• Korean Journal of Soil Science and Fertilizer
• /
• v.34 no.1
• /
• pp.64-70
• /
• 2001

To verify the newly developed decision assisting expert system for nitrogen fertilizer application NES to Illinois cornfields, a couple of N rate studies from Dr. Howard and five Illinois Agricultural Experiment Stations were applied. Four types of recommendations including the current Illinois recommendation, Hoeft recommendation, NES, and maximum economic recommendation were compared with each other for the crop yields, profits, recovery rate, and N losses to cornfields. The N rate of NES recommendation, considering productivity index (PI), soil organic matter content (SOM), and pre-sidedressing nitrate concentration (PSNT) level, was the lowest in comparison to those of other recommendations. However, N recovery rate in NES was generally higher and the resulting N loss was lower than others. But, adherence to the recommendations may also reduce farmers income if environmental expense did not considered. Therefore, NES will be more effective by adding the factors including environmental expense, tillage systems, crop rotation, and other agricultural management parameters.

• Journal of Drive and Control
• /
• v.17 no.4
• /
• pp.133-140
• /
• 2020

Traction performance of a tractor varies depending on soil conditions. Sinkage and slip of the driving wheel for tractor frequently occur in a reclaimed land. The objective of this study was to develop a tractor suitable for a reclaimed land. Traction performance was evaluated according to soil conditions of reclaimed land and paddy field. Field experiments were conducted at two test sites (Fields A: paddy field; and Field B: reclaimed land). The tractor load measurement system was composed of an axle rotation speed sensor, a torque meter, a six-component load cell, GPS, and a DAQ (Data Acquisition System). Soil properties including soil texture, water content, cone index, and electrical conductivity (EC) were measured. Referring to previous researches, the tractor traveling speed was set to B3 (7.05 km/h), which was frequently used in ridge plow tillage. Soil moisture contents were 33.2% and 48.6% in fields A and B, respectively. Cone index was 2.1 times higher in field A than in field B. When working in the reclaimed land, slip ratios were about 10.5% and 33.1% for fields A and B, respectively. The engine load was used almost 100% of all tractors under the two field conditions. Traction powers were 31.9 kW and 24.2 kW for fields A and B, respectively. Tractive efficiencies were 83.3% and 54.4% for fields A and B, respectively. As soil moisture increased by 16.4%, the tractive efficiency was lowered by about 28.9%. Traction performance of tractor was significantly different according to soil conditions of fields A and B. Therefore, it is necessary to improve the traction performance of tractor for smooth operations in all soil conditions including a reclaimed land by reflecting data of this study.

• Journal of Biosystems Engineering
• /
• v.12 no.3
• /
• pp.30-41
• /
• 1987

The geometrical shape of a plow bottom may be the most important factor affecting the performance of a plow for a given soil and operating conditions. There are various designs of the Jaenggi (Korean plow) available commercially, which may be different from each other and from the plow (Western plow) in respect to the shape and performance. This study was intended to investigate the geometrical characteristics of Jaenggi. The coordinate digitizer equipped with 3 potentiometers was designed and manufactured for measurement of the shape of curved plane of moldboard and share. The digitizer was connected to a microcomputer having the data acquisition system. This device was used to analyze the plow bottoms of 5 differently-made Jaenggis and one cylindrical plow. The results of the study are summarized as follows: 1. It was possible to measure easily and quickly the curved plane of plow bottom and to plot the view on three major plans using the coordinate digitizer electrically connected to a microcomputer system. 2. The shape of five Jaenggi bottoms analyzed could be characterized by the cutting angle having the range of $33-42^{\circ}$, the maximum share-lift angle of $41-50^{\circ}$, and the setting angle of moldboard wing of $46-70^{\circ}$. The most critical difference of the shape factors between the Jaenggi and the plow was found in the maximum share-lift angle, the former was more than twice as much as the latter. 3. The analysis of the shape of Jaenggi bottoms showed that the share projections on 3 major plans had a varied triangle, which was quite different from that of plow bottom. Especially, it was analyzed that the shape of furrow slice for the Jaenggi had a skewed rectangle, leaving a considerable height of the ridge at the furrow bottom. 4. The dihedral angle was similar range of $30-85^{\circ}$ for the all bodies investigated, but the directional angle was somewhat different from each other. The difference in directional angle was $5^{\circ}$ for the plow, $20^{\circ}$ for the Jaenggi A and $30^{\circ}$ for the Jaenggi B. 5. Area of the spherical representation region was 0.0328 for the plow, 0.1194 for the Jaenggi A and 0.1716 for the Jaenggi B. This may indicate that the plow came close to a working surface and the Jaenggi A and the Jaenggi B departed from a working surface to a somewhat greater extent.

