4N$) performed squat exercise using three different tilting plates under heels at a cadence of 40beats/sec with 80% one repetition maximum load. Surface electrodes were placed on the participants' left and right erector spinae, and rectus femoris, vastus medialis, vastus lateralis, tibialis anterior, biceps femoris, medial gastrocnemius, and lateral gastrocnemius in the right lower extremity. One S-VHS camcorder(Panasonic AG456, 60fields/s) was placed 10m to the side of the participant. To synchronize the video and EMG data, a synchronization unit was used for this study. Average and Peak IEMG values were determined for each participant. For each variable, a one-way analysis of variance was used to determine whether there were significant differences among three different tilting plates under heels. When a significant difference was found in plates type, post hoc analyses were performed using the Tukey procedure. A confidence level of p<.05 was used to determine statistical significance. As a result of this study, maximum nEMG values of the tibialis anterior in $0^{\circ}$ plates was significantly higher than the corresponding values for the other plates during the knee extension. This increased activation in the tibialis anterior muscle indicates an increase in displacement of center of gravity of body. It is very likely that additional muscle activation are needed to stop the forward and backward movement. The results also showed that muscular activities of quadriceps femoris and erector spinae were decreased with increasing angle of plates. This suggests that increasing angle of plate may help to sustain the balance and posture of squat exercise. It is considered that very few significant differences were found among three different plates($0^{\circ}$, $10^{\circ}$, $20^{\circ}$) since elite players with much experience in squat exercise, were chosen as a participant of this study. In order to obtain meaningful results regarding the tilting angle of heel plates in squat exercise, kinetic and 3D kinematic analysis will be needed in the future study.

• 비파괴검사학회지
• /
• 제28권2호
• /
• pp.157-163
• /
• 2008

본 논문에서는 대형 구조물의 감시를 위한 새로운 광섬유 경사계를 제시한다. 이 경사계 시스템은 센서 헤드, 광 조절부 그리고 신호처리부로 이루어진다. 또한 본 시스템은 무아레 프린지 현상의 원리를 이용하며 광섬유라는 새로운 광측정 장치를 적용하였다. 이를 통해, 센서 시스템은 가격이 저렴하고 전자기학 잡음에 강하며 설치가 용이해 졌다. 실제로 본 논문에서는 저비용의 광전자 구동 시스템을 포함한 실제 시제품을 성공적으로 개발하였다. 그리고 실제 실험을 통해 센서의 선형성을 포함한 성능을 검증하였고 이를 통해 실제 토목구조물의 처짐각을 측정할 수 있는 광섬유 경사계 시스템으로서의 가능성과 성능을 입증하였다.

• 비파괴검사학회지
• /
• 제35권1호
• /
• pp.18-24
• /
• 2015

철도 시설물의 상태를 종합적으로 동시에 검측하고 건전성 평가가 가능한 고속 종합검측시스템을 위해 열차의 위치검지 정보는 필수불가결하다. 본 논문에서는 위치검지를 위한 위치 기술중 관성센서의 측정과 분석에 대해 다룬다. 관성센서의 가속도 정보와 각속도 정보에 대해 진폭과 주파수 관점에서 분석하였고, 진동 및 열차 동역학에 대한 검토도 이루어졌다. 이러한 검토 결과와 GPS 정보를 이용하여 호남선 나주역부터 일로역까지 한국형 틸팅열차의 위치검지를 수행하였다. 이와 같은 센서 측정치와 열차의 거동에 대한 동기화된 분석은 열차위치검지 시스템의 설계와 성능 향상에 도움을 줄 수 있다.

• Journal of Biosystems Engineering
• /
• 제37권6호
• /
• pp.342-351
• /
• 2012

Purpose: Aerial spraying with an agricultural unmanned helicopter became a new paradigm in the agricultural practice. Laterally tilting behavior of a conventional agricultural helicopter, resulting in the biased down-wash and uneven spray deposit is a physically intrinsic phenomenon while hovering and cruise flights. Authors studied and developed a roll-balanced agricultural helicopter with a raised pylon tail rotor system. In this study, the attitude of the roll-balanced helicopter was determined using the Kalman filter algorithm, and the quality of roll balancing of a bare-airframe helicopter was evaluated. Methods: Instantaneous attitudes were estimated using the advantage of gyroscope, followed by the long term correction and prediction using accelerometer data for the advantage of convergence. The attitudes of the fuselage were calculated by applying the Kalman filter algorithm. The spraying maneuver of the helicopter was performed at a field of 50 m long, and the attitude data were acquired and evaluated. Results: The determination of attitude using the inertial measurement unit(IMU) and Kalman filter was reliable and practical. The intrinsic attitude of the developed helicopter was stable and roll-balanced. The deviation of roll angle was ${\pm}6.3^{\circ}$ with an average of $0^{\circ}$, referring to roll-balanced. Conclusions: Handling quality of the roll attitude determined to be steadily balanced. The balancing behavior of the developed helicopter would result in an even spray pattern during aerial application.