• Transactions of the Society of Information Storage Systems
• /
• v.7 no.1
• /
• pp.19-24
• /
• 2011

Holographic Data Storage System, one of the next generation data storage devices, is a 2-dimensional page oriented memory system using volume holograms in writing and retrieving process. Recently photopolymer with disc type substrate was selected as a media for the Holographic Data Storage System. The disc tilt occurs when the media rotates and the external disturbance applies. The disc tilt causes the change of the angle between the reference beam and the media, the data cannot be retrieved with the right angle or other data page is retrieved. The tilt is generated in a 2-axis direction (tangential, radial). The tangential tilt direction is the same with the multiplexing plane, while the radial tilt direction is a perpendicular to the multiplexing plane. In this research we propose 2-axis tilt angle servo system. The tilt errors are measured by using external photo detector and the additional red laser. Then the tangential direction tilt is compensated by using the galvano mirror. Also the radial direction tilt is compensated by the rotating prism between the relay lens in the reference field. Finally we confirm the compensation results through the Signal to Noise Ratio(SNR) and Bit Error Rate(BER).

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.1
• /
• pp.199-206
• /
• 2017

Environmental noise can degrade the performance of speech recognition system. This paper presents a procedure for performing cepstrum based feature compensation to make recognition system robust to noise. The approach is based on direct compensation of spectral tilt to remove effects of additive noise. The noise compensation scheme operates in the cepstral domain by means of calculating spectral tilt of the log power spectrum. Spectral compensation is applied in combination with SNR-dependent cepstral mean compensation. Experimental results, in the presence of white Gaussian noise, subway noise and car noise, show that the proposed compensation method achieves substantial improvements in recognition accuracy at various SNR's.

• Journal of Astronomy and Space Sciences
• /
• v.40 no.4
• /
• pp.237-245
• /
• 2023

Laser communication has been considered as a novel method for earth observation satellites with generation of high data volume. It offers faster data transmission speeds compared to conventional radio frequency (RF) communication due to the short wavelength and narrow beam divergence. However, laser beams are refracted due to atmospheric turbulence between the ground and the satellite. Refracted laser beams, upon reaching the receiver, result in angle-of-arrival (AoA) fluctuation, inducing image dancing and wavefront distortion. These phenomena hinder signal acquisition and lead to signal loss in the course of laser communication. So, precise alignment between the transmitter and receiver is essential to guarantee effective and reliable laser communication, which is achieved by pointing, acquisition, and tracking (PAT) system. In this study, we simulate the effectiveness of tip/tilt compensation for more efficient laser communication in the satellite-ground downlink. By compensating for low-order terms using tip/tilt mirror, we verify the alleviation of AoA fluctuations under both weak and strong atmospheric turbulence conditions. And the performance of tip/tilt correction is analyzed in terms of the AoA fluctuation and collected power on the detector.

• Journal of the Optical Society of Korea
• /
• v.13 no.4
• /
• pp.451-455
• /
• 2009

We present a numerical procedure that compensates for tilt phase aberration in in-line digital holography by computing the period of interference patterns in the reconstructed phase image. This method enables the reconstruction of correct and accurate phase information, even if strong tilt aberrations exist. Example applications of tilt aberration compensation are shown for a tilted plate, a micro-lens array, and a thin film transistor. This method is convenient because it uses only one hologram and no hardware to minimize the tilt aberration.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.782-787
• /
• 2002

In optical disk drives (ODD), the demands of high data density and high speed have been increasing rapidly to achieve high data capacity and data transfer rate. The short wavelength laser, High NA objective lens, and high track following performance are needed to raise data density and data rate. For high-performance actuator, the improvement of linearity and acceleration become more important. Also, 3-axis actuator for active tilt compensation is introduced to overcome the decrease in disk tilt tolerance which is induced by short wavelength laser. In this paper, a hybrid type 3-axis actuator is presented and a new yoke structure, which can reduce the interaction between yoke and moving magnet, is designed to keep the efficiency of magnetic circuit. Experimental results show the validity of the yoke in the hybrid type actuator.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.2
• /
• pp.192-198
• /
• 2013

This paper presents the stabilization and design of a pan-tilt control part for the directional pan-tilt system for shipboard directional equipment. In order to control each control axis with compensation for ship motion, the 2 degree of freedom(2DOF) PID controller is designed and its parameters are tuned using a real-coded genetic algorithm(RCGA). Simulation demonstrates the effectiveness of the 2 DOF PID controller tuning.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.12-16
• /
• 2003

This paper presents a compensation method for a temperature-dependent gain tilt in L-band erbium-doped fiber amplifier using a voltage-controlled attenuator. The gain tilts in the L-band of 1570-1605 nm due to a temperature change have negative slopes, whereas they have positive slopes for the increasing optical input powers in a saturation region. The proposed method utilizes these opposite gain variations to compensate for the gain tilt over a wide range of temperature. While applying forty channels with a channel spacing of 100 GHz in the L-band and changing the ambient temperature from 0 to $50^{\circ}C$, the compensation method maintained the gain deviation within 1 dB.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.5
• /
• pp.190-196
• /
• 2015

In this paper, we propose multiple location error compensation algorithm for GPS/INS fusion using kalman filter and introduce the way to reduce location error in 9-axis navigation devices for implementing inertial navigation technique. When evaluating location, there is an increase of location error. So navigation systems need robust algorithms to compensate location error in GPS/INS fusion. In order to improve robustness of 9-axis inertial sensor(mpu-9150) over its disturbance, we used tilt compensation method using compensation algorithm of acceleration sensor and Yaw angle compensation to have exact azimuth information of the object. And it shows improved location result using these methods combined with kalman filter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.226-233
• /
• 2003

There are many researches going on to develop the information storage devices using Blue-ray disc and DVD as a demand for high-density information storage devices is highly increasing. This high-density information storage device requires a short-wave laser and objective lens of high numerical aperture set in fer its operation. And, that brings out rapid decrease of tilt tolerance. Therefore, it is necessary that an actuator should control tilt motions to get a stable signal. In this paper, a new mathematical form of 3-D.O.F coupled model is formulated and magnetic circuit in constraints is most effectively designed with the use of the moving coil type actuator in higher sensitivity. Further, this paper presents a tilt coil whose rotational center point is put on that of the lens through the variation of tilt coil and proposes a 3-axis actuator with high sensitivity improved in its dynamic property through its structure analysis.

• Transactions of the Society of Information Storage Systems
• /
• v.3 no.4
• /
• pp.191-195
• /
• 2007

The optical disc drive has used a high NA objective lens and a shorter wavelength laser diode for high recording density. But high NA and shorter wavelength cause several margins to become short. Focusing and tracking servo has to be more accurate and active tilt compensation mechanism is also needed for coma aberration compensation. In this paper, we proposed 3-axis moving magnet type actuator. For 3-DOF motion, moving coil actuator has to be equipped with 6 wires for supplying 3 independent signals. However, moving magnet type actuator doesn't need to change the configuration of wires because coils are in stator. So, we added a tilt mechanism to the 2-axis moving magnet actuator which is designed in previous research. Addition of the tilt mechanism cuts down the focus sensitivity. So, maximization the tilting sensitivity and securing the focusing sensitivity are objectivities of this research. DOE (design of experiments) procedures of electromagnetic circuit are performed for parameter study and the optimization is also performed to maximize the tilt sensitivity. And then the final design is suggested and its performance is verified by FE simulation.