• Korean Journal of Environmental Agriculture
• /
• v.21 no.2
• /
• pp.136-143
• /
• 2002

Emission of methane and nitrous oxide affected by nitrogen fertilizer materials were measured simultaneously in rice paddy fields under flooding and intermittent irrigation in 2000. Studies focused on mitigating $CH_4$ emission from rice paddy fields are summarized and the possibilities and limits applied to world's rice cultivation are discussed. The mitigation options are water management, soil amendments, organic matter management, different tillage, rotation, and cultivar selection. Altering water management, in particular promoting midseason aeration by short-term drainage, is one of the most promising strategies, although these practices may be limited to the rice paddy fields where the irrigation system is well prepared. The test site was divided into two water managements: a continuously flooded plot which was maintained flooded by constant irrigation from May to September, and an intermittently drained plot in which short-term (20days) draining practices were performed one times during the flooding period. By total emission of GHGs converted by global warming potential (GWP), flooding plots were higher 170$\sim$208% than interimittent irrigation plots. For emission of GHGs in fertilizer materials, it was high in the order of Swine slurry>Urea+Rice straw>Urea>LCU. Basing on GHGs emission of urea fertilization under flooding as baseline GWP of urea fertilization and Latex-coated urea under intermittent irrigation showed lower GHGs emission by 41.4% and 55.8 respectively. In this case fertilizer use efficiency (kg unhulled rice/ of applied N) were 18.2$\sim$20.2 and 18.7$\sim$19.0 and 9.3 and 5.8$\sim$6.6 for Swine slurry and LCU and Urea+Rice straw and Urea in the continuously flooded and intermittently drained plot.

• Korean Journal of Environment and Ecology
• /
• v.24 no.2
• /
• pp.186-193
• /
• 2010

In order to examine the traits of sluice gate water control, halophyte community formation and their inter-relations in Saemangeum, both water level condition and halophyte community formation were analyzed periodically and spatially on the topographic map with Surfer, Saemageum Spatial Analysis System, and related field reports. The traits of water level condition are that average water level in the growing period of halophytes was similar to annual average water level, annual low level and high level appeared in the growing period, and water level was usually maintained within a range of -1.0m~0.5m above mean sea level, but it has changed more frequently year by year. Routine water level control, natural disaster prevention, construction, and civil appeal took major percentages of the reasons for sluice gate's opening and shutting. Since 2007, not only the overall control frequency of sluice gate but also its control frequency for construction and natural disaster prevention have increased outstandingly. Halophyte community had formed at a rate of 1,209ha/year in the 4,315 ha land in 2008, 6.3 times larger than in 2005, and 2,382 ha above around 1.0m was estimated to be artificially vegetated, 89.1 % of the 2,673ha-size sown area. High water level was found to be a more possible determinant than average water level or low water level in halophyte community formation and it was thought to be secondary factors whether tillage was conducted or/and whether surface sealing formed.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1263-1263
• /
• 2001

The amounts of organic matter present in soil and the rate of soil organic matter (SOM) turnover are influenced by agricultural management practice, such as rotation, tillage, forage plow down direct seeding and manure application. The amount of nutrients released from SOM is highly dependent upon the state of the organic matter. If it contains a large proportion of light fractions (low-density) more nutrients will be available to the glowing crops. However, if it contains mostly heavy fractions (high-density) that are difficult to breakdown, then lesser amounts of nutrients will be available. The state of the SOM and subsequent release of nutrients into the soil can be predicted by NIRS as long as a robust regression equation is developed. The NIRS method is known for its rapidity, convenience, simplicity, accuracy and ability to analyze many constituents at the same time. Our hypothesis is that the NIRS technique allows researchers to investigate fully and in more detail each field for the status of SOM, available moisture and other soil properties in Alberta soils for precision farming in the near future. One hundred thirty one (131) Alberta soils with various levels (low 2-6%, medium 6-10%, and high >10%) of organic matter content and most of dry land soils, including some irrigated soils from Southern Alberta, under various management practices were collected throughout Northern, Central and Southern Alberta. Two depths (0- 15 cm and 15-30 cm) of soils from Northern Alberta were also collected. These air-dried soil samples were ground through 2 mm sieve and scanned using Foss NIR System 6500 with transport module and natural product cell. With particle size above 150 microns only, the “Ludox” method (Meijboom, Hassink and van Noorwijk, Soil Biol. Biochem.27: 1109-1111, 1995) which uses stable silica, was used to fractionate SOM into light, medium and heavy fractions with densities of <1.13, 1.13-1.37 and >1.37 respectively, The SOM fraction with the particle size below 150 microns was discarded because practically, this fraction with very fine particles can't be further separated by wet sieving based on density. Total organic matter content, mechanical texture, ash after 375$^{\circ}C$, and dry matter (DM) were also determined by “standard” soil analysis methods. The NIRS regression equations were developed using Infra-Soft-International (ISI) software, version 3.11.

