• Journal of Ocean Engineering and Technology
• /
• v.32 no.5
• /
• pp.380-385
• /
• 2018

With the tightening of environmental regulations (i.e., IMO Tier III), natural gas (NG) has been spotlighted as an eco-friendly fuel with few air pollutants other than nitrogen oxides (NOx) and sulfur oxides (SOx). For reasons of economic efficiency, it is mainly stored and transported in a liquid state at $-163^{\circ}C$, which is a cryogenic temperature, using a liquefied gas storage tank. Accordingly, it is necessary to reduce the boil-off gas (BOG) occurrence due to the heat flow according to the temperature difference between the inside and outside of the storage tank. Therefore, in this study, a BOG measurement test on an independent-type storage tank made up of SUS304L was carried out. The test results showed the tendency for BOG occurrence according to the temperature under different filling ratios.

• Journal of Welding and Joining
• /
• v.27 no.6
• /
• pp.74-79
• /
• 2009

Titanium and titanium alloy can be reproduced immediately even if oxide films($TiO_2$) break apart in sea water. Therefore, since titanium demonstrates large specific strength and outstanding resistance to stress corrosion cracking, crevice corrosion, pitting and microbiologically influenced corrosion in sea water environment, it has been widely applied to heat exchanger for ships. In particular, with excellent elongation, pure titanium may be deemed as optimal material for production of heat exchanger plate which is used with wrinkles formed for efficient heat exchange. Conventional plate type heat exchanger prevented leakage of liquid through insertion of gasket between plates and mechanical tightening by bolts and nuts, but in high temperature and high pressure environment, gasket deterioration and leakage occur, so heat exchanger for LPG re-liquefaction device etc do not use gasket but weld heat exchanger plate for use. On the other hand, since welded plate cannot be separated, it is important to obtain high quality reliable welds. In addition, for better workability and production performance, lasers that can obtain weldment with large aspect ratio and demonstrate fast welding speed even in atmospheric condition not in vacuum condition are used in producing products. So far, 1st report and 2nd report compared and analyzed embrittlement degrees by bead colors of weldment through quantitative analysis of oxygen and nitrogen and measurement of hardness as fundamental experiment for the evaluation of titanium laser welding, and evaluated the welding performance and mechanical properties of butt welding. This study welded specimens in various conditions by using laser and GTA welding machine to apply edge welding to heat exchanger, and evaluated the mechanical strength through tensile stress test. As a result of tensile test, laser weldment demonstrated tensile strength 4 times higher than GTA welds, and porosity could be controlled by increasing and decreasing slope of laser power at overlap area.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.6
• /
• pp.531-542
• /
• 2022

As buildings become taller, the strength of structural materials must increase and the amount of rebar reinforcement also increases while the application of an appropriate rebar splice method in the construction process become one of the essential factors. In this research, the current status of quality check for rebar coupler is identified by an expert questionnaire and an appropriate quality check method is proposed through a quality test on specimens similar to actual on-site construction. In the test results, it was revealed that, among the quality check methods for rebar coupler joints, the coupler tightening method and face to face degree of between upper and lower rebar did not affect the strength the specimen. Therefore, it is considered to be an appropriate way to check the coupler quality check to check whether the threads are completely assembled during on-site construction through manufacture the number of threads of rebar and coupler with a margin beyond the calculated thread number.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.29-37
• /
• 2016

This paper proposes a shape optimization of the metal boss for a composite motor case using finite element analysis. For the structural safety and the weight reduction of the composite motor case, under the internal pressure, the fiber stress in the dome area and the tightening bolt stress are constrained and the boss weight is set to objective function, respectively. The response surface models are constructed for the performance characteristics by using response surface method. The significance of the design variables about the performance characteristics is evaluated through the ANOVA(analysis of variance) and the goodness of fit test for the constructed model is performed through the regression analysis. The SQP(sequential quadratic programming) algorithm is used for the optimization and the proposed method is verified by performing structural analysis for the optimum shape.

• Journal of the Korean Institute of Gas
• /
• v.25 no.5
• /
• pp.19-29
• /
• 2021

Due to the climate changing, the world's countries are tightening regulations on CO2 and air pollutants emission to solve them. In addition, eco friendly vehicles is increasing to replace automobiles in internal combustion engine. Recently, the government is supporting the expansion of hydrogen refueling infrastructure and localization of core equipment in refueling facilities according to the hydrogen economy road map. In this study, design of the Excess flow limiting device in FCEV cylinder valve using by finite element analysis and performed performance tests on prototype. Major test results as hydrostatic strength, continued operation, operation, pressure impulse, leakage showed that the excess flow limiting device meets the performance requirements according to ISO 12619-2 and ISO 12619-11.

