• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.426-429
• /
• 2001

The BaTiO$_3$+xNb$_2$O$_{5}$[x=6,8 , 10wt%] ceramics were prepared by conventional mixed oxide method. The structural properties of the BaTiO$_3$+xNb$_2$O$_{5}$ ceramics with the sintering temperature and addition of Nb$_2$O$_{5}$ were investigated by XRD and SEM. Increasing the sintering temperature, the 2$\theta$ value of BT (110) peak was shifted to the lower degree and intensity of the BN (310) peak was increased. Increasing the addition of Nb$_2$O$_{5}$, the intensity of BN (100) Peak was decreased and BN (310), (110) peaks were increased. The grain size of the BaTiO$_3$+Nb$_2$O$_{5}$ ceramics sintered at 135$0^{\circ}C$ were almost uniform. In the BaTiO$_3$+Nb$_2$O$_{5}$ ceramics sintered at 135$0^{\circ}C$, the dielectric constant and dielectric loss were 5424, 0.02 respectively.espectively.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.1
• /
• pp.43-48
• /
• 2006

The oxidation behavior and Biocompatibility of pure Ti and Ti-8Ta-3Nb alloy were studied in dry air atmosphere. The specimens showed that Ti-8Ta-3Nb alloy had higher oxidation resistance than pure Ti at $650^{\circ}C$. Cytotoxicity test also revealed that moderate oxidation treatment lower cell toxicity and Ti-8Ta-3Nb alloy showed better results compared with pure Ti. The weight gains during the oxidation increase rapidly at temperature above $600^{\circ}C$.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.44 no.8
• /
• pp.1068-1074
• /
• 1995

Effect of (Zn$_{1}$3/Nb$_{2}$3/) $O_{2}$ addition on the phase changes and microwave dielectric properties of BaTi $O_{3}$-3Ti $O_{2}$ ceramics were investigated. Addition of (Zn$_{1}$3/Nb$_{2}$3/) $O_{2}$ to BaTi $O_{3}$-3Ti $O_{2}$ resulted in the formation of Ba $Ti_{4}$$O_{9}$, $Ba_{2}$ $Ti_{9}$ $O_{20}$, Ba(Zn$_{1}$3/Nb$_{2}$3/) $O_{3}$, and Ti $O_{2}$ phases. Ba $Ti_{4}$$O_{9}$ phase was gradually transformed to $Ba_{2}$ $Ti_{9}$ $O_{20}$. This was identified by XRD and microstructure. As the Ba $Ti_{4}$$O_{9}$ phase transformed to $Ba_{2}$ $Ti_{9}$ $O_{20}$ phase, the dielectric constant increased to 37.5. Q*f$_{o}$ value was 40000 at x=0.04, and the temperature coefficient of resonant frequency was +10ppm/.deg. C.C.. C.C.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.127-130
• /
• 2001

The $BaTiO_3+xNb_2O_5$(x=6, 8, 10wt%) ceramics were prepared by conventional mixed oxide method. The structural properties of the $BaTiO_3+Nb_2O_5$ ceramics with the sintering temperature and addition of $Nb_2O_5$ were investigated by XRD and SEM. Increasing the sintering temperature, the $2{\theta}$ value of BT(110) peak was shifted to the lower degree and intensity of the $Ba_6Ti_2Nb_8O_{30}$ (133) peak was increased. Increasing the addition of $Nb_2O_5$, the intensity of $BaTiNb_4O_{13}$ (201) peak was decreased and $Ba_6Ti_2Nb_8O_{30}$ (133) peak was increased. The grain size of the $BaTiO_3+Nb_2O_5$ ceramics sintered at $1500^{\circ}C$ were almost uniform.

• Journal of Korea Foundry Society
• /
• v.22 no.3
• /
• pp.114-120
• /
• 2002

A new titanium based alloy, Ti-10Ta-10Nb, has designed to examine the improved mechanical properties and biocompatibility. A specimen of titanium alloy was melted in a consumable vacuum arc furnace and homogenized at $1050^{\circ}C$ for 24 h. The effect of hot rolling on microstructure was estimated after rolling at $400^{\circ}C$ and $800^{\circ}C$ respectively. Surface of melted alloy by consumable vacuum arc melting was consisted of rough surface and it was changed to sound surface by coating of $ZrO_2$ slurry on copper mold surface. The hardness of Ti-10Ta-10Nb alloy increased with the amount of${\alpha}+{\beta}$ phase. Ti-10Ta-10Nb alloy showed $Widmanst{\"{a}}ten$ structure by hot rolling at $800^{\circ}C$ and in the rolling ${\beta}-region$ was negligible effects on microstructure refining.

• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.1025-1031
• /
• 1999

Alloys of TiAl with six different compositions. i. e., Ti-(42, 44)Al-2Nb-4V. Ti-(42, 44)Al-4Nb-2V and Ti -(42, 44)Al-4Nb-2Cr, were manufactured by arc-melting. and their oxidation behavior was studied. Both isothermal and cyclic oxidation tests were performed at 700, 800 and $900^{\circ}C$ in air for 50hr. The oxidation resistance increased in the order of Ti-(42, 44)Al-2Nb-4V, Ti-(42, 44)Al-4Nb-ZV and Ti-(42, 44)Al-4Nb-2Cr. It was found that V was a deleterious element, while Cr was a beneficial element in terms of oxidation resistance. During oxidation, a simultaneous interdiffusion was observed. All the constituent elements in the base alloys diffused outward. whereas oxygen from the atmosphere diffused inward, to form triple oxide layers composed of an outermost $\textrm{TiO}_2$ layer. upper ($\textrm{TiO}_2+\textrm{Al}_2\textrm{O}_3$) mixed layer, and lower $\textrm{TiO}_2$-rich layer.

• Journal of the Korean Ceramic Society
• /
• v.33 no.11
• /
• pp.1267-1275
• /
• 1996

Green sheet was prepared by tape casting in the composition of (1-x)Pb(Mg1/3Nb2/3)O3-PbTiO3 system using Pb(Mg1/3Nb2/3)O3 and PbTiO3 synthesized with PbO, Nb2O5 MgO and TiO2 The densest green sheet was obtained in the weight ratio 70:30 of powder to binder. Green sheet wasmultilayered in metal mould and formed into lamination at 7$0^{\circ}C$, 300kg/cm2 The lamination was sintered at 110$0^{\circ}C$ 2hr, Dielectric constant and Curie temperature of disc type sintered body was highered with increasing the amount of PbTiO3 and was in the range of 19000-21000, -7~45$^{\circ}C$ respectively. Green and sintered relative density of lamination was 61% and 95% respectively.

• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.798-807
• /
• 1994

The increase in the resistance of $BaTio_{3}$ with addition of Ca is attributed to the formation ofthe acceptor impurity by $CaCa^{2+}$" which substitutes Ti4+. However, some authors suggested that $Ca^{2+}$ can not substitute $Ti^{4+}$ because of its larger ionic radius. In this work, the existence of acceptor by Ca hasbeen studied through the high temperature equilibrium electrical conductivity of $BaTiO_{3}$ codoped with Caand Nb, where Ba/(Ti+Ca+Nb) was kept equal to unity. It was measured at $1000^{\circ}C$, and the oxygenpartial pressure was controlled between $10^{-15}$ ~ 1 atm. Changing the amount of added Ca and Nbresulted in the compensation effect between donor and acceptor, i.e., Nb was compensated by the acceptor.And through the defect chemical interpretation of the measured data, it was concluded that Ti canbe substitued with Ca. The existence of such acceptor was reaffirmated by ICTS(Isotherma1 CapacitanceTransient Spectroscopy) measurements.oscopy) measurements.

• Journal of the Korean Ceramic Society
• /
• v.36 no.12
• /
• pp.1335-1341
• /
• 1999

The electrical conductivity ($\sigma$) of TiO2 doped with 0.05-4.0mol% Nb2O5 was measured in the oxygen partial pressure range of 10-17 to 100 atm and temperature range of 1100 to 130$0^{\circ}C$ to investigate the electrical properties and defect types. The oxygen partial pressure dependence of the electrical conductivity (log$\sigma$/logPo2) above 110$0^{\circ}C$ was divided into the four regions. From these experimental results the following defect regions were proposed ; 1) Magneli phase(extended defect) 2) reduced rutile region where intrinsic defect predominates 3) nearly stoichiometric region which is independent on the oxygen partical pressure and 4) overstoichiometric region which is not observed in pure TiO2 The electrical conductivity of Nb-doped TiO2 depended on the doping content the oxygen partial pressure and the measuring tem-perature.

• Corrosion Science and Technology
• /
• v.8 no.4
• /
• pp.143-147
• /
• 2009

In biomedical implants and dental fields, titanium has been widely utilized for excellent corrosion resistance and biocompatibility. However, Ti and its alloys are nonbioactive after being implanted in bone. In this study, for the purpose of improvement in biocompatibility the anodic $TiO_2$ layer on Ti-xNb alloys were fabricated by electrochemical method in phosphate solution, and the effect of Nb content on the pore size, the morphology and crystallinity of Ti oxide layer formed by the anodic oxidation method was investigated. The Ti containing Nb up to 3 wt%, 20 wt% and 40 wt% were melted by using a vacuum furnace. The sample were cut, polished, and homogenized for 24 hr at $1050^{\circ}C$ for surface roughness test and anodizing. Titanium anodic layer was formed on the specimen surface in an electrolytic solution of 1 M phosphoric acid at constant current densities ($30mA/cm^2$) by anodizing method. Microstructural morphology, crystallinity, composition, and surface roughness of oxide layer were observed by FE-SEM, XRD, EDS, and roughness tester, respectively. The structure of alloy was changed from $\alpha$-phase to $\beta$-phase with increase of Nb content. From XRD results, the structure of $TiO_2$ formed on the Ti-xNb surface was anatase, and no peaks of $Nb_2O_5$ or other Nb oxide were detected suggesting that Nb atoms are dispersed in $TiO_2$-based solid solution. Surface roughness test and SEM results, pore size formed on surface and surface roughness decreased as Nb content increased. From the line analysis results, intensity of Ti peak was high in the center of pore, whereas, intensity of O peak was high in the outside of pore center.