• Journal of Biosystems Engineering
• /
• v.3 no.1
• /
• pp.1-19
• /
• 1978

Power tiller is a major unit of agricultural machinery being used on farms in Korea. About 180.000 units are introduced by 1977 and the demand for power tiller is continuously increasing as the farm mechanization progress. Major farming operations done by power tiller are the tillage, pumping, spraying, threshing, and hauling by exchanging the corresponding implements. In addition to their use on a relatively mild slope ground at present, it is also expected that many of power tillers could be operated on much inclined land to be developed by upland enlargement programmed. Therefore, research should be undertaken to solve many problems related to an effective untilization of power tillers on slope ground. The major objective of this study was to find out the travelling and tractive characteristics of power tillers being operated on general slope ground.In order to find out the critical travelling velocity and stability limit of slope ground for the side sliding and the dynamic side overturn of the tiller and tiller-trailer system, the mathematical model was developed based on a simplified physical model. The results analyzed through the model may be summarized as follows; (1) In case of no collision with an obstacle on ground, the equation of the dynamic side overturn developed was: $$\sum_n^{i=1}W_ia_s(cos\alpha cos\phi-{\frac {C_1V^2sin\phi}{gRcos\beta})-I_{AB}\frac {v^2}{Rr}}=0$$ In case of collision with an obstacle on ground, the equation was: $$\sum_n^{i=1}W_ia_s\{cos\alpha(1-sin\phi_1)-{\frac {C_1V^2sin\phi}{gRcos\beta}\}-\frac {1}{2}I_{TP} \( {\frac {2kV_2} {d_1+d_2}\)-I_{AB}{\frac{V^2}{Rr}} \( \frac {\pi}{2}-\frac {\pi}{180}\phi_2 \} = 0 $$ (2) As the angle of steering direction was increased, the critical travelling veloc\ulcornerities of side sliding and dynamic side overturn were decreased. (3) The critical travelling velocity was influenced by both the side slope angle .and the direct angle. In case of no collision with an obstacle, the critical velocity $V_c$ was 2.76-4.83m/sec at $\alpha=0^\circ$, $\beta=20^\circ$ ; and in case of collision with an obstacle, the critical velocity $V_{cc}$ was 1.39-1.5m/sec at $\alpha=0^\circ$, $\beta=20^\circ$ (4) In case of no collision with an obstacle, the dynamic side overturn was stimu\ulcornerlated by the carrying load but in case of collision with an obstacle, the danger of the dynamic side overturn was decreased by the carrying load. (5) When the system travels downward with the first set of high speed the limit {)f slope angle of side sliding was $\beta=5^\circ-10^\circ$ and when travels upward with the first set of high speed, the limit of angle of side sliding was $\beta=10^\circ-17.4^\circ$ (6) In case of running downward with the first set of high speed and collision with an obstacle, the limit of slope angle of the dynamic side overturn was = $12^\circ-17^\circ$ and in case of running upward with the first set of high speed and collision <>f upper wheels with an obstacle, the limit of slope angle of dynamic side overturn collision of upper wheels against an obstacle was $\beta=22^\circ-33^\circ$ at $\alpha=0^\circ -17.4^\circ$, respectively. (7) In case of running up and downward with the first set of high speed and no collision with an obstacle, the limit of slope angle of dynamic side overturn was $\beta=30^\circ-35^\circ$ (8) When the power tiller without implement attached travels up and down on the general slope ground with first set of high speed, the limit of slope angle of dynamic side overturn was $\beta=32^\circ-39^\circ$ in case of no collision with an obstacle, and $\beta=11^\circ-22^\circ$ in case of collision with an obstacle, respectively.

• Korean Journal of Agricultural Science
• /
• v.11 no.1
• /
• pp.160-175
• /
• 1984