• Journal of The Korean Society of Integrative Medicine
• /
• v.8 no.4
• /
• pp.117-123
• /
• 2020

Purpose : VDT (visual display terminal syndrome) can affect individuals who monitor or who work or play using video screens, including those of smartphones. In general, headache symptoms from overuse of these screens can appear due to eye fatigue, muscle pain in the joints of wrists or fingers, and muscle pain in the neck or shoulders. Many studies in the literature have supported standards that seek to prevent these symptoms. The incidence of musculoskeletal diseases caused by the use of smartphones is expected to increase rapidly, particularly among children and young adults, and these diseases are expected to develop into a societal problem. Therefore, in this study we investigate whether tension headaches that develop from smartphone usage can affect forward neck posture, neck pain, and quality of life. Methods : A total of 93 students from University participated in this study. We divided participants into two groups, those with tension headaches (n = 25) and those without (n = 68) and took forward neck measurements. Headaches were classified according to criteria from the International Headache Society and involved bilateral headache position, quality of pressing or tightening pain, mild or moderate pain intensity, and none due to daily physical activity. We surveyed participants using the smartphone addiction diagnosis questionnaire, the Neck Disability Index (NDI), the Headache Impact Test (HIT-6), and the Quality of Life Questionnaire. Results : Although we found no significant differences in tension headaches due to smartphone addiction diagnosis (p = 0.25), SF-36 life quality assessment (p = 0.06), and cranio-vertebral angle (p = 0.07), we found significant differences from the HIT-6 and the NDI (p <.05). Conclusion : Tension headaches are not correlated with smartphone addiction, quality of life, and forward neck angle but do have a correlation with the degree of cervical dysfunction and the effects of the headaches.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.1
• /
• pp.87-93
• /
• 2014

A tightened coupler with two way-threading is suggested to overcome the previous one-way threaded coupler. The experiment and a mock-up test were conducted to analyze the constructability of the suggested coupler. The aim of the mock-up test was to assemble the suggested coupler in horizontal rebar of mat footing and vertical rebar of semi-fabricated column bars. The method using the suggested coupler in semi-fabricated column bars is developed by analyzing the problem of fabricated column bars using the one-way threaded coupler. The result of the mock-up test showed that the time required to assemble the suggested coupler in the horizontal bars is shorter than it is for the one-way threaded coupler. In addition, the method using the suggested coupler in semi-fabricated column bars has advantages such as lower working loads, supporting safe work and strongly tightening the rebar. From these results, it is revealed that the suggested coupler is adequate to use in rebar work in terms of cost, quality and time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.32-38
• /
• 2020

Cargo train braking uses the pressure changes in the air braking pipe to operate the braking tightening and releasing service repeatedly. Air-braking release failure means partial braking caused by a failure of the variable load valve after the driver handling the brake release. This phenomenon causes wheel flaws while driving a wagon, resulting in wheel breakage or train derailment. This study developed the air-braking release failure proof valve considering the technical requirements of the railway operation corporations. In addition, a durability test of the valve was carried out using a braking performance simulator, and its operating performance was evaluated from the pneumatic history under cyclic braking conditions. The warranty life of this valve was assessed by performing 160,000 cycles of testing of 12 prototypes in accordance with the zero-failure test method, considering the number of braking cycles while driving the wagon. During the durability test, the pneumatic input time, output time, and release velocity were almost constant. The warranty life of this valve was 59,860 times the 95% confidence level, which means that it can be operated without trouble for four years when the valve is installed in the bogie of the wagon.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.33 no.2
• /
• pp.114-118
• /
• 2017

Purpose: The aim of this study was to investigate the effects of a titanium component for the zirconia abutment in the internal connection implant system on screw loosening under thermocycling conditions. Materials and Methods: Internal connection titanium abutments and external connection zirconia abutments with titanium sockets were connected respectively to screw-shaped internal connection type titanium implants with 30 Ncm tightening. These implant-screw-abutment assemblies were divided into two groups of five specimens each; titanium abutments as control and zirconia abutments with titanium sockets as experimental group. The specimens were subjected to 2,000 thermocycles in water baths at $5^{\circ}C$ and $55^{\circ}C$, with 60 seconds of immersion at each temperature. The removal torque values (RTVs) of the abutment screws of the specimen were measured before and after thermocycling. RTVs pre- and post-thermocycling were investigated in statistics. Results: There was not screw loosening identified by tactile and visual inspection in any of the specimens during or after thermocycling. The mean RTV difference for the control group and the experimental group were $-1.34{\pm}2.53Ncm$ and $-1.26{\pm}2.06Ncm$, respectively. Statistical analysis using an independent t-test revealed that no significant differences were found in the mean RTV difference of the groups (P > 0.05). Conclusion: Within the limitations of this in vitro study, the titanium socket for the zirconia abutment did not show a significant effect on screw loosening under thermal stress compared to the titanium abutment in the internal connection implant.

• The Journal of Internal Korean Medicine
• /
• v.41 no.5
• /
• pp.705-716
• /
• 2020

Objective: Tension Type Headache is the most common primary headache, and the prevalence is highest among people in their thirties. The 2009 domestic headache epidemiological survey indicated a prevalence rate of 30.8% per year. The patients often complain of feeling "as if they are tightening their head or wearing a band." No other symptoms, such as nausea and vomiting, accompany the headache, and the physical and neurological findings are normal. Korean medicine treatment of tension type headache is mainly with acupuncture, not herbal medicine. In the present study, a patient with tension type headache was admitted to the Korean medicine hospital for treatment. We report on the patient's progress and the effects of the herbal treatment. Methods: The patient was treated with Gaegyeolseogyeong-tang, acupuncture, herbal acupuncture therapy, and physical therapy. We used the Korean Headache Impact Test-6 and Numeric Rating Scale to assess changes in tension type headache symptoms. Results: The patient was diagnosed with Qi-stagnation syndrome (氣滯證) and Ganyangsanghang-headache (肝陽上亢頭痛). The patient was hospitalized for 42 days and showed recovery from the tension type headache without any adverse events. Conclusion: Patients with tension type headache could be treated with Korean medicine.