This study was carried out to analyze the effects of the revolution and forwarding speed of the rotary blade and the edge curves which were $30^{\circ}$ and $40^{\circ}$, on the power requirement of rotary tillage. In this study, the revolutions of the rotary blade considered were 204, 243, 285, 360 rpm, and the forwarding speeds of the rotary system considered were 29.40cm/sec, 46.93em/sec. The power requirements of rotary blade were measured by a dynamic strain gage systems at the soil bin which was filled with artificial soil. The results of the study were summarized as follows: 1. The response surface analysis showed that the revolution and forwarding speed of the rotary shaft had an interacting influence on the torque requirement of the rotary blade. The mathematical model developed by the above was repersented as follow. $$T=a_0+a_1V+a_2R +a_3VR+a_4VR^2$$ where, $a_0=constant$ $a_1,\;a_2,\;a_3,\;a_4=coefficients$ V=forwarding speed of the rotary system. (em/sec) R=revolution of the rotary shaft. (rpm) T=tilling torque requirement. (kg-m) 2. When the maximum tilling torque requirement was analyzed, ${\partial}T/{\partial}R$ was decreased with the increasing revolution of rotary shaft, while ${\partial}T/{\partial}V$ was increased, which was minimum at 200~220 rpm. When the forwarding speeds were increased, ${\partial}T/{\partial}R$ was decreased with increasing rate. 3. When the mean tilling torque requirement was analyzed, ${\partial}T/{\partial}V$ was constant at 320~360 rpm and ${\partial}T/{\partial}R$ was decreased with increasing rate along with the increasing revolution of rotary shaft. 4. When the mean tilling torgue requirement per unit volume of soil was analyzed, ${\partial}T/{\partial}V$ was minimum at 270~300 rpm. ${\partial}T/{\partial}R$ for the forwarding speeds of 29.40cm/sec and 46.93cm/sec was same as that for 280~290 rpm. 5. Increasing the edge curves of the rotary blades, the tilling torque requirement was increased. But other studies showed that the smaller the edge curve, the more straw could be wrapped on blades which resulted in increasing torque requirements. Therefore, the edge curve of rotary blade should be considered for the future study.

• Korean Journal of Plant Resources
• /
• v.30 no.5
• /
• pp.556-564
• /
• 2017

Appropriate soil temperature and early planting of potato is very important for the successful potato-soybean cropping system in central region of South Korea. This experiment was carried out to determine the effect of mulching materials on the growth and yield of potato (Solanum tuberosum L.). Five different mulch treatments were had been applied on an upland soil as follows ; no mulch (NM), transparent film (TF), transparent film + additional transparent film (TF + ATF), black film (BF), and black film + additional transparent film (ATF). In the period of sowing time to removing additional films, mean soil temperature of the treatments was in the order of TF+ATF > TF > BR+ATF > BF as $20.3^{\circ}C$ > $18.5^{\circ}C$ > $16.1^{\circ}C$ > $15.4^{\circ}C$, respectively and that of NM was $13.8^{\circ}C$. The accumulated soil temperature was TF > NM > BF during the removing additional films to earthing at inter-tillage. On the changes in the soil temperature during a whole day, the temperature in the BF was lower than NM during around 18:00 PM to 12:00 NM, while NM was higher than BF in the time period of 10:00AM to 21:00PM. The sequence of potato sprout emergence was 15 > 18 > 20 > 22 days of TF+ATF, TF, BF+ATF, and BF, respectively and that of NM was 24 days. Comparing to the NM, potato sprout emergence was observed on the TF+ATF treated plot as early as 9 days. At 10 days before harvest, the significant difference in the tuber dry weight had been observed and the sequence tuber weight was in the order of TF > TF+ATF > BF+ATF > BF > NM. The potato yields of TF, TF+ATF, and BF+ATF were increased of 40.7, 37.3, and 22% as compared to NM ($2,805kg\;10a^{-1}$), but almost same yield in the BF. The differences of tuber dry weight and potato yields was co-related with the temperature rise of soil by the application of mulching materials on soil. Based on these results, application of mulching film had been very effective to increase the tuber size and the yield of potato by the temperature rise during seedling stage of potato. Transparent mulching was better than black mulching especially for the emergence of sprout of potato in relation to minimizing cooling injury.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.56 no.2
• /
• pp.119-123
• /
• 2011

To use barley as a green manure crop, this study has been conducted in Suwon, Gyeonggi-do to establish the barley green manure (BGM)-rice cropping system with emphasis on soil incorporation date and BGM density. The nitrogen (N) contents of rye and barley, grass green manure crops, were 1.4~2.4% at early growth stage and decreased rapidly to 0.6~1.0% at late growth stage. The biomass of barley was 449 kg/l0a at heading stage (HS) and increased to 421 kg/10a at 10 days after heading stage (DAH), 473 kg/10a at 20 DAH. C/N ratio of BGM was the lowest 26.3 at HS. The N contents of BGM was in the range of 0.9~1.5%, the highest at HS and gradually decreased, and the output of N were 4.3-6.3 kg/10a. The total amount of nitrogen, phosphorous and potassium of BGM showed the highest level at 10 DAH. Culm length of rice was relatively longer as the BGM application time was delayed. The application of BGM into soil increased plant height of rice by 7.2~7.7 em as compared to the plants treated with commercial fertilizer at recommended rate. but panicle length of rice showed a similar tendency in both the soil-applied of BGM and commercial fertilizer. N contents of unhulled rice was the highest at HS of BGM and followed by 10 DAH of BGM and 20 DAH of BGM. This trend could also be seen in rice straw. The yield of rice in the soil-applied of BGM was 10~15% lower than in the soil-applied of commercial fertilizer. Based on this study, application of BGM made it possible to save 30~50% of application amount of nitrogen fertilizer for following